| Age | Commit message (Collapse) | Author |
|---|
|
- Fix BBL may be corrupted problem.
- Support U-Boot run in S-mode.
|
|
video, bmp and cls command updates
|
|
ax25-ae350 use CONFIG_OF_BOARD via a2 and CONFIG_SYS_SDRAM_BASE
to boot from ram which allow the board to override the fdt
address originally.
But after this patch
riscv: save hart ID and device tree passed by prior boot stage
It provide prior_stage_fdt_address which offer a temporary
memory address to keep the dtb address passing from loader(gdb)
to u-boot with a1.
So passing via a2 and CONFIG_SYS_SDRAM_BASE is redundant and
can be removed. And it also somehow may corrupted BBL if it
was be arranged in CONFIG_SYS_SDRAM_BASE.
In board_fdt_blob_setup()
When boting from ram:
prior_stage_fdt_address will be use to reserved dtb temporarily.
When booting from ROM:
dtb will be pre-burned in CONFIG_SYS_FDT_BASE, if it is flash base.
Or CONFIG_SYS_FDT_BASE maybe a memory map space (NOT RAM or ROM)
which is provided by HW.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
|
|
This patch adds S-mode defconfigs for QEMU virt machine so
that we can run u-boot in S-mode on QEMU using M-mode runtime
firmware (BBL or equivalent).
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
When u-boot runs in S-mode, the M-mode runtime firmware
(BBL or equivalent) uses memory range in 0x80000000 to
0x80200000. Due to this, we cannot use 0x80000000 as
SYS_TEXT_BASE when running in S-mode. Instead for S-mode,
we use 0x80200000 as SYS_TEXT_BASE.
Even Linux RISC-V kernel ignores/reserves memory range
0x80000000 to 0x80200000 because it runs in S-mode.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
This patch adds kconfig option RISCV_SMODE to run U-Boot in
S-mode. When this opition is enabled we use s<xyz> CSRs instead
of m<xyz> CSRs.
It is important to note that there is no equivalent S-mode CSR
for misa and mhartid CSRs so we expect M-mode runtime firmware
(BBL or equivalent) to emulate misa and mhartid CSR read.
In-future, we will have more patches to avoid accessing misa and
mhartid CSRs from S-mode.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
- DT sync with Linux 4.19 and minor fixes.
|
|
Drop BMP_ALIGN_CENTER define in lcd.c and video_bmp.c as it is
already defined by splash.h. Include splash.h in bmp code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Allow to display BMP at the middle of the screen.
'm' means "middle" as it is done for the splashscreen variable:
splashpos=m,m
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add common clear screen command for configurations
CONFIG_DM_VIDEO, CONFIG_LCD and CONFIG_CFB_CONSOLE.
Remove the existing cls command implementation from
lcd.c code and activate the command for all boards
enabling CONFIG_LCD for compatibility reasons.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Patrick.Delaunay <patrick.delaunay@free.fr>
|
|
Bundle DTBs for R8A7795, R8A7796 ULCB variants into single U-Boot
build and let U-Boot choose between them based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Bundle DTBs for R8A7795, R8A7796, R8A77965 Salvator-X variants
into the single U-Boot build and let U-Boot choose between them
based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Drop unused MSTP macros from Gen3 boards. These are no longer needed
as the boards are using clock framework to manipulate clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Set environment variable 'platform' containing the CPU type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Enable extended MMC commands and GPT partition table support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
Synchronize DTs with mainline Linux 4.19.6 ,
commit 96db90800c06d3fe3fa08eb6222fe201286bb778
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The i2c6 node is missing in mainline Linux thus far, pull it
into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The SCIF2 node is not in Linux 4.17 DTs on E3, pull it into U-Boot
specific DT extras until it hits mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The SDHI nodes are not in Linux 4.17 DTs in E3, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The SDHI nodes are missing features supported in upstream U-Boot,
like mode support properties. Pull the extras into U-Boot specific
DT until it hits mainline Linux, to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The CPLD node is missing in Linux 4.17 DTs on H3/M3W ULCB, pull the
node into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The AVB node is not complete in Linux 4.17 DTs on V3M Eagle, pull the
AVB node extras into U-Boot specific DT until they hit mainline Linux,
to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The SDHI nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The USB nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
The RPC DT bindings are still work in progress. Extract the RPC DT node
from the DT to allow easier update and so it can be replaced once the DT
bindings are stable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
Add label to the /soc node, so it can be referenced from the U-Boot DTs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
|
|
Convert all Renesas R-Car boards to bootm_size of 256 MiB and drop both
fdt_high and initrd_high. This change implies that the FDT and initrd
will always be copied into the first 256 MiB of RAM instead of being
used in place, which can cause various kinds of inobvious problems.
The simpler problems include FDT or initrd being overwritten or being
used from unaligned addresses, especially on ARM64. The overhead of
copying the FDT to aligned location is negligible and these problems
go away, so the benefit is significant.
Regarding alignment problems with fitImage. The alignment of DT properties
is always 32 bits, which implies that the alignment of the "data" property
in fitImage is also 32 bits. The /incbin/ syntax plays no role here. The
kernel expects all elements, including DT and initrd, to be aligned to
64 bits on ARM64, thus using them in place may not be possible. Using the
bootm_size assures correct alignment, again with negligible overhead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
According to SD Specifications Part 1 Physical Layer Simplified Specification
Version 6.00 August 29, 2018, section 4.3.10 (Switch Function Command) and
section 5.6 (SCR register), SD cards version 1.00 and 1.01 do not support the
SD CMD 6.
Currently, U-Boot will issue CMD 6 unconditionally in sd_set_card_speed()
while configuring the bus for selected frequency. This will make SD cards
version 1.00 and 1.01 time out and thus fail detection altogether.
Fix this by not sending CMD 6 on such cards. Tested on Matsushita Electric
Industrial Co., Ltd. Japan RP-SD008B / Victor 8MB SD card, CU-SD008, which
is correctly detected with this patch as:
Device: sd@ee160000
Manufacturer ID: 1
OEM: 5041
Name: S008B
Bus Speed: 25000000
Mode : SD Legacy
Rd Block Len: 512
SD version 1.0
High Capacity: No
Capacity: 6.5 MiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Update email address
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
|
|
This reverts commit 6f57c34473d37b8da5e6a3764d0d377d748aeef1 since it
does not seem to work at least on rk3399.
The Rockchip Technical Reference Manual (TRM) for the rk3399 says the baud
rate prescaler register is readable only when USR[0] is zero. Since this
bit is defined as "reserved" in the socfpga cylcone5 TRM, let's rather
drop this than making the ns16550 debug uart more platform specific.
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com
|
|
The biggest part of migration to using CONFIG_BLK is that we need to
have the various subsystems migrated first, so reword the plan here to
reference the new deadlines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As the core of the subsystem has been converted along with some of the
drivers, formalize a deadline for migration.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Soeren Moch <smoch@web.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As much of the USB system has been migrated to DM now, formalize a
deadline for migration.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Given that at this point the MMC subsystem itself has been migrated
along with a number of subsystem drivers, formalize a deadline for
migration.
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Xilinx changes for v2019.01
microblaze:
- Use default functions for memory decoding
- Showing model from DT
zynq:
- Fix spi flash DTs
- Fix zynq_help_text with CONFIG_SYS_LONGHELP
- Tune cse/mini configurations
- Enabling cse/mini testing with current targets
zynqmp:
- Enable gzip SPL support
- Fix chip detection logic
- Tune mini configurations
- DT fixes(spi-flash, models, clocks, etc)
- Add support for OF_SEPARATE configurations
- Enabling mini testing with current targets
- Add mini mtest configuration
- Some minor config setting
nand:
- arasan: Add subpage configuration
net:
- gem: Add 64bit DMA support
|
|
Patch queue for rpi - 2018-12-03
A few Raspberry Pi specific changes this time:
- Allow 2nd MMC device
- Support RPi 3 Model A+
- Allow UUID to find filesystem
|
|
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
|
|
- MMC fixes for R-Car Gen3
|
|
- Baltos platform updates
- rtc m41t62 converted to DM.
- PowerPC MPC8xx DM conversion
- Verified boot updates
|
|
Add Raspberry Pi 3 Model A+ to list of models, the revision code is 0xE
according to the list on raspberrypi.org.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Replace various third party lists of Raspberry Pi revision codes in a
comment with the list on raspberrypi.org.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
At present line_length is always calculated in video_post_probe(). But
some hardware may use a different line length, e.g. with a 1366-wide
display.
Allow the driver to set this value if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
CC common/board_r.o
common/board_r.c:747:2: error: ‘initr_spi’ undeclared here (not in a function)
initr_spi,
^
make[1]: *** [common/board_r.o] Error 1
Fixes: ebe76a2df9f6 ("dm: Remove spi_init() from board_r.c when using driver model")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
