| Age | Commit message (Collapse) | Author |
|---|
|
The manual resolution in commit ec7023db wrongly removed functions
nand_init and nand_deselect from file drivers/mtd/nand/mxc_nand_spl.c.
Revert this removal.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Conflicts:
drivers/mtd/nand/mxc_nand_spl.c
include/configs/m28evk.h
|
|
|
|
Enable LCD output support on M28EVK.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Add basic LCD driver for i.MX233 and i.MX28. This driver allows framebuffer
console and framebuffer logo.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Extend the regs-lcdif.h with registers for i.MX233.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
This function turns on the LCDIF clock and configures it's frequency. The
dividers settings are calculated within the function and the current
implementation should be fast and accurate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
MUX2_CTR is on GPIO1[5], not GPIO2[5], and it needs to be set high in order to
connect the FEC.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
All these macros are completely unused by any code.
CONFIG_FPGA is not a bitfield anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Ensure that wrong bitstream won't be loaded
to current device.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
There is no reason to include net.h header in fpga code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
All fpga functions use devnum as int. Only fpga_loadbitstream
is using it as unsinged long dev.
This patch synchronize it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
In bitstream decoding you can directly check device
which you want to load and in fpga.c are fpga_validate
and fpga_dev_info functions which should be used for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
CONFIG_FPGA in past was a bitfield where bits
were use for vendor identification.
This fix should be the part of this commit:
"Improve configuration of FPGA subsystem"
(sha1: 0133502e39ff89b67c26cb4015e0e7e8d9571184)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
The u-boot-imx23.bd and u-boot-imx28.bd need to be preprocessed, otherwise
they have issues with out-of-tree build where elftosb tool couldn't sometimes
find the u-boot.bin and spl/u-boot-spl.bin .
Preprocess these .bd files with sed and insert full path to u-boot.bin and
spl/u-boot-spl.bin to prevent this issue. Moreover, to avoid adding more
churn into main Makefile, move all this preprocessing and u-boot.sb generation
into CPU directory instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
The VDDMEM ramped up in very weird way as it was horribly misconfigured.
Instead of setting up VDDMEM in one swipe, let it rise slowly the same
way as VDDD and VDDA in spl_power_init.c and then only clear ILIMIT before
memory gets inited. This makes sure the VDDMEM rises sanely, not jumps up
and down as it did till now.
The VDDMEM prior to this change did this:
2V0____ .--------2V5
| `--'
0V____|
The VDDMEM now does this:
2V0_____,-----------2V5
/
0V__|
Moreover, VDDIO on MX23 uses 25mV steps while MX28 uses 50mV steps,
fix this difference too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Put an explanation in the source code as to why some DDR registers do not
need to be configured.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
mx23 SSP pad registers do not contain voltage selection bit, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
mx23 SSP pad registers do not contain voltage selection bit, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
After the recent fixes in the mx23 DDR setup, it is safe to operate DDR voltage
at the recommended 2.5V voltage level again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Use Samsung S3CA410X01 companion chip to reset PDA.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
|
|
This commit allows pxa2xx based boards to reimplement reset_cpu()
function with board specific reset sequence.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
|
|
This patch adds a driver for the diskonchip G4 nand flash device. It is based
on the driver from the linux kernel.
This also includes a separate SPL driver. A separate SPL driver is used because
the device operates in a different mode (reliable mode) when loading a boot
image, and also because the storage format of the boot image is different from
normal data (pages are stored redundantly). The SPL driver basically mimics how
a typical IPL reads data from the device. The special operating mode and
storage format are used to compensate for the fact that the IPL does not contain
the BCH ecc decoding algorithm (due to size constraints). Although the u-boot
SPL *could* use ecc, it operates like an IPL for the sake of simplicity and
uniformity, since the IPL and SPL share the task of loading the u-boot image.
As a side benefit, the SPL driver is very small.
[port from linux kernel 3.4 commit 570469f3bde7f71cc1ece07a18d54a05b6a8775d]
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
|
|
If CONFIG_USB_DEV_PULLUP_GPIO is defined, a link error occurs because the
set_GPIO_mode() helper function is not implemented. This function doesn't do
much except make the code a little more readable, so I just manually coded its
equivalent and removed the prototype from the header file. It is invoked no
where else in the code.
While I was at it, I noticed that two other function prototypes in the same
header file are also neither implemented nor invoked anywhere, so I removed them
as well.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
|
|
Make lcd_init() a weak pointer so that boards can overload it if necessary. The
palmtreo680 board needs to wiggle some gpios and configure the pwm controller in
order to get the lcd and its backlight working.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
|
|
This adds the definitions required to support the LCD device on the Palm Treo
680.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
|
|
This patch adds the bitrev library from the linux kernel. This is a simple
algorithm that uses an 8 bit look-up table to reverse the bits in data types of
8, 16, or 32 bit widths. The docg4 nand flash driver uses it.
[port from linux kernel v3.9 commit 7ee32a6d30d1c8a3b7a07a6269da8f0a08662927]
[originally added: v2.6.20 by commit a5cfc1ec58a07074dacb6aa8c79eff864c966d12]
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
|
|
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
There is no change of behavior, except for the folloing line that has been
removed because the iomux mode was not set accordingly and the pad used for OTG
OC is not this one:
mxc_iomux_set_input(MX53_USBOH3_IPP_IND_OTG_OC_SELECT_INPUT, 1);
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX53. The content of the file is taken from Freescale's Linux kernel at
commit 4ab3715, plus the required changes to make it work in U-Boot.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Matt Sealey <matt@genesi-usa.com>
|
|
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Add missing definitions that are required by future changes.
By the way, make some cosmetic cleanup.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
In ALT1 mode, EIM_CS2 is GPIO2[27], not ESDHC1.CD. Hence, rename
MX51_PAD_EIM_CS2__SD1_CD to MX51_PAD_EIM_CS2__GPIO2_27.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
The signal connected from this pin to the PMIC is WDOG_B, i.e. ALT0 mode, not
ALT1 (which even corresponds to nothing).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
There is no change of behavior.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX35. The content of the file is taken from Linux kernel at commit
267dd34, plus the required changes to make it work in U-Boot.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
