summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-01Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
Minor fixes for the Alt board and PHY use on Gen2.
2019-04-01Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- clk: sunxi: a10: Add CLK_AHB_GMAC
2019-04-01clk: sunxi: a10: Add CLK_AHB_GMACJagan Teki
CLK_AHB_GMAC was suppose to be part of previous commit "clk: sunxi: Implement A10 EMAC clocks" add it so-that we can get rid of sunxi_set_gate warning on boot message. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-01Merge tag 'u-boot-imx-20190401' of git://git.denx.de/u-boot-imxTom Rini
Fixes for 2019.01 - pico-imx6ul: fix after conversion - engicam boards - pico-imx7d _ README due to hang with imx-usb-loader
2019-03-31pico-imx7d: README: Recommend the usage of a USB hubFabio Estevam
Since commit 9e3c0174da842 ("pico-imx7d: Add LCD support") we started to notice some hangs in U-Boot. There is not an issue on such commit per se, but due to the LCD support the current drawn is increased and this may cause issues when powering pico-imx7d-pi from USB. Some computers may be a bit strict with USB current draw and will shut down their ports if the draw is too high. The solution for that is to use an externally powered USB hub between the board and the host computer. Add such recommendation to the README file. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-03-31configs: icorem6: Use imx6 cratch register for bootcountJagan Teki
SRAM address used for bootcount on exiting code is erasing previous count value when system reset from Linux. So use the dedicated imx6 scratch register, GPR2 to preserve the contents even if the system reset from Linux. Fixes: 4eb9aa39350e ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter") Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2019-03-31configs: icore: Fix U-Boot proper loading from nandMichael Trimarchi
SPL on Engicam i.Core M6 boards enabled DM, so it would require some malloc() pool before relocation in order to load U-Boot proper properly. So, enable SPL malloc() pool of 0x2000 size similarly like what we have used for icore mmc defconfigs. Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-03-31ARM: imx6q_logic: Enable UUID supportAdam Ford
With UUID support, the root can now point to UUID. This makes swiching between mmc 0 and mmc 1 easier by simplying changing mmcdev between 0 and 1. From there, the scripts handle the rest. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-03-31pico-imx6ul: Fix eMMC boot after DM_MMC conversionFabio Estevam
After the DM_MMC conversion the following eMMC boot error is observed: U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000) Trying to boot from MMC1 MMC Device 0 not found spl: could not find mmc device 0. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### This happens because the SPL code does not initialize the SDHC pins and clock. Fix it by moving the original eMMC initialization from U-Boot proper to SPL. Reported-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-03-31Merge branch 'master' of git://git.denx.de/u-bootStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-03-31Merge tag 'video-fixes-for-2019.04-rc4' of git://git.denx.de/u-boot-videoTom Rini
sunxi HDMI clock fix
2019-03-31Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchipTom Rini
Last-minute fixes for Rockchip for 2019.04: - reverts the deprecation of the 'download-key' detection (with a full solution pending for the next release) - applies a temporary fix for the 32bit pinctrl registers on the RK3288
2019-03-31dfu: usb: Update MAINTAINERS file regarding DFU/USB gadget supportLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-03-30ARM: rmobile: alt: Fix I2C bus numberMarek Vasut
The I2C bus number to access the PMIC is I2C 7, fix this. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-30ARM: dts: rmobile: Activate I2C7 on AltMarek Vasut
Activate I2C7 on Alt to allow access to the PMIC. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-30ARM: rmobile: rcar-gen2: Activate bootm_sizeMarek Vasut
Commit d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size") only fixed the superfluous CONFIG_SYS_BOOTMAPSZ for R-Car Gen3, even though it listed all affected boards. Apply the same fix to Gen2. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Fixes: d245059ff797 ("ARM: rmobile: rcar-gen3: Activate bootm_size") Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
2019-03-30ARM: rmobile: Fix PHY LED mode register maskMarek Vasut
The PHY LED mode register mask should be 0xc000 , not 0xc0000. Correct the mask to operate on the right bits. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-30ARM: rmobile: alt: Synchronize defconfigMarek Vasut
Synchronize the R8A7794 Alt defconfig, enable DM SPI, DM SPI FLASH and I2C driver support. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-30ARM: rmobile: alt: Remove CLK2MHZ macroMarek Vasut
The CLK2MHZ macro is unused, remove it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-30ARM: rmobile: alt: Remove R8A7794_ETHERNET_BMarek Vasut
The R8A7794_ETHERNET_B config option is unused and based on the description, this is a setting which should be fully done on a DT level instead. Remove this config option. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-29Merge branch '2019-03-29-master-imports'Tom Rini
- Bugfixes: - mmc: correct the HS400 initialization process - configs: ti: Move FIT image load address to avoid overwrite - lib: time: update module enable MACRO - Add mbrugger as RPi board maintainer, correct agraf's email address.
2019-03-29lib: time: update module enable MACROKever Yang
We'd better use correct way to check if module has enabled. for we have 3 timer MACRO: - CONFIG_TIMER - CONFIG_SPL_TIMER - CONFIG_TPL_TIMER Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-03-29doc/git-mailrc: correct entry 'agraf'Heinrich Schuchardt
Correct Alex's email address. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Alexander Graf <agraf@csgraf.de>
2019-03-29RPi: Add mbrugger as board maintainerMatthias Brugger
I took over maintainership from Alex Graf with commit 3157bbfa18 ("rpi: Make Matthias maintainer") But I forgot to update the board maintainer file. This patch adds myself to the game. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Alexander Graf <agraf@csgraf.de>
2019-03-29configs: ti: Move FIT image load address to avoid overwriteAndrew F. Davis
The FIT image is loaded to 0x8700_0000 followed by extracting from that several large images also into the 0x8x00_0000 range. Large images can end up overwriting the FIT image as it is being extracted from. Move the FIT load address clear out to 0x9000_0000, this will require a board to have at least 256MB of DRAM, if less then more careful planning will be required for that platform. Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-03-29mmc: correct the HS400 initialization processBOUGH CHEN
After the commit b9a2a0e2e9c0 ("mmc: Add support for downgrading HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed() which indicates that the HS200/HS400 to HS downgrade is happening. During the HS400 initialization, first select to HS200, and config the related clock rate, then downgrade to HS mode. So here also need to config the downgrade value to be true for two reasons. First, make sure in the function mmc_set_card_speed(), after switch to HS mode, first config the clock rate, then read the EXT_CSD, avoid receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue the MMC_CMD_SWITCH command, it need to wait a bit then switch bus properties. Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer mode in this case, and USDHC will never get data transfer complete status, cause the uboot hang. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
2019-03-29Merge tag 'efi-2019-04-rc5-2' of git://git.denx.de/u-boot-efiTom Rini
Pull request for UEFI system for v2019.04-rc5-2 This patch series contains a bug fix for a double free in a UEFI unit test. The other patches are documentation only (except for the definition of two additional constants).
2019-03-29pinctrl: rockchip: Add 32bit writing function for rk3288 gpio0 pinctrlDavid Wu
There are no higher 16 writing corresponding bits for pmu_gpio0's iomux/drive/pull at rk3288, need to read the value from register firstly. Add the flag to distinguish it from normal registers. Signed-off-by: David Wu <david.wu@rock-chips.com>
2019-03-29Revert "rockchip: Drop call to rockchip_dnl_mode_check() for now"Philipp Tomsich
Due to a final resolution not coming up in time for 2019.04 and following the consensus on the discussion, we'll keep this around for 2019.04 after all. This reverts commit 0d968ceb1ff63b0d220a571f438f0d5fe6350e88.
2019-03-28Merge tag 'arc-last-minute-for-2019.04' of git://git.denx.de/u-boot-arcTom Rini
This is last minute change which fixes problems in runtime on AXS10x board caused by some changes in NAND framework and tiny documentation improvement. Anyways NAND flash storage was never really used on the board for various reasons and now we decided to drop it for good. Note this change only touches 1 ARC board so that should be safe for others. As usual - build tested in TravisCI, see https://travis-ci.org/abrodkin/u-boot/builds/512041342
2019-03-28sunxi: video: HDMI: Fix clock setupJernej Skrabec
Currently, HDMI driver doesn't consider minimum and maximum allowed rate of pll3 (video PLL). It works most of the time, but not always. Consider monitor with resolution 1920x1200, which has pixel clock rate of 154 MHz. Current code would determine that pll3 rate has to be set to 154 MHz. However, minimum supported rate is 192 MHz. In this case video output just won't work. The reason why the driver is written in the way it is, is that at the time HDMI PHY and clock configuration wasn't fully understood. But now we have needed knowledge, so the issue can be fixed. With this fix, clock configuration routine uses full range (1-16) for clock divider instead of limited one (1, 2, 4, 11). It also considers minimum and maximum allowed rate for pll3. Fixes: 56009451d843 ("sunxi: video: Add A64/H3/H5 HDMI driver") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-03-28hsdk: readme: Suggest getting pyelftools with pipAlexey Brodkin
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Suggested-by: Yunir Salimzyanov <yunir@synopsys.com>
2019-03-28ARC: AXS10x: drop NAND supportEugeniy Paltsev
On AXS10x boards we have non-standard NAND controller which was never really used a lot as there're other much more convenient [as they are standard & removable] persistent media like SD-card and USB mass storage. Moreover after recent changes we face with some NAND controller runtime issues. So instead of keeping support of yet another non-standard peripheral we're dropping its support for good. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-03-28efi_loader: define development target in README.uefiHeinrich Schuchardt
Describe the target scope of the UEFI implementation in U-Boot. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-03-27efi_loader: update TODOs in doc/README.uefiHeinrich Schuchardt
The following TODOs are closed: - GetNextVariableName is not implemented - event groups - manage events in a linked list Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-03-27MAINTAINERS: adjust git repository for EFI PAYLOADHeinrich Schuchardt
The EFI PAYLOAD will use git://git.denx.de/u-boot-efi.git in future. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-03-27efi_loader: TODO for the EFI file protocolHeinrich Schuchardt
We currently only support EFI_FILE_PROTOCOL_REVISION while UEFI specs 2.4 - 2.7 prescribe EFI_FILE_PROTOCOL_REVISION2. Add a todo. Add missing constants for the EFI file protocol revision. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-03-27efi_selftest: avoid double free in dp utilities testHeinrich Schuchardt
Avoid duplicate FreePool() in unit test for the device patch utilities protocol. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-03-26Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- configs: Stratix10: Remove CONFIG_USE_TINY_PRINTF
2019-03-26Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Various fixes for bugs found by u-boot test.py
2019-03-26Merge branch '2019-03-25-master-imports'Tom Rini
- Convert various SPI related options to Kconfig
2019-03-25Convert CONFIG_ENV_SPI_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25Convert CONFIG_DEFAULT_SPI_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_DEFAULT_SPI_BUS CONFIG_DEFAULT_SPI_MODE Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25Convert CONFIG_SF_DEFAULT_* to KconfigPatrick Delaunay
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25tqma6s_wru4_mmc: manage board_spi_cs_gpio correctlyPatrick Delaunay
Define the function board_spi_cs_gpio only when needed, only called in drivers/spi/mxc_spi.c. That avoid compilation issue for tqma6s_wru4_mmc_defconfig when CONFIG_SF_DEFAULT_BUS and CONFIG_SF_DEFAULT_CS are not defined (CMD_SF not defined) after migration in KConfig. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25exynos: replace CONFIG_ENV_SPI_BASE by CONFIG_SYS_SPI_BASEPatrick Delaunay
Replace CONFIG_ENV_SPI_BASE by the better CONFIG_SYS_SPI_BASE (it is not the location for environment but the location for U-Boot) and, as it is the only platform with use this define, remove it from whitelist. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25controlcenterdc: move some configuration in defconfig filePatrick Delaunay
Move some configurations in defconfig file - CONFIG_CMD_I2C - CONFIG_CMD_SPI This allow correct dependency handling in Kconfig. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25bcm7445: move some configuration in defconfig filePatrick Delaunay
Move some configurations in defconfig file - CONFIG_DM_SPI (removed by syncing defconfigs ) - CONFIG_CMD_SF - CONFIG_CMD_SPI - CONFIG_CMD_SF_TEST This allow correct dependency handling in Kconfig. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25Merge branch '2019-03-25-master-imports'Tom Rini
- 3 bugfixes: - mmc: Align MMC_TRACE with tiny printf - scripts/Makefile.extrawarn: Silence more DTC warnings - rsa: check that pointer checksum isn't NULL before using it
2019-03-25mmc: tmio: Clamp SD_SECCNT to 16bit values on 16bit IPMarek Vasut
On 16bit variants of the TMIO SD IP, the SECCNT register can only be programmed to 16bit values, while on the 32bit and 64bit variants it can be programmed to 32bit values. The SECCNT register indicates the maximum number of blocks in a continuous transfer. Hence, limit the maximum continuous transfer block count to 65535 blocks on 16bit variants of the TMIO IP and to BIT(32)-1 blocks on 32bit and 64bit variants. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit (git 2.34.1) at 2024-12-28 14:29:40 +0000