| Age | Commit message (Collapse) | Author |
|---|
|
Every platform has the same stack setup code in assembly as part of
psci_arch_init.
Move this out into a common separate function, psci_stack_setup, for
all platforms. This will allow us to move the remaining parts of
psci_arch_init into C code, or drop it entirely.
Also provide a stub no-op psci_arch_init for platforms that don't need
their own specific setup code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This enables extra USB controllers which enable use of the 3rd USB
port on the new Orange Pi Plus 2E variant.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The Plus variant of the Orange Pi PC has an eMMC, add support for this.
Note we are using the same u-boot defconfig / dts for both the regular
Orange Pi PC as well as the Orange Pi PC Plus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Now that we know that the BROM stores a value indicating the boot-source
at the beginning of SRAM, use that instead of trying to recreate the
BROM's boot probing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
We always define CONFIG_MISC_INIT_R on sunxi and misc_init_r is never
called in the spl, so the linker will optimize it and parse_spl_header(),
of which it is the only caller, away.
On the tests I've done (Orange Pi PC build) the SPL actually becomes
8 bytes smaller with this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Currently we fill ethaddr with a fixed unique address based on the SoCs
serial (from the sid) to make sure that boards which use the integrated
emac / gmac get a fixed mac rather then a random one.
On some boards the wifi does not come with a fixed mac either, so we need
to also set eth1addr.
This commit changes the ethaddr setting code to check for ethernet%d
aliases (as fdt_fixup_ethernet does) and set an ethaddr variable for
all present aliases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).
BIG Thanks to Andre for providing some of the DT code.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
With a recent bunch of SD3.0 cards in our A20-based board we
experienced data transfer rates of about 250 KiB/s instead of 10 MiB/s
with previous cards from the same vendor (both 4 GB/class 10). By
increasing status register polling rate from 1 kHz to 1 MHz we were
able to reach the original transfer rates again. With the old cards
we now even reach about 16 MiB/s.
Signed-off-by: Tobias Doerffel <tobias.doerffel@ed-chemnitz.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The patch converts one of the "reserved" fields in the sunxi SPL
header to a fel_uEnv_length entry. When booting over USB ("FEL
mode"), this enables the sunxi-fel utility to pass the string
length of uEnv.txt compatible data; at the same time requesting
that this data be imported into the U-Boot environment.
If parse_spl_header() in the sunxi board.c encounters a non-zero
value in this header field, it will therefore call himport_r() to
merge the string (lines) passed via FEL into the default settings.
Environment vars can be changed this way even before U-Boot will
attempt to autoboot - specifically, this also allows overriding
"bootcmd".
With fel_script_addr set and a zero fel_uEnv_length, U-Boot is
safe to assume that data in .scr format (a mkimage-type script)
was passed at fel_script_addr, and will handle it using the
existing mechanism ("bootcmd_fel").
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Upon further review this breaks most other platforms as we need to check
what core we're running on before touching it at all.
This reverts commit d73718f3236c520a92efa401084c658e6cc067f3.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
With the change to set up pinctrl after relocation, link fails to boot. Add
a special case in the link code to handle this.
Fixes: d8906c1f (x86: Probe pinctrl driver in cpu_init_r())
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add support for Advantech SOM-DB5800 with the SOM-6867 installed.
This is very similar to conga-qeval20-qa3-e3845 in that there is a
reference carrier board (SOM-DB5800) with a Baytrail based SoM (SOM-6867)
installed.
Currently supported:
- 2x UART (From ITE EC on SOM-6867) routed to COM3/4 connectors on
SOM-DB5800.
- 4x USB 2.0 (EHCI)
- Video
- SATA
- Ethernet
- PCIe
- Realtek ALC892 HD Audio
Pad configuration for HDA_RSTB, HDA_SYNC, HDA_CLK, HDA_SDO
HDA_SDI0 is set in DT to enable HD Audio codec.
Pin defaults for codec pin complexs are not changed.
Not supported:
- Winbond Super I/O (Must be disabled with jumpers on SOM-DB8500)
- USB 3.0 (XHCI)
- TPM
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
If global NVS says internal UART is not enabled, hide it in the ASL
code so that OS won't see it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Now that platform-specific ACPI global NVS is added, pack it into
ACPI table and get its address fixed up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This introduces quark-specific ACPI global NVS structure, defined in
both C header file and ASL file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This introduces baytrail-specific ACPI global NVS structure, defined in
both C header file and ASL file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds support to enable and use the internal BayTrail UART
instead of the one integrated in the Super IO Winbond chip. For this,
a 2nd defconfig file is added.
This is useful for tests done for the congatec SoM used on baseboards
without such a Super IO chip.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
For any FSP-enabled boards that want to enable debug UART support,
setup_internal_uart() will be called, but this API is only available
on BayTrail platform. Change to wrap it with CONFIG_INTERNAL_UART.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There are quite a number of BayTrail boards that uses an external
SuperIO chipset to provide the legacy UART. For such cases, it's
better to have a Kconfig option to enable the internal UART.
So far BayleyBay and MinnowMax boards are using internal UART as
the U-Boot console, enable this on these two boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
For consistency with board_should_run_oprom(), do the same to
should_load_oprom(). Board support codes can provide this one
to override the default weak one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At present should_load_oprom() calls board_should_run_oprom() to
determine whether oprom should be loaded. But sometimes we just
want to load oprom without running. Make them independent.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This option is defined at nowhere. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
The following python error:
Traceback (most recent call last):
File "./tools/patman/patman", line 144, in <module>
series = patchstream.FixPatches(series, args)
File "./tools/patman/patchstream.py", line 477, in FixPatches
commit = series.commits[count]
IndexError: list index out of range
is seen when:
- 'END' is missing in those tags
- those tags are put in the last part in a commit message
- the commit is not the last commit of the series
Add testing logic to see if a new commit starts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
'Series-changes' uses blank line to indicate its end. If that is
missing, series internal state variable 'in_change' may be wrong.
Correct its state.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
If 'END' is missing in a 'Cover-letter' section, and that section
happens to show up at the very end of the commit message, and the
commit is the last commit of the series, patman fails to generate
cover letter for us. Handle this in CloseCommit of patchstream.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
'Cover-letter', 'Series-notes' and 'Commit-notes' tags require an
'END' to be put at the end of its section. If we forget to put an
'END' in those sections, and these sections are followed by another
patman tag, patman generates incorrect patches. This adds codes to
handle such scenario.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Like other patman tags, use a new variable cover_match to indicate
a match for 'Cover-letter'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Some uclass ids are out of order. Per the comments, sort them
in alphabetical order.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The cros-ec keyboard is always a child of the cros-ec node. Rather than
searching the device tree, looking at the children. Remove the compat string
which is now unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The 'COMPAT_' part should appear only once so drop the duplicate part. It is
ignored anyway, but let's keep things consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The list is shrinking and we should avoid adding new things. Instead, a
proper driver should be created with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
A few drivers have moved to driver model, so we can drop these strings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
We have drivers for several more devices now, so drop the strings which are
no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This fixes the following compiler error:
common/fb_mmc.c: In function ‘fb_mmc_erase’:
common/fb_mmc.c:209:17: error: ‘struct blk_desc’ has no member named
‘block_erase’
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Define a platform data structure for the MPC85XX GPIO driver to allow
use of the driver without device tree. Users should define the GPIO
blocks for their platform like this:
struct mpc85xx_gpio_plat gpio_blocks[] = {
{
.addr = 0x130000,
.ngpios = 32,
},
{
.addr = 0x131000,
.ngpios = 32,
},
};
U_BOOT_DEVICES(my_platform_gpios) = {
{ "gpio_mpc85xx", &gpio_blocks[0] },
{ "gpio_mpc85xx", &gpio_blocks[1] },
};
This is intended to build upon the recent submission of the base
MPC85XX driver from Mario Six. We need to use that new driver
without dts support and this patch gives us that flexibility.
This has been tested on a Freescale T2080 CPU, although only the first
GPIO block.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Update the method of accessing the block device so that it works with
CONFIG_BLK enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update the method of accessing the block device so that it works with
CONFIG_BLK enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now that we have fully moved to driver model, drop the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update this board to use driver model for block devices and MMC operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for using driver model for block devices and MMC operations in
this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for using driver model for block devices and MMC operations in
this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move the configuration setting into a separate function which can be used by
the driver-model code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update the sandbox MMC emulation to use driver model for MMC operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These boards should have maintainer entries. Add them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable this option to move rockchip over to use driver model for MMC
operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support to dwmmc for using driver model for MMC operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
