summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2016-05-25arm64: Pine64: update FDT filesAndre Przywara
The originally committed .dts files for the Pine64 were from an early proof-of-concept version and should have never been committed upstream. Replace them with much more mature versions, which also use a different naming scheme. Please note that at this point there is at least one binding which has not been agreed upon, so this is subject to change. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25arm64: sunxi: adjust default load addressesAndre Przywara
As arm64 has slightly different expectations about load addresses, lets use a different set of default addresses for things like the kernel. As arm64 kernels don't come with a decompressor right now, reserve some more space for really big uncompressed kernels. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25Revert "sunxi: Reserve ATF memory space on A64"Andre Przywara
The ARM Trusted Firmware (ATF) code now lives in SRAM on the Pine64/A64, so we can claim the whole of DRAM for OS use. This reverts commit 3ffe39ed2b66af71c7271d0cef2a248b5bf7dfdb. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: Properly announce BOOT_DEVICE_BOARD as "FEL"Bernhard Nortmann
This addresses a cosmetic issue when booting a sunxi device over USB (FEL mode), where the SPL currently would just print "Trying to boot from ". The patch fixes that to properly read "Trying to boot from FEL". Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: Increase SPL header size to 64 bytes to avoid code corruptionSiarhei Siamashka
The current SPL header, created by the 'mksunxiboot' tool, has size 32 bytes. But the code in the boot ROM stores the information about the boot media at the offset 0x28 before passing control to the SPL. For example, when booting from the SD card, the magic number written by the boot ROM is 0. And when booting from the SPI flash, the magic number is 3. NAND and eMMC probably have their own special magic numbers too. Currently the corrupted byte is a part of one of the instructions in the reset vectors table: b reset ldr pc, _undefined_instruction ldr pc, _software_interrupt <- Corruption happens here ldr pc, _prefetch_abort ldr pc, _data_abort ldr pc, _not_used ldr pc, _irq ldr pc, _fiq In practice this does not cause any visible problems, but it's still better to fix it. As a bonus, the reported boot media type can be later used in the 'spl_boot_device' function, but this is out of the scope of this patch. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: power: add AXP809 supportChen-Yu Tsai
The A80 uses the AXP809 as its primary PMIC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: Implement poweroff support for axp818 pmicChen-Yu Tsai
Adds poweroff support for axp818 pmic. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: Enable AXP818 SW for Sinovoip BPI M3Chen-Yu Tsai
The SW output of the PMIC supplies the ethernet PHY with power. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: power: axp818: Add support for switch SWChen-Yu Tsai
The AXP818 has a switchable output, SW. This is commonly used for controlling power to the LCD backlight. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25power: axp818: Fix typo for fldo2 Kconfig descriptionChen-Yu Tsai
Description said eldo2 instead of fldo2, a copy-paste error. Fixes: 38491d9c6515 ("power: axp818: Add support for FLDOs") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25power: axp221: Remove switch case to simplify axp_set_eldoChen-Yu Tsai
The ELDO enable bits and registers are contiguous for axp221. Instead of a switch case testing against the index, just use the index to shift the bit or register offset. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: Disable VIDEO for SoCs without display supportChen-Yu Tsai
The newer chips use a newer display pipeline, which is not supported. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: Add default MMC0 card detect pin for A83T, H3 and A64 SoCsChen-Yu Tsai
A83T, H3, and A64 have a dedicated pin for card detect on the PF pingroup. This is used in all designs. Set it as the default. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: Sort SoC variants by family (sunXi) first, chip name secondChen-Yu Tsai
In most other places, we sort SoC descriptions by family (sunXi) first, then by the chip name (A20). Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25sunxi: make SoC variant choice mandatoryChen-Yu Tsai
The user should always select an SoC variant to support. Not choosing one doesn't make sense for a bootloader. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: drivers/net/zynq_gem.c
2016-05-24net: phy: dp83867: Add SGMII helper for configurationDan Murphy
The code assumed that if the interface is not RGMII configured then it must be SGMII configured. This device has the ability to support most of the MII interfaces. Therefore add the helper for SGMII and only configure the device if the interface is configured for SGMII. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Add phy_interface_is_sgmii to phy.hDan Murphy
Add a helper to phy.h to identify whether the phy is configured for SGMII all variables. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Move is_rgmii helper to phy.hDan Murphy
Move the phy_interface_is_rgmii to the phy.h file for all phy's to be able to use the API. This now aligns with the Linux kernel based on commit e463d88c36d42211aa72ed76d32fb8bf37820ef1 Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: ti: Allow the driver to be more configurableDan Murphy
Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default. If devicetree is not used then use the default defines within the driver. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: dp83867: Add device tree bindings and documentationDan Murphy
Add the device tree bindings and the accompanying documentation for the TI DP83867 Giga bit ethernet phy driver. The original document was from: [commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel] Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: zynq_gem: Add the passing of the phy-handle nodeDan Murphy
Add the ability to pass the phy-handle node offset to the phy driver. This allows the phy driver to access the DT subnode's data and parse accordingly. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: Add reading of DT phy-handle nodeDan Murphy
Add the ability to read the phy-handle node of the cpsw slave. Upon reading this handle the phy-id can be stored based on the reg node in the DT. The phy-handle also needs to be stored and passed to the phy to access any phy data that is available. Signed-off-by: Dan Murphy <dmurphy@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: dra74_evm: enable eth driver modelMugunthan V N
Enable eth driver model for dra74_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: am437x_sk_evm: enable eth driver modelMugunthan V N
Enable eth driver model for am437x_sk_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24defconfig: am437x_gp_evm: enable eth driver modelMugunthan V N
Enable eth driver model for am437x_gp_evm as cpsw supports driver model. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: dra7: fix ethernet name with proper device addressMugunthan V N
Fix typo error for cpsw device name with proper device address Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: dra7: add syscon node to cpsw to read mac addressMugunthan V N
Add syscon node to cpsw device node to read mac address from efuse. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24arm: dts: am4372: add syscon node to cpsw to read mac addressMugunthan V N
Add syscon node to cpsw device node to read mac address from efuse. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: add support for reading mac address from efuseMugunthan V N
Different TI platforms has to read with different combination to get the mac address from efuse. So add support to read mac address based on machine/device compatibles. The code is taken from Linux drivers/net/ethernet/ti/cpsw-common.c done by Tony Lindgren. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: fix get mdio base and gmii_sel reg from DTMugunthan V N
Since dra7x platforms address bus is define as 64 bits to support LAPE, fdtdec_get_addr() returns a invalid address for mdio based and gmii_sel register address. Fixing this by using fdtdec_get_addr_size_auto_noparent() which will derive address cell and size cell from its parent. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24ARM: omap5: add platform specific ethernet phy modes configurationsMugunthan V N
Add platforms specific phy mode configuration bits to be used to configure phy mode in control module. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: net: cpsw: fix cpsw dp parse when num slaves as 1Mugunthan V N
On some boards number of slaves can be 1 when only one port ethernet is pinned out. So do not break when slave_index and num slaves check fails, instead continue to parse the next child. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24ti_omap5_common: eth: do not define DM_ETH for splMugunthan V N
Since omap's spl doesn't support DM currently, do not define DM_ETH for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24drivers: core: device: add support to check dt compatible for a device/machineMugunthan V N
Provide an api to check whether the given device or machine is compatible with the given compat string which helps in making decisions in drivers based on device or machine compatible. Idea taken from Linux. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: phy: Add PHY driver for mv88e61xx switchesKevin Smith
The previous mv88e61xx driver was a driver for configuring the switch, but did not integrate with the PHY/networking system, so it could not be used as a PHY by U-boot. This is a complete rework to support this device as a PHY. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24net: Remove unused mv88e61xx switch driverKevin Smith
No boards are using this driver. Remove in preparation for a new driver with integrated PHY support. Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de>
2016-05-24Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2016-05-24ARM: zynq: Simplify zynq configurationMichal Simek
Extending Kconfig for adding new platform is a lot of work for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and remove all dependencies on TARGET_ZYNQ_* options including SPL. As a side-effect it also remove custom init folder for ps7_init_gpl.* files. Folder is chosen based on device-tree file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24phy: marvell: Do not reset phy after negotiationMichal Simek
The patch "net: phy: do not read configuration register on reset" (sha1: a058052c358c3ecf5f394ff37def6a45eb26768c) was causing regression on zynq zc702 board where Marwell 88e1118 phy was resetted after negotiation was setup. Phy reset is done pretty early in phy_connect_dev() and doens't need to be called again in phy code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24phy: Wire return value from phy_config()Michal Simek
Fix zynq_gem driver to handle error from phy_config correctly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24image: Add boot_get_fpga() to load fpga with bootmMichal Simek
Add function boot_get_fpga() which find and load bitstream to programmable logic if fpga entry is present. Function is supported on Xilinx devices for full and partial bitstreams in BIN and BIT format. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Remove additional blankline in image.h
2016-05-24net: phy: Handle phy_startup() error codes properlyMichal Simek
Propagate error code from genphy_update_link() to phy startup(). Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24phy: Return correct error code when timeout happensMichal Simek
Return -ETIMEDOUT if timeout happens. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24net: xilinx: Handle error value from phy_startup()Michal Simek
Handle error returned by phy_startup() properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2016-05-24mkimage: Report information about fpgaMichal Simek
Add FIT_FPGA_PROP that user can identify an optional entry for fpga. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-24fpga: Fix typo in function commentMichal Simek
Trivial patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24ARM64: zynqmp: Enable CLK frameworkMichal Simek
ZynqMP is using fixed clocks now that's why enabling it to be available for drivers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2024-12-24 12:20:33 +0000