summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-10-29ext4: Fix printf() format string errorSimon Glass
Fix the following error in the ext4 command: cmd_ext4.c:110:3: error: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'int' [-Werror=format] Signed-off-by: Simon Glass <sjg@chromium.org>
2012-10-29FPGA: Cyclon II: Correctly reset the FPGA before configurationStephan Gatzka
Deassert the CONFIG pin before asserting it again. This assures that the FPGA will be resetted and therefore configuration will be correctly enabled. This is also already done on other FPGA's, e.g. Stratix. Signed-off-by: Stephan Gatzka <stephan.gatzka@hbm.com> Signed-off-by: Stefan Roese <sr@denx.de>
2012-10-29fs: add filesystem switch libary, implement ls and fsload commandsStephen Warren
Implement "ls" and "fsload" commands that act like {fat,ext2}{ls,load}, and transparently handle either file-system. This scheme could easily be extended to other filesystem types; I only didn't do it for zfs because I don't have any filesystems of that type to test with. Replace the implementation of {fat,ext[24]}{ls,load} with this new code too. Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-10-29fs: separate CONFIG_FS_{FAT, EXT4} from CONFIG_CMD_{FAT, EXT*}Stephen Warren
This makes the FAT and ext4 filesystem implementations build if CONFIG_FS_{FAT,EXT4} are defined, rather than basing the build on whether CONFIG_CMD_{FAT,EXT*} are defined. This will allow the filesystems to be built separately from the filesystem-specific commands that use them. This paves the way for the creation of filesystem-generic commands that used the filesystems, without requiring the filesystem- specific commands. Minor documentation changes are made for this change. The new config options are automatically selected by the old config options to retain backwards-compatibility. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2012-10-29fs: delete unused MakefileStephen Warren
fs/Makefile is unused. The top-level Makefile sets LIBS-y += fs/xxx and hence causes make to directly descend two directory levels into each individual filesystem, and it never descends into fs/ itself. So, delete this useless file. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: Simon Glass <sjg@chromium.org>
2012-10-29Merge branch 'master' of git://git.denx.de/u-boot-coldfireTom Rini
2012-10-29ColdFire: Remove save env in NAND support for M54418TWR board.Jason Jin
This patch remove the env saving in NAND as so far the NAND driver is not ported to the M54418TWR platform. Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2012-10-29ColdFire: Update the lds file for M54418TWR board.Jason Jin
The M54418TWR lds file need to update since commit: 8b493a52367623f36e628e4ab2cf8ee082b655e0 common: Discard the __u_boot_cmd section The command declaration now uses the new LG-array method to generate list of commands. Thus the __u_boot_cmd section is now superseded and redundant and therefore can be removed. Also, remove externed symbols associated with this section from include/command.h . Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2012-10-28ESTEEM192E: adjust linker script to grown code sizeWolfgang Denk
Once more, some of the previous changes caused the code to grow, which causes errors like u-boot.lds:74 cannot move location counter backwards (from 40008384 to 40008000) when building with some older tool chains (like ELDK 4.2). Adjust the linker script to make fit again. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Conn Clark <clark@esteem.com>
2012-10-28TQM8xx: adjust linker script to grown code sizeWolfgang Denk
Once more, some of the previous changes caused the code to grow, which causes errors like u-boot.lds:80 cannot move location counter backwards (from 400082a4 to 40008000) when building with some older tool chains (like ELDK 4.2). Adjust the linker script to make fit again. Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-10-28PPC: remove dead boards (AMX860, c2mon, ETX094, IAD210, LANTEC, SCM)Wolfgang Denk
These boards have long reached EOL, and there has been no indication of any active users of such hardware for years. Get rid of the dead weight. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Grandegger <wg@denx.de>
2012-10-26Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2012-10-26ARM: fix u-boot.lds for -ffunction-sections/-fdata-sectionsStephen Warren
When -ffunction-sections or -fdata-section are used, symbols are placed into sections such as .data.eserial1_device and .bss.serial_current. Update the linker script to explicitly include these. Without this change (at least with my gcc-4.5.3 built using crosstool-ng), I see that the sections do end up being included, but __bss_end__ gets set to the same value as __bss_start. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Allen Martin <amartin@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2012-10-26arm: ks8695: use defined constants for UARTYann Vernier
CONFIG_BAUDRATE and KS8695_UART_LINEC_WLEN8 used for UART registers
2012-10-26Origen: Add default clock settings for multimedia IPsAnnamalai Lakshmanan
Added clock settings for MFC, FIMC, FB and G3D. They are clocked to maximum respective frequencies as per datasheet. Signed-off-by: Annamalai Lakshmanan <annamalai.lakshmanan@linaro.org> Signed-off-by: Giridhar Maruthy <giridhar.maruthy@linaro.org> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
2012-10-26arm: arm925t: remove SX1 boardAlbert ARIBAUD
SX1 does not build properly by itself, is not built as part of MAKEALL arm or MAKEALL -a arm, and is only present in Makefile, not boards.cfg. As it also has no entry in MAINTAINERS, it is orphan and non-functional. Remove it. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2012-10-26arm720: Remove CONFIG_ARM7_REVDMarek Vasut
This is a dead code, remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm720: Further clean up the arm720t directoryMarek Vasut
Clean up away old macros and such, so the file doesn't start piling up cruft. Signed-off-by: Marek Vasut <marex@denx.de> clean
2012-10-26stdio: Remove the CLPS7111 serial driverMarek Vasut
This driver is no longer used, remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for NETARMMarek Vasut
This stuff has been rotting in the tree for a while now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for s3c4510Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26arm: Remove support for lpc2292Marek Vasut
This stuff has been rotting in the tree for a year now. Remove it. Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26serial: remove calls to serial_assign()Allen Martin
Remove calls to serial_assign() that are failing now that it returns a proper error code. This calls were not actually doing anything because they passed the name of a stdio_dev when a serial_device name is exptectd. Signed-off-by: Allen Martin <amartin@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com>
2012-10-26Merge remote-tracking branch 'u-boot-atmel/master'Albert ARIBAUD
2012-10-26Merge remote-tracking branch 'u-boot-ti/master'Albert ARIBAUD
2012-10-25FAT: implement fat_set_blk_dev(), convert cmd_fat.cStephen Warren
This makes the FAT filesystem API more consistent with other block-based filesystems. If in the future standard multi-filesystem commands such as "ls" or "load" are implemented, having FAT work the same way as other filesystems will be necessary. Convert cmd_fat.c to the new API, so the code looks more like other files implementing the same commands for other filesystems. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2012-10-25FAT: initialize all fields in cur_part_info, simplify initStephen Warren
cur_part_info.{name,type} are strings. So, we don't need to memset() the entire thing, just put the NULL-termination in the first byte. Add missing initialization of the bootable and uuid fields. None of these fields are actually used by fat.c. However, since it stores the entire disk_partition_t, we should make sure that all fields are valid. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2012-10-25FAT: remove cur_part_nrStephen Warren
A future patch will implement the more standard filesystem API fat_set_blk_dev(). This API has no way to know which partition number the partition represents. Equally, future DM rework will make the concept of partition number harder to pass around. So, simply remove cur_part_nr from fat.c; its only use is in a diagnostic printf, and the context where it's printed should make it obvious which partition is referred to anyway (since the partition ID would come from the user command-line that caused it). Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2012-10-25drivers/serial/serial_ns16550.c: sparse fixesKim Phillips
serial_ns16550.c:222:1: warning: symbol 'eserial1_init' was not declared. Should it be static? serial_ns16550.c:222:1: warning: symbol 'eserial1_setbrg' was not declared. Should it be static? serial_ns16550.c:222:1: warning: symbol 'eserial1_getc' was not declared. Should it be static? serial_ns16550.c:222:1: warning: symbol 'eserial1_tstc' was not declared. Should it be static? serial_ns16550.c:222:1: warning: symbol 'eserial1_putc' was not declared. Should it be static? serial_ns16550.c:222:1: warning: symbol 'eserial1_puts' was not declared. Should it be static? serial_ns16550.c:225:1: warning: symbol 'eserial2_init' was not declared. Should it be static? serial_ns16550.c:225:1: warning: symbol 'eserial2_setbrg' was not declared. Should it be static? serial_ns16550.c:225:1: warning: symbol 'eserial2_getc' was not declared. Should it be static? serial_ns16550.c:225:1: warning: symbol 'eserial2_tstc' was not declared. Should it be static? serial_ns16550.c:225:1: warning: symbol 'eserial2_putc' was not declared. Should it be static? serial_ns16550.c:225:1: warning: symbol 'eserial2_puts' was not declared. Should it be static? serial_ns16550.c:228:1: warning: symbol 'eserial3_init' was not declared. Should it be static? serial_ns16550.c:228:1: warning: symbol 'eserial3_setbrg' was not declared. Should it be static? serial_ns16550.c:228:1: warning: symbol 'eserial3_getc' was not declared. Should it be static? serial_ns16550.c:228:1: warning: symbol 'eserial3_tstc' was not declared. Should it be static? serial_ns16550.c:228:1: warning: symbol 'eserial3_putc' was not declared. Should it be static? serial_ns16550.c:228:1: warning: symbol 'eserial3_puts' was not declared. Should it be static? serial_ns16550.c:231:1: warning: symbol 'eserial4_init' was not declared. Should it be static? serial_ns16550.c:231:1: warning: symbol 'eserial4_setbrg' was not declared. Should it be static? serial_ns16550.c:231:1: warning: symbol 'eserial4_getc' was not declared. Should it be static? serial_ns16550.c:231:1: warning: symbol 'eserial4_tstc' was not declared. Should it be static? serial_ns16550.c:231:1: warning: symbol 'eserial4_putc' was not declared. Should it be static? serial_ns16550.c:231:1: warning: symbol 'eserial4_puts' was not declared. Should it be static? Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-25drivers/i2c/fsl_i2c.c: sparse fixKim Phillips
fsl_i2c.c:217:14: warning: symbol 'get_i2c_clock' was not declared. Should it be static? Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
2012-10-25am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbersPeter Korsgaard
So other parts can be added. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: support board specific ddr settingsPeter Korsgaard
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code, so other boards can use different types/timings. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make apply with rtc32k_enable() in the file] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx: move generic parts of pinmux handling out from board/ti/am335xPeter Korsgaard
So they are available for other boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx/board: use cpu_mmc_init() for default mmc initializationPeter Korsgaard
So platforms can override it with board_mmc_init() if needed. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: move ti i2c baseboard header handling to board/ti/am335x/Peter Korsgaard
The i2c header is specific to ti(-derived) boards, and not generic for all am335x boards. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Make re-apply with rtc32k_enable() applied] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25am33xx/board.c: make wdtimer/uart_base staticPeter Korsgaard
Only used here (and uart_base only for SPL). Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25am33xx: Add SPI SPL as an optionTom Rini
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE define. Finally, enable the options on the am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25omapimage: Add support for byteswapped SPI imagesTom Rini
Add MLO.byteswap as a target to spl/Makefile and un-guard the first MLO rule so we don't have to duplicate it. Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25omap3_spi: introduce CONFIG_OMAP3_SPI_D0_D1_SWAPPEDPeter Korsgaard
D0/D1 Swapped or not is a board property, not anything specific to the am33xx SoC, so add a custom define for it. At the same time correct the bit handling for the swapped mode (DPE0 should be cleared and SI/DPE1 set). Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25OMAP3: add video support to the mcx boardStefano Babic
Add video support to the board with the display focaltech etm070003dh6. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-25VIDEO: add macro to set LCD size for DSS driverStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2012-10-25OMAP3: mcx: updated to new hardware revisionStefano Babic
Some GPIOs differ in the new revision board. Previous revision are considered obsolete and they will not anymore supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-25OMAP3: updated pinmux and environment for new revision of mcx boardStefano Babic
The mcx board was slightly modified and the pinmux must be updated. There is no need to support the old board, that becomes obsolete. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-25OMAP3: mt_ventoux: power on USB at startupStefano Babic
Updated revision of the board uses GPIOs to activate the USB ports. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-25am335x: Enable RTC 32K OSC clockVaibhav Hiremath
In order to support low power state, you must source kernel system timers to persistent clock, available across suspend/resume. In case of AM335x device, the only source we have is, RTC32K, available in wakeup/always-on domain. Having said that, during validation it has been observed that, RTC clock need couple of seconds delay to stabilize the RTC OSC clock; and such a huge delay is not acceptable in kernel especially during early init and also it will impact quick/fast boot use-cases. So, RTC32k OSC enable dependency has been shifted to SPL/first-bootloader. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-10-24ColdFire: Add Freescale MCF54418TWR ColdFire development board supportAlison Wang
Add Freescale MCF54418TWR ColdFire development board support. Signed-off-by: TsiChung Liew <tsicliew@gmail.com> Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Alison Wang <b18965@freescale.com>
2012-10-24ColdFire: Add MCF5441x CPU supportAlison Wang
Add MCF5441x CPU support. The MCF5441x devices are a family of highly-integrated 32-bit microprocessors based on the Version 4m ColdFire microarchitecture, comprising of the V4 integer core, memory management unit(MMU) and enchanced multiply-accumulate unit(EMAC). Signed-off-by: TsiChung Liew <tsicliew@gmail.com> Signed-off-by: Jason Jin <Jason.jin@freescale.com> Signed-off-by: Alison Wang <b18965@freescale.com>
2012-10-24ColdFire: Fix unused variable in cpu_init.cAlison Wang
Fix the following build warnings in cpu_init.c: cpu_init.c: In function 'cpu_init_f': cpu_init.c:47:9: warning: unused variable 'pll' cpu_init.c:46:10: warning: unused variable 'fbcs' cpu_init.c:44:10: warning: unused variable 'scm1' Signed-off-by: Alison Wang <b18965@freescale.com>
2012-10-23km83xx: add kmvect1 boardGerlando Falauto
Add support for the new kmvect1 board powered by the mpc8309 processor. As this board is very similar to the existing suvd3, instead of adding a new config header file, just add a new config option to suvd3.h Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-23km83xx: add common support for km8309 boardsGerlando Falauto
Add support for Keymile boards based on mpc8309 (it would be only kmvect1 for now) Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> [#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully] Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-26 13:05:43 +0000