summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2007-08-10fdt: do board setup based on fdt address specified on bootm lineKim Phillips
The last fdt patch to bootm did board setup based on the address specified by a prior fdt address command invocation. The bootm code, as its call to fdt_chosen does, should use the fdt specified by the user on the bootm command. Note this restores full functionality for the 8360's existing default boot environment values, e.g. 'run nfsboot' (i.e. no having to 'fdt addr $fdtaddr' before booting a kernel). Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-10Call ft_board_setup() from the bootm command.Gerald Van Baren
In the patch titled "Create new fdt boardsetup command..." I removed the call to ft_board_setup() from the routine fdt_chosen(), but I forgot to add a direct call back into cmd_bootm.c This fixes the oversight by adding the direct call to the bootm command. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Create new fdt boardsetup command, fix bug parsing [] form of set values.Gerald Van Baren
Previously ft_board_setup() was called by fdt_chosen() which was not really correctly structured. This splits ft_board_setup() out by creating a new fdt boardsetup command. Fix a bug when parsing fdt set command values which have the square bracket form [00 11 22 33] - the length was updated incorrectly in when parsing that form. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Tighten up the error messages.Gerald Van Baren
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Asthetic improvements: error messages and line lengths.Gerald Van Baren
Tighten up the error messages, split overlength lines. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Fix fdt_chosen() to call ft_board_setup(), clean up long lines.Gerald Van Baren
The fdt_chosen() function was adding/seting some properties ad-hoc improperly and duplicated (poorly) what was done in ft_board_setup() Clean up long lines (setting properties, printing errors). Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10For fdt_find_node_by_path(), handle the root path properly.Gerald Van Baren
Also removes the special case root path detection in cmd_fdt.c since it is no longer necessary. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Add fdt_find_node_by_type() and fdt_find_compatible_node() to LIBFDTGerald Van Baren
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Replace fdt_node_offset() with fdt_find_node_by_path().Gerald Van Baren
The new name matches more closely the kernel's name, which is also a much better description. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Fix cmd_fdt line lengths, refactor code.Gerald Van Baren
Break lines that were greater than 80 characters in length. Move the fdt print and property parsing code to separate static functions to reduce coding clutter in the fdt_cmd handling body. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10FDT command improvements.Gerald Van Baren
Fix "fdt set" so that it will create a non-existing property. Add "fdt mknode" to create nodes. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Reorganize and fix problems (returns) in the bootm command.Gerald Van Baren
Do *NOT* return after the "point of no return" has been passed. If something goes wrong, the board must be reset after that point. Move the "Transferring control to Linux" debug message back to where it belongs: just before transferring control to linux. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Fix bugs in the CONFIG_OF_LIBFDTGerald Van Baren
Stupid coding mistakes (identified by Timur Tabi, thanks). Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Improve fdt move length handling.Gerald Van Baren
Make the length parameter optional: if not specified, do the move using the current size unchanged. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Minor code clean up.Gerald Van Baren
Declare the variable fdt properly as extern. Call the "set_fn" function pointer the "short way" without the full dereferencing syntax. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Improve error messages, more informative.Gerald Van Baren
Print more than the raw libfdt error message strings. This is especially useful for cluing in the user when the bootm command aborts due to blob problems. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10libfdt: Conditionally compile based on CONFIG_OF_LIBFDTGerald Van Baren
This is the way u-boot reduces configured-out code. At Wolfgang Grandegger and Wolfgang Denk's request, make libfdt conform. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2007-08-10Merge git://www.denx.de/git/u-bootGerald Van Baren
2007-08-11add image size and descriptors for Spartan 3E FPGA chipsBruce Adler
Spartan 3E image sizes taken from Table 1-4 in Xilinx UG332 (v1.1) Signed-off by: Bruce Adler <bruce.adler@ccpu.com>
2007-08-10make MAKEALL more immune to merge conflictsKim Phillips
..by placing board entries one per line, as suggested by jdl. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-10README: Remove outdated cpu type, board type, and NAME_config listsKim Phillips
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-10mpc83xx: Suppress the warning 'burstlen'Dave Liu
suppress the warning 'burstlen' of spd_sdram. Signed-off-by: Dave Liu <daveliu@freescale.com>
2007-08-10Add support for SBC8641D. Config files.Joe Hamman
Add support for Wind River's SBC8641D reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com> Acked-by: Wolfgang Denk <wd@denx.de> Acked-by: Jon Loeliger <jdl@freescale.com>
2007-08-10Add support for SBC8641D. Board files.Joe Hamman
Add support for Wind River's SBC8641D reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com> Acked-by: Wolfgang Denk <wd@denx.de> Acked-by: Jon Loeliger <jdl@freescale.com>
2007-08-10Merge with git+ssh://sr@pollux.denx.org/home/wd/git/u-boot/from_stefanStefan Roese
2007-08-10Conding style cleanupStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-10Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-08-10[ARM] TI DaVinci support, hopefully finalSergey Kubushyn
Add support for the following DaVinci boards: - DV_EVM - SCHMOOGIE - SONATA Changes: - Split into separate board directories - Removed changes to MTD_DEBUG (or whatever it's called) - New CONFIG_CMD party line followed - Some cosmetic fixes, cleanup etc. - Patches against the latest U-Boot tree as of now. - Fixed CONFIG_CMD_NET in net files. - Fixed CONFIG_CMD_EEPROM for schmoogie. - Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and DV_EVM. Can't check if it works on SONATA, don't have a board any more, but it at least compiles. Here is an excerpt from session log on SCHMOOGIE... U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17) DRAM: 128 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock : 297MHz DDR Clock : 162MHz ETH PHY : DP83848 @ 0x01 U-Boot > iprobe Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F U-Boot > ping 192.168.253.10 host 192.168.253.10 is alive U-Boot > Signed-off-by: Sergey Kubushyn <ksi@koi8.net> Acked-by: Dirk Behme <dirk.behme@gmail.com> Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com> Acked-by: Stefan Roese <sr@denx.de>
2007-08-10fsl_pci_init cleanup.Ed Swarthout
Do not enable normal errors created during probe (master abort, perr, and pcie Invalid Configuration access). Add CONFIG_PCI_NOSCAN board option to prevent bus scan. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
2007-08-10pciauto_setup_device bars_num fixEd Swarthout
Passing bars_num=0 to pciauto_setup_device should assign no bars. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com> Acked-by: Andy Fleming <afleming@freescale.com>
2007-08-108641hpcn: Do correct sized pointer math.Jon Loeliger
When I rebased Ed's patch and cleaned up a few compilation problems, I apparently rebased my brain on crack first. Fix that by doing (char *) sized pointer math as needed. Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-08-10cpu/86xx fixes.Jon Loeliger
Remove rev 1 fixes. Always set PICGCR_MODE. Enable machine check and provide board config option to set and handle SoC error interrupts. Include MSSSR0 in error message. Isolate a RAMBOOT bit of code with #ifdef CFG_RAMBOOT. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-08-10Coding style cleanupStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-10Merge with git+ssh://atlas/home/wd/git/u-boot/masterWolfgang Denk
2007-08-10Merge with /home/wd/git/u-boot/workWolfgang Denk
2007-08-10Make use of generic 64bit division in nand_util.cDirk Behme
Use generic 64bit division in nand_util.c. This makes nand_util.c independent of any toolchain 64bit division. Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
2007-08-10Move 64bit division from avr32 to generic libDirk Behme
Move the 64bit division from lib_avr32 to lib_generic. With this, all boards can do_div/__div64_32 if needed, not only avr one. Code is put to lib_generic, so no larger memory footprint if not used. No code modifications. Thanks for proposal by Håvard Skinnemoen. Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: HCU5 filesNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: HCU4 filesNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: common filesNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: make relatedNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: HCU5 configNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: HCU4 configNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: READMEsNiklaus Giger
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10Add PPC4xx-HCU4 and HCU5 boards: InfrastructureNiklaus Giger
This series of patches adds support for 2 boards from Netstal Maschinen. The HCU4 has a PPC405Gpr and the HCU5 has a PPC440EPX. The HCU4 has a somehow complicated flash setup, as the booteprom is only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more elegant solution. The HCU5 has only a booteprom as the whole code will be downloaded from a different board which has HD, CD-ROM, etc and where all code is stored. This is my third try. I incorporated all suggestions made by Wolfgang and Stefan. Thanks them a lot. Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2007-08-10ppc4xx: Update lwmon5 POST configurationStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-10POST: Add ppc4xx UART POST support without external uart clock (lwmon5)Yuri Tikhonov
The patch adds support for UART POST on ppc44x-based boards with no external serial clocks installed. Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Acked-by: Stefan Roese <sr@denx.de>
2007-08-10mpc83xx: fix ITX[GP] O=builddir buildsKim Phillips
make: *** No rule to make target `/work/wd/tmp/board/mpc8349itx/u-boot.lds', needed by `/work/wd/tmp/u-boot'. Stop. Both the ITX and ITX-GP fail when you use "make O=<some dir> ..." or "BUILD_DIR=<some dir> ./MAKEALL ..." Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-10mpc83xx: Correct the README for DDR ECCDave Liu
Update the README for DDR ECC, change the name to README.mpc83xx.ddrecc. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-10mpc83xx: Consolidate the ECC support of 83xxDave Liu
Remove the duplicated source code of ecc command on the <board>.c, for reused, move these code to cpu/mpc83xx directory. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
generated by cgit (git 2.34.1) at 2025-01-09 06:44:26 +0000