summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-10-08i.MX7ULP: Add CONFIG_MX7ULP to kconfigYe Li
Since many drivers need this CONFIG_MX7ULP to distiguish the settings for i.MX7ULP only. Add this entry to cpu's kconfig. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix PCC register bits mask and offset issueYe Li
The offset for FRAC and the mask for PCD are not correct. If we set FRAC, we can't get the right frequency. Fix them to correct value. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Correct the clock indexBai Ping
On i.MX7ULP, value zero is reserved in SCG1 RCCR register, so the val should be decreased by 1 to get the correct clock source index. Signed-off-by: Bai Ping <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix system reset after a7 rtc alarm expired.Bai Ping
The board will reboot if A7 core enter mem mode by rtc, then M4 core enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode to fix this issue. Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access it. So check the CPU rev and not apply the settings for B0. Signed-off-by: Bai Ping <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb bootPeng Fan
Since the SD3.0 kernel driver needs M4 image support, this causes problem for usb boot booting into kernel. To decouple the relationship, we modify the FDT file in u-boot to disable SD3.0. So the kernel won't depend on M4 image. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: i.MX7ULP: add get_boot_devicePeng Fan
Add get_boot_device for i.MX7ULP Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Fabio Estevam <festevam@gmail.com>
2019-10-08configs: nitrogen6x: Add DM_SPI/DM_SPI_FLASH supportTroy Kisky
Add CONFIG_DM_SPI/CONFIG_DM_SPI_FLASH to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_GPIO supportTroy Kisky
Add CONFIG_DM_GPIO to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This is in preparation for adding CONFIG_DM_SPI. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08nitrogen6x: reserve used gpiosTroy Kisky
This prevents messages like gpio@20a0000: get_value: error: gpio GPIO2_2 not reserved when CONFIG_DM_GPIO is enabled. Also, when CONFIG_DM_GPIO is enabled, checkboard is too early to use gpio_get_value, so read it directly on failure. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08configs: nitrogen6x: Add DM_MMC/DM_USB/AHCI supportTroy Kisky
Add DM_MMC to all defconfigs whose board is nitrogen6x. mx6qsabrelite_defconfig nitrogen6dl2g_defconfig nitrogen6dl_defconfig nitrogen6q2g_defconfig nitrogen6q_defconfig nitrogen6s1g_defconfig This commit is adding multiple configs, but seems to be the minimum change to not lose features and still compile fine. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08nitrogen6x: migrate to using device treeTroy Kisky
Migrate to using device tree required for further driver model integration. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08ARM: imx: Support larger SPL size on IMX6DQRobert Hancock
Previously the SPL size on all iMX6 platforms was restricted to 68KB because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the other iMX6 variants have 256KB of OCRAM. Add an option CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which don't need to support the SL/DL variants. This allows for an SPL size of 196KB, which makes it much easier to use configurations such as SPL with driver model and FDT control. Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
2019-10-08spl: imx: only use HAB if spl fit signature is not enabledRicardo Salveti
There is no need to use HAB for FIT signature validation when SPL_FIT_SIGNATURE is also enabled, as that will be validated via the normal U-Boot signed FIT image flow. This allows having SPL validated by HAB and the payloads to follow being validated with FIT signatures only. Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: apalis_imx6: select MX6Q via KconfigRicardo Salveti
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q variants, which are quite similar and already managed via only one dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in order to automatically enable the HAS_CAAM and MX6_SMP features. Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08apalis_imx6: fix broken fsl_esdhc_imx conversionRicardo Salveti
Commit e37ac717d796 ("Convert to use fsl_esdhc_imx for i.MX platforms") converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for apalis_imx6 wasn't updated accordantly. Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08apalis_imx6: add board_fit_config_name_match to support FIT in SPLRicardo Salveti
Only one dtb is currently supported, so match with imx6-apalis. Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08arm: dts: imx: fsl-imx8qm.dtsi: add gpio aliases to fix gpio commandPeng Fan
The gpio command currently uses equal bank names "GPIO0_" for all existing gpio banks, i. e.: U-Boot# gpio status -a Bank GPIO0_: GPIO0_0: input: 0 [ ] GPIO0_1: input: 0 [ ] ... Bank GPIO0_: GPIO0_0: input: 0 [ ] GPIO0_1: input: 0 [ ] ... So the command is broken, it is not possible to address a desired bank. Add gpio aliases to fix this. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08spl: pass args to board_return_to_bootromPeng Fan
Pass spl_image and bootdev to board_return_bootrom. i.MX8MN needs the args to let ROM to load images Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-10-08serial: Kconfig: make MXC_UART usable for MX7 and IMX8MPeng Fan
i.MX7 and i.MX8M use mxc uart driver, so let's make the SoC could use MXC_UART kconfig. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com>
2019-10-08tools: imx8mimage: fix HDMI/FIT parsingPeng Fan
Add missed break for HDMI entry. And moving FIT parsing earlier, because it does not have parameter, it will not runs into CFG_REG_SIZE. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-10-08pinctrl: imx: use devfdt_get_addr_size_indexPeng Fan
fdtdec_get_addr_size could not parse addr/size correctly is using address-cells 2 and size-cells 2 on an ARM32 SoC. So switch to use devfdt_get_addr_size_index. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6slevk: enable DM_SPI and DM_SPI_FLASHPeng Fan
With DM_SPI and DM_SPI_FLASH enabled, we could get: spi 0 [ ] mxc_spi | | | `-- ecspi@02008000 spi_flash 0 [ ] spi_flash_std | | | `-- m25p80@0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6ul_14x14_evk: convert to DM_VIDEOPeng Fan
To support DM_VIDEO, Add display node for lcdif Drop board iomuxc settings. Enable DM_VIDEO Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08imx: mx6ul_14x14_evk: Fix SPL bootPeng Fan
When booting SPL on the board, met boot failure: " Trying to boot from MMC2 MMC Device 1 not found spl: could not find mmc device 1. error: -19 SPL: failed to boot from all boot devices " Let's register the two mmc controllers in SPL stage to avoid boot failure. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08imx: add i.MX6ULZ boardPeng Fan
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible with i.MX6ULL. so most code of i.MX6ULL can be reused by i.MX6ULZ. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08imx: add i.MX6ULZ cpu typePeng Fan
Add i.MX6ULZ cpu type and helper. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08arm: dts: import dts for i.MX6ULZPeng Fan
Import kernel dts for i.MX6ULZ from commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08arm: dts: sync dts for i.MX6ULLPeng Fan
Sync kernel dts for i.MX6ULL from commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08arm: dts: sync dts for i.MX6ULPeng Fan
Sync kernel dts for i.MX6UL from commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08kconfiglib: Update to the 12.14.0 releaseTom Rini
A large number of changes have happened upstream since our last sync which was to 375506d. The reason to do the upgrade at this point is for improved Python 3 support. As part of this upgrade we need to update moveconfig.py and genboardscfg.py the current API. This is: - Change "kconfiglib.Config" calls to "kconfiglib.Kconfig" - Change get_symbol() calls to syms.get(). - Change get_value() to str_value. Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08genboardscfg.py: Remove "warnings" print sectionTom Rini
We tell kconfiglib to not print any warnings to us so drop this code as it will be unused. Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08genboardscfg.py: Convert to Python 3Tom Rini
Convert this tool to requiring Python 3. The bulk of this is done with the 2to3 tool In addition, we need to use the '//' operator to have our division result return an int rather than a float and ensure that we use UTF-8 when reading/writing files. Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08arm64: versal: remove debug uart for versal virtIbai Erkiaga
Remove the debug uart configuration from versal virtual defconfig. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Introduce virtual defconfigIbai Erkiaga
Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Introduce virtual defconfigIbai Erkiaga
Add virtual defconfig for ZynqMP architecture using of_board dtb. This defconfig should become generic config for all ZynqMP boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: xilinx: Enable generic of_board_dtbIbai Erkiaga
Modify the configuration naming to be generic to xilinx rather than specific to Versal. The offset value is different for Zynq and ZynqMP to avoid overlapping with FSBL. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Move common board dtb searchIbai Erkiaga
Move the exisiting function of getting board dtb from versal to a common Xilinx folder. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Use mailbox driver for PMUFW config loadingMichal Simek
With new mailbox driver PMUFW configuration object can be loaded via the same interface and there is no need to have pmu_ipc.c completely. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2019-10-08firmware: zynqmp: Separate function for sending message via mailboxMichal Simek
U-Boot running in EL3 can't use SMC that's why there is a need to talk to PMUFW directly via mailbox. The same logic is applied to all functions which need to talk to PMUFW that's why move this logic to separate function to avoid code duplication. Also SMC request ID can be composed from PM_SIP_SVC offset that's why ZYNQMP_SIP_SVC_GET_API_VERSION macro can be removed completely. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: probe firmware driverIbai Erkiaga
Probe ZynqMP firmware driver on the board initialization phase and ensure that firmware is in place to continue execution. The probing is done on board_init so it can be used for both SPL and U-Boot proper. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: remove old fw version functionIbai Erkiaga
Removes the old function to get the firmware version. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: use firmware driver to get versionIbai Erkiaga
Use the new function from firmware version to get the firmware version. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08firmware: zynqmp: create firmware headerIbai Erkiaga
New firmware header to place firmware specific macro and function declarations. The patch also moves the macros defining PM operations as well as some helper macros. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08firmware: zynqmp: get fw version with mailbox driverIbai Erkiaga
Implements the function to get PMU Firmware version using the mailbox driver or smc call based on if running SPL or not. Additionally gets version as part of the ZynqMP Firmware driver probing Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Cleanup PM SMC macro compositionMichal Simek
Cleanup PM ID handling by using enum values. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: add firmware and mailbox node to DTIbai Erkiaga
The following patch adds a mailbox node and firmware node to following the mainline DT. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08firmware: zynqmp: Add zynqmp-power supportIbai Erkiaga
zynqmp-power driver for ZynqMP to handle the communication with the PMU firmware. Firmware driver just probes subnodes and power driver handles communication with PMU using the IPI mailbox driver. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08mailbox: zynqmp: ipi mailbox driverIbai Erkiaga
ZynqMP mailbox driver implementing IPI communication with PMU. This would allow U-Boot SPL to communicate with PMUFW to request privileged operations. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08mailbox: allow subnode for mbox regsIbai Erkiaga
The following patch allows the mailbox node in DT to host subnodes with mailbox definitions. If the client phandle to the mailbox is not the mailbox driver node, just checks parents as well. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08mailbox: check ops prior callingIbai Erkiaga
Check if request and free operations are present prior calling to the functions. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2025-01-27 12:02:11 +0000