| Age | Commit message (Collapse) | Author |
|---|
|
disable video, as not really needed longer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add some defines and get rid of USB warning.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
enable CONFIG_DM for the socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add u-boot specific dtsi file for socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add socrates device tree from linux:
commit 71ae5fc87c34 ("Merge tag 'linux-kselftest-5.2-rc1' of
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest")
and added SPDX license identifier.
Did not fix checkpatch warnings:
arch/powerpc/dts/socrates.dts:235: check: Please don't use multiple blank lines
arch/powerpc/dts/socrates.dts:238: error: code indent should use tabs where possible
Also, add me as board maintainer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
suppress warning:
Flash: ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
add DM based PCI Configuration space access support for
MPC85xx PCI Bridge. This driver is based on
arch/powerpc/cpu/mpc85xx/pci.c
In the old driver there is a fix for a hw issue on the
TARGET_MPC8555CDS and TARGET_MPC8541CDS boards. As I
have no such hardware I did not port this part.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
With python3 we're now tripping over a long-standing problem with how we
add to the buildman file with some toolchains. We cannot have multiple
toolchain-alias sections as that leads to a parse error.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Update to latest libfdt and pylibfdt, with added size control
Update binman, dtoc, patman, buildman to Python 3
Update move_config, rkmux, microcode_tool to Python 3
|
|
add phy-reset-gpios to reset phy
Add board_phy_config to configure phy
Enable DM_ETH
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add more clks for fec_mxc according to Linux Kernel 5.4.0-rc1
drivers/net/ethernet/freescale/fec_main.c.
Since i.MX8MQ not support CLK_CCF, so add a check to restrict
the code only effect when CONFIG_IMX8M and CONFIG_CLK_CCF both defined.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Make FEC driver could be used by i.MX8M when CONFIG_FEC_MXC defined
in defconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
Drop assigned clocks for clk node, this will break boot on i.MX8MM EVK
board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add set_parent callback, then assigned-clock-parents in dts could
be work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
Add enet ref/timer/PHY_REF/root clk which are required to make enet
function well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
When CONFIG_$(SPL_)CLK not defined, the clock controller device
not exist, so to avoid boot failure for platform not have
CONFIG_$(SPL_)CLK, add a check.
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Support pinctrl/clk/sdhc, include ddr4 timing data.
Log:
U-Boot SPL 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)
Normal Boot
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
U-Boot 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)
CPU: Freescale i.MX8MNano rev1.0 at 24 MHz
Reset cause: POR
Model: NXP i.MX8MNano DDR4 EVK board
DRAM: 2 GiB
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add dtsi for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add cfg file for i.MX8MN DDR4
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8MM ccf driver support.
Modifed from Linux Kernel 5.3.0-rc1, drop some entries
that not used in U-Boot and adapt to U-Boot CCF style.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Lukasz Majewski <lukma@denx.de>
|
|
some boards use ddr4, not lpddr4, so we need to check ddr4 firmware.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Support i.MX8MN in imx8m pinctrl driver
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The IVT offset is changed on i.MX8MN. Use ROM_VERSION to pass the
v1 or v2 to mkimage.
v1 is for iMX8MQ and iMX8MM
v2 is for iMX8M Nano (iMX8MN)
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
No ROM INFO structure on iMX8MN, use new ROM API to get boot device
from ROM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN has its own get_boot_device, so restrict with i.MX8MQ and
i.MX8MM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN support loading images with rom api, so we implement
reuse board_return_to_bootrom to let ROM loading images.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN follow same logic as i.MX8MM, so use spl_board_boot_device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add pin header for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN does not have LVTTL, it has a PE property
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN has similar architecture with i.MX8MM, so it could reuse
the clock code of i.MX8MM, but i.MX8MN has different CCM root
configurations, so need a separate root entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add a dummy cpu type and support get_cpu_rev for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8MN kconfig entry
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The power domain tree is not accepted by Linux Kernel upstream.
only a single pd node is used currently, as following:
pd: imx8qx-pd {
compatible = "fsl,imx8qm-scu-pd", "fsl,scu-pd";
#power-domain-cells = <1>;
};
So to migrate to use upstream linux dts, we also need a driver
to support this.
This patch is to support the new method, compared with legacy power
domain tree, it will be simpiler, because each device will
has resource id as power domain index, it will be directly passed
to scfw, and no need to let power domain build that tree. If multiple
power domain is needed, it is the dts node should has correctly power
domains entry added and sequence correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The current i.MX8 power domain driver is based on i.MX vendor
power domain tree which will retire later.
The Linux upstream use a single pd node for power domain driver,
and U-Boot will adopt that. When U-Boot i.MX8 dts synced with
Linux Kernel upstream and related driver ready, the legacy
driver will be removed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
clk and pinctrl will be get(probed) during each device probe,
we don't need to probe them in scu driver. Only need to bind the sub-nodes
(clk and iomuxc) of MU node with their drivers.
So drop the code to probe the clk/pinctrl, and this patch will make it
easy to add more subnodes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Make DM and non-DM code clear using below structure.
#if !CONFIG_IS_ENABLED(DM_MMC)
<non-DM_MMC code>
#else
<DM_MMC code>
#endif
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Drop redundant code for non-removable feature. "non-removable" property
has been read in mmc_of_parse().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Update this tool to use Python 3 to meet the 2020 deadline.
Unfortunately this introduces a test failure due to a problem in pylibfdt
on Python 3. I will investigate.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Drop the now-unused Python 2 code to keep code coverage at 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
