summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-06-06net: dwc_eth_qos: add Ethernet stm32mp1 supportChristophe Roullier
Synopsys GMAC 4.20 is used. And Phy mode for eval and disco is RMII with PHY Realtek RTL8211 (RGMII) We also support some other PHY config on stm32mp157c PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz and 50Mhz), No 125Mhz from PHY config Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-06-06board: stm32mp1: Add board_interface_eth_initChristophe Roullier
Called to configure Ethernet PHY interface selection and configure clock selection in RCC Ethernet clock tree. Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
2019-06-06stm32mp1: clk: use the correct identifier for ethckPatrick Delaunay
ETHCK_K is the identifier the kernel clock for ETH in kernel binding, selected by ETHKSELR / gated by ETHCKEN = BIT(7). U-Boot driver need to use the same identifier, so change ETHCK to ETHCK_K. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
2019-06-06configs: stm32mp15: Enable SPI relative flagsPatrice Chotard
Enable STM32_SPI, SPI, DM_SPI and CMD_SPI flags. This enables the SPI support for STM32MP15. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06spi: stm32: Add Serial Peripheral Interface driver for STM32MPPatrice Chotard
Add SPI driver support for STM32MP SoCs family. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06clk: stm32mp1: Add SPI1 clock entryPatrice Chotard
Add missing SPI1 clock needed by SPI1 instance. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06board: stm32mp1: Update power supply check via USB TYPE-CPatrice Chotard
Add 2 new checks: - detect when USB TYPE-C cable is not plugged correctly. In this case, GND and VBUS pins are connected but not CC1 and CC2 pins. - detect is an USB Type-C charger supplies more than 3 Amps which is not compliant with the USB Type-C specification In these 2 situations, stop the boot process and let red led blinks forever. V cc1 | V cc2 | power supply | red led | console message range (Volts) |range (Volts)| (Amps) | blinks | --------------|-------------|--------------|---------|----------------------------------- > 2.15 | < 0.2 | > 3 | for ever| USB TYPE-C charger not compliant with specification [2.15 - 1.23[ | < 0.2 | 3 | NO | NO [1.23 - 0.66[ | < 0.2 | 1.5 | 3 times | WARNING 1.5A power supply detected [0.66 - 0] | < 0.2 | 0.5 | 2 times | WARNING 500mA power supply detected < 0.2 | < 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode > 0.2 | > 0.2 | | for ever| ERROR USB TYPE-C connection in unattached mode Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable WDT flagsPatrice Chotard
This allows to enable WATCHDOG and WDT flags to be able to reset the watchdog and to support watchdog driver model. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06watchdog: stm32mp: Add watchdog driverPatrice Chotard
This patch adds IWDG (Independent WatchDoG) support for STM32MP platform. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Stefan Roese <sr@denx.de>
2019-06-06ARM: dts: stm32mp: Add iwdg2 support for stm32mp157cPatrice Chotard
This patch adds independent watchdog support for stm32mp157c in SPL. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-06-06watchdog: Kconfig: Sort entry alphabeticallyPatrice Chotard
To make adding new entry easier, sort Kconfig entries in alphabetical order. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Stefan Roese <sr@denx.de>
2019-06-06stm32mp1: Update env_get_location for NOR supportPatrice Chotard
Update env_get_location() to be able to save environment into NOR (SPI_FLASH). Series-cc: pde, cke, pch, uboot-stm32 Cover-letter: Add saveenv support for STM32MP1 This series adds saveenv support for STM32MP1 on several boot devices. STM32MP1 is able to boot on eMMC, sdcard and NOR (NAND support is not fully supported). On eMMC and sdcard, environment is saved in EXT4 partition On NOR, environment is saved in a dedicated partition On NAND, environment is saved in a UBI volume. This series: - enables NAND and NOR support on ev1 board - enables ENV_IS_IN_SPI_FLASH, ENV_IS_IN_UBI, ENV_IS_IN_EXT4 flags - fixes get_mtdparts() - allows to override interface, device and partition for ext4 environment - updates rule to set ENV_IS_NOWHERE value - introduce ENV_IS_IN_DEVICE END Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable ENV_IS_SPI_FLASHPatrice Chotard
Add all relative flags needed by ENV_IS_IN_SPI_FLASH Reserved a 256KB partition in NOR to save the U-Boot environment. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable ENV_IS_IN_UBIPatrice Chotard
Add all relative flags needed by ENV_IS_IN_UBI Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06stm32mp1: Increase ENV_SIZEPatrice Chotard
Increase ENV_SIZE from 4 to 8 Ko Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06mtd: Fix get_mtdparts()Patrice Chotard
When ENV_IS_IN_UBI is enable, get_mtdparts is called before relocation. During first get_mtdparts() call, mtdparts is not available in environment, it can be retrieved by calling board_mtdparts_default(), but following env_set() do nothing as we are before relocation. Finally mtdparts is still not available in environment. At second get_mtdparts() call, use_defaults is false, but mtdparts is still not in environment and is NULL. Remove use_defaults bool, only mtdparts criteria is useful. Fixes: commit 5ffcd50612f6 ("mtd: Use default mtdparts/mtids when not defined in the environment") Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06stm32mp1: Add env_get_location()Patrice Chotard
In case of several environment location support, env_get_location is needed to select the correct location depending of the boot device . Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06configs: stm32mp15: Enable ENV_IS_IN_EXT4 and all relative flagsPatrick Delaunay
Enable ENV_IS_IN_EXT4 and all relative flags to be able to load/save environment in EXT4 partition. This will allows to load/save environment on both sdcard and eMMC. As for stm32mp15, bootfs has not the same partition number on sdcard and on eMMC, we use "auto" key which allows to find the first partition in device with bootable flag which is partition 4 on sdcard and partition 2 on eMMC. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06env: enable saveenv command when one CONFIG_ENV_IS_IN is activatedPatrick Delaunay
Introduce ENV_IS_IN_DEVICE to test if one the CONFIG_ENV_IS_IN_ is defined and support the command saveenv even if CONFIG_ENV_IS_NOWHERE is activated Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-06-06env: allow ENV_IS_NOWHERE with other storage targetPatrice Chotard
Allow U-Boot to get default environment for some boot mode (USB for example), and to select storage location when it is booting from flash device; ENVL_NOWHERE is present in env_locations with other one. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-06-06board: stm32mp1: Add env_ext4_get_dev_part() and env_ext4_get_intf()Patrice Chotard
This allows to : - select the current device to save the environment file - select the correct EXT4 boot device instance and partition to save the environment file. For EXT4, device is mmc, device instance is 0 for sdcard or 1 for eMMC. The partition is set to "auto" to select the first partition with bootable flag. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06env: ext4: Allow overriding interface, device and partitionPatrice Chotard
For platform which can boot on different device, this allows to override interface, device and partition from board code. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06stm32mp1: support dynamic MTDPARTSPatrice Chotard
This patch configure the default value for mtdids and mtparts dynamically according the presence of nor and nand in the board device tree Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06stm32mp1: activate NAND and NOR support on EV1Patrick Delaunay
Add the necessary configuration to have NAND and NOR support on ev1 board for BASIC boot (with SPL) or for TRUSTED boot (with TF-A). STM32MP> nand info Device 0: nand0, sector size 256 KiB Page size 4096 b OOB size 224 b Erase size 262144 b subpagesize 4096 b options 0x00184200 bbt options 0x00060000 STM32MP> sf probe SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, total 64 MiB Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-06-06arm: mach-stm32mp: Add newline to the MAC error messageManivannan Sadhasivam
Without newline, the error message appears for non prgrammed OTP boards looks messsy. Hence add it to look more clean. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06board: stm32mp1: Add Avenger96 board supportManivannan Sadhasivam
Add support for Avenger96 board from Arrow Electronics based on STM32MP157 MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards family and has the following features: SoC: STM32MP157AAC PMIC: STPMIC1A RAM: 1024 Mbyte @ 533MHz Storage: eMMC v4.51: 8 Gbyte microSD Socket: UHS-1 v3.01 Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac Bluetooth®v4.2 (BR/EDR/BLE) USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 LED: 4x User LED, 1x WiFi LED, 1x BT LED More information about this board can be found in 96Boards website: https://www.96boards.org/product/avenger96/ Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-06arm: dts: stm32mp157: Add missing pinctrl definitionsManivannan Sadhasivam
Add missing pinctrl definitions for STM32MP157. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-06-05Merge branch '2019-06-05-master-imports'Tom Rini
- More DaVinci fixes - BuR platform fix
2019-06-05cmd/led: check subcommand "list" instead "l"Heiko Schocher
current implementation for checking if "led list" command is called checks only if "l" is passed to the led command. This prevents switching leds with name which starts also with a "l". So check for passing "list". While at it, also fix a typo in led command usage. Signed-off-by: Heiko Schocher <hs@denx.de>
2019-06-05board: am335x/mux: configure the pins for 8-bit data transfer on MMC1Jean-Jacques Hiblot
This is required for proper operation of the 8-bit data transfers. This fixes transient errors seen on BeagleBone Black. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-06-05board/km: update maintainer e-mailHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
2019-06-05arm: davinci: remove leftover assemblyBartosz Golaszewski
There are no more users of lowlevel_init.S. Remove the file. Suggested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-06-05configs/legoev3: define CONFIG_SKIP_LOWLEVEL_INITDavid Lechner
This adds a define for CONFIG_SKIP_LOWLEVEL_INIT in the legoev3 config. On the EV3, U-Boot is loaded into RAM by another bootloader, so we don't need the lowlevel init in U-Boot. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-06-05ARM: da850evm: Fix reading MAC from SPIAdam Ford
The MAC address is located at at the last 64K of SPI Flash, and it's 6 bytes long. This patch corrects both the length and starting byte of the MAC address. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-06-05arm: omap3: Manually initialize GPIO if OF_CONTROL doesn'tAdam Ford
The commong initialization code manually initializes the GPIO even when OF_CONTROL does it, so we can reduce the code size a bit by not doing it manually when we have device tree support. Using the omap3_logic board (dm3730), the sizes shrunk: Before: text data bss dec hex filename 561066 28596 116880 706542 ac7ee u-boot 55245 1605 1888 58738 e572 spl/u-boot-spl After text data bss dec hex filename 560898 28548 116872 706318 ac70e u-boot 55121 1557 1888 58566 e4c6 spl/u-boot-spl Signed-off-by: Adam Ford <aford173@gmail.com>
2019-06-05ARM: DTS: imx6q-logicpd: Resync with Linux 5.1Adam Ford
Resync imx6q-logicpd with Kernel 5.1.5 Signed-off-by: Adam Ford <aford173@gmail.com>
2019-06-05ARM: davinci: Remove ipam390 linker script from KconfigAdam Ford
With ipam390 support removed in we can remove the reference to the linker script since that case will never be true. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-06-05ARM: davinci: SPL: fix BSS initializationSekhar Nori
U-Boot README recommends initializing SDRAM in board_init_f(). DA850 was doing it as part of board_init_r() (through call to spl_board_init() which calls arch_cpu_init() which calls da850_ddr_setup()) This worked fine till commit 15b8c7505819 ("davinci: da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is full") moved BSS to SDRAM. Functions like mmc_initialize() called in board_init_r() assume BSS is available. Since SDRAM was not initialized when arch/arm/lib/crt0.S tried to initialize BSS to 0, BSS is not initialized correctly. Fix this by simply calling arch_cpu_init() from board_init_f(). Also move preloader_console_init() there to help debug issues with board_init_r(). With this spl_board_init() is no longer needed, we remove it. Tested using MMC/SD boot on OMAP-L138 LCDK board. Tested-by: Adam Ford <aford173@gmail.com> #da850evm Signed-off-by: Sekhar Nori <nsekhar@ti.com> Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
2019-06-05ARM: davinci: omal138_lcdk: fix MMC boot breakage due to driver model conversionSekhar Nori
commit 21af33ed0319 ("ARM: davinci: omapl138_lcdk: Enable DM_MMC") wanted to enable DM_MMC only for U-Boot and not for SPL. But CONFIG_DM_MMC is defined for SPL build too. Because of this MMC device was not getting registered for SPL causing MMC/SD boot breakage. Instead use CONFIG_IS_ENABLED(DM_MMC) which will remain false until CONFIG_SPL_DM_MMC is defined. Tested-by: Adam Ford <aford173@gmail.com> #da850evm Signed-off-by: Sekhar Nori <nsekhar@ti.com> Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
2019-06-05board/BuR/common: fix detection for PSC/STM resetcontrollerHannes Schmelzer
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-06-05Merge git://git.denx.de/u-boot-riscvTom Rini
- Support Microchip MPFS Icicle board. - Enable e1000 and nvme support for qemu. - Enable PCI host ECAM generic driver for qemu. - Increase the environment size to 128kB for qemu.
2019-06-05riscv: Add Microchip MPFS Icicle board supportPadmarao Begari
This patch adds Microchip MPFS Icicle board support. For now, NS16550 serial driver is only enabled. The Microchip MPFS Icicle defconfig by default builds U-Boot for M-Mode with SMP support. Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-06-05riscv: qemu: Enable e1000 and nvme supportBin Meng
Since we have added the PCI support to the 'virt' target, enable e1000 and NVME as alternate network and storage devices for these virtio based devices. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-06-05riscv: qemu: Enable PCI host ECAM generic driverBin Meng
QEMU 4.0.0 'virt' target integrates a generic ECAM PCI host. Enable the driver for it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-06-05riscv: increase the environment size for the qemu-riscv platform to 128kBKarsten Merker
The existing default size of 4kB is too small as the default environment has already nearly that size and defining a single additional environment variable can exceed the available space. Signed-off-by: Karsten Merker <merker@debian.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-06-04Merge git://git.denx.de/u-boot-marvellTom Rini
- Enable MMC in SPL to enable DM MMC booting on helios4 (Dennis)
2019-06-04arm: mvebu: helios4: add MMC to SPL DTDennis Gilmore
This allows SPL to load the main U-Boot image from MMC once DM_MMC is enabled. Signed-off-by: Dennis Gilmore <dennis@ausil.us> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-06-02Merge tag 'efi-2019-07-rc4' of git://git.denx.de/u-boot-efiTom Rini
Pull request for UEFI sub-system for v2019.07-rc4 Corrections for boottime services for protocols and for the SetTime() service are provided. Error messages for the 'setenv -e' and 'bootefi bootmgr' commands are added.
2019-06-02Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
- Basic bug fixes and minor features for 2019.07.
2019-06-01efi_selftest: unit test for OpenProtocolInformation()Heinrich Schuchardt
Provide a unit test that checks that the open protocol information is correctly updated when opening and closing protocols. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
generated by cgit (git 2.34.1) at 2025-02-14 05:34:18 +0000