summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-09-11arm: dts: dra7: sync DT with latest LinuxLokesh Vutla
Sync all dra7* specific dts files with the upstream kernel including changes queued for 4.14 https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.14/dt-v3 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11env: ti: boot: Select dtb name for dra76Lokesh Vutla
Select dtb name for dra76-evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add support for powering on mmc ldoLokesh Vutla
ldo4 is used to poweron mmc on dra76-evm. Enable it. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add the pinmux dataLokesh Vutla
Adding pinmux and IODELAY data for dra76-evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add DDR dataLokesh Vutla
dra76-evm has the ddr parts connectedi running at 666MHz: EMIF1: MT41K512M16HA-125 AIT:A x 2 EMIF2: MT41K512M8RH-125-AAT:E x 4 Add support for configuring the above DDR parts. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add the pmic dataKeerthy
dra76-evm uses lp8736 and tps65917 pmic for powering on various peripherals. Add data for these pmics and register for dra76-evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11board: ti: dra76-evm: Add epprom supportLokesh Vutla
The dra76-evm is a board based on TI's DRA76 processor Add eeprom support Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11arm: dra76: Add support for ES1.0 detectionPraneeth Bajjuri
dra76 family is a high-performance, infotainment application device, based on OMAP architecture on a 28-nm technology. This contains most of the subsystems, peripherals that are available on dra74, dra72 family. This SoC mainly features Subsystems: - 2 x Cortex-A15 with max speed of 1.8GHz - 2 X DSP - 2 X Cortex-M4 IPU - ISS - CAL - DSS - VPE - VIP Connectivity peripherals: - 1 USB3.0 and 3 USB2.0 subsystems - 1 x SATA - 2 x PCI Express Gen2 - 3-port Gigabit ethernet switch - 2 x CAN - MCAN Adding CPU detection support for the dra76 ES1.0 soc and update prcm, control module, dplls data. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Praneeth Bajjuri <praneeth@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11arm: dra7: Kconfig: Select LP87565 related configsLokesh Vutla
LP87565 is present on dra76-evm. Select it for TARGET_DRA7XX_EVM. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11palmas: Add support for powering different ldosLokesh Vutla
It is not necessary that ldo1 is used to power on mmc. So, add support for passing ldo registers for powering on mmc. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11arm: omap5+: Add board specific ldo poweringLokesh Vutla
It is not necessary all omap5+ based uses the same PMIC to poweron mmc. So add support for enabling mmc based on board. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2017-09-11Prepare v2017.09Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-11MAINTAINERS: board: qcom: db410c: Maintainer changedJorge Ramirez-Ortiz
Replacing original author Mateusz Kulikowski <mateusz.kulikowski@gmail.com> as db410c maintainer Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-09-11armv8: fsl-layerscape: Add back L3 flushing for all exception levelsYork Sun
CCN-504 HPF registers were believed to be accessible only from EL3. However, recent tests proved otherwise. Remove checking for exception level to re-enable L3 cache flushing for all levels. Signed-off-by: York Sun <york.sun@nxp.com> Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
2017-09-11armv8: ls1088a: Enable PCIe in defconfigsHou Zhiqiang
Enabled PCIe support and PCI command feature. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: ls1088a: add PCIe dts nodeHou Zhiqiang
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: ls1088a: fix the MMU table for pcie config spaceHou Zhiqiang
The pcie config space of ls1088a is different from ls2080a. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: fsl-layerscape: Fix MC reserved memory calculationYork Sun
In case high region memory doesn't have enough space for Management Complex (MC), the return value should indicate a failure so the caller can handle it accordingly. Signed-off-by: York Sun <york.sun@nxp.com> Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
2017-09-11armv7: Add workaround for USB erratum A-009007Ran Wang
Rx Compliance tests may fail intermittently at high jitter frequencies using default register values Program register USB_PHY_RX_OVRD_IN_HI in certain sequence to make the Rx compliance test pass. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv7: Add workaround for USB erratum A-008997Ran Wang
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential Output Voltage Test Compliance fails using default transmitter settings Change config of transmitter signal swings by setting register PCSTXSWINGFULL to 0x47 to pass compliance tests. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv7: Add workaround for USB erratum A-009798Ran Wang
The default setting for USB High Speed Squelch Threshold results in a threshold close to or lower than 100mV. This leads to Receive Compliance test failure for a 100mV threshold. Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv7: Add workaround for USB erratum A-009008Ran Wang
USB High Speed (HS) EYE Height Adjustment USB HS speed eye diagram fails with the default value at many corners, particularly at a high temperature Optimal eye at TXREFTUNE value to 0x9 is observed, change set the same value. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: Add workaround for USB erratum A-009007Ran Wang
Rx Compliance tests may fail intermittently at high jitter frequencies using default register values. Program register USB_PHY_RX_OVRD_IN_HI in certain sequence to make the Rx compliance test pass. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: Add workaround for USB erratum A-008997Ran Wang
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential Output Voltage Test Compliance fails using default transmitter settings Change config of transmitter signal swings by setting register PCSTXSWINGFULL to 0x47 to pass compliance tests. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: Add workaround for USB erratum A-009798Ran Wang
The default setting for USB High Speed Squelch Threshold results in a threshold close to or lower than 100mV. This leads to Receiver Compliance test failure for a 100mV threshold. Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: Add workaround for USB erratum A-009008Ran Wang
USB High Speed (HS) EYE Height Adjustment USB HS speed eye diagram fails with the default value at many corners, particularly at a high temperature Optimal eye at TXREFTUNE value to 0x9 is observed, change set the same value. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: Add scfg_clrsetbits_32(), scfg_clrbits_32()Ran Wang
Some erratum patch might need it to program registers. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: ls1088aqds: Add support of EC1 and EC2Prabhakar Kushwaha
EC1 and EC2 are RGMII interface on ls1088aqds platform. This patch add support of RGMII with PHY and MDIO Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: fsl-layerscape: Support to add RGMII for ls1088aqdsAshish Kumar
This patch adds support for RGMII protocol NXP's LDPAA2 support RGMII protocol. LS1088A is the first Soc supporting both RGMII and SGMII. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: ls1088aqds: Add support of LS1088AQDSAshish Kumar
This patch add support of LS1088AQDS platform. The LS1088A QorIQTM Development System (QDS) is a high-performance computing, evaluation, and development platform that supports the LS1088A QorIQ Architecture processor. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: ls1088ardb: Add support for LS1088ARDB platformAshish Kumar
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin platform that supports the LS1088A family SoCs. This patch add basic support of the platform. Signed-off-by: Alison Wang <alison.wang@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> [YS: Disabled NAND in board header file] Reviewed-by: York Sun <york.sun@nxp.com> WIP: disable NAND for LS1088ARDB
2017-09-11armv8: ls1088a: Add NXP LS1088A SoC supportAshish Kumar
LS1088A is compliant with the Layerscape Chassis Generation 3 with eight ARM v8 Cortex-A53 cores in 2 cluster, CCI-400, one 64-bit DDR4 SDRAM memory controller with ECC, Data path acceleration architecture 2.0 (DPAA2), Ethernet interfaces (SGMIIs, RGMIIs, QSGMIIs, XFIs), QSPI, IFC, PCIe, SATA, USB, SDXC, DUARTs etc. Signed-off-by: Alison Wang <alison.wang@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> [YS: Revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: fsl-layerscape: Fix final MMU table for QSPI and IFCSuresh Gupta
For QSPI and IFC addresses execution shouldn't be allowed when u-boot running from DDR. Revise the MMU final table to enforce execute-never bits. Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: fsl: Use correct conditional compile for ls1012aRan Wang
According current code base, CONFIG_LS1012A should be CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be wrongly called to disable all dwc3 USB nodes on LS1012A, which cause Linux USB function stop working at all. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11drivers:net:fsl-mc: Update MC address calculationPriyanka Jain
Update MC address calculation as per MC design requirement of address as least significant 512MB address of MC private allocated memory, i.e. address should point to end address masked with 512MB offset in private DRAM block. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com> [YS: reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: fsl-lsch3: Make CCN-504 related code conditionalAshish Kumar
LS2080 family has CCN-504 cache coherent interconnet. Other SoCs in LSCH3 family may have differnt interconnect. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> [YS: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11spl: fit: Add booting OS firstYork Sun
If CONFIG_SPL_OS_BOOT is enabled, boot OS if kernel image is found in FIT structure. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11spl: fit: Support both external and embedded dataYork Sun
SPL supports U-Boot image in FIT format which has data outside of FIT structure. This adds support for embedded data for normal FIT images. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11spl: fit: Eanble GZIP support for image decompressionYork Sun
Add Kconfig option SPL_GZIP and SPL_ZLIB to enable gunzip support for SPL boot, eg. falcon boot compressed kernel image. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11cmd: spl: Fix compiling warningYork Sun
Fix warning "cast from pointer to integer of different size". Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11tools: pblimage: Fix address calculationYork Sun
The image size should be added to the initial pbl command, not bit "ORed". Signed-off-by: York Sun <york.sun@nxp.com>
2017-09-11armv8: LS2080ARDB: Add secure boot defconfig for QSPI boot.Udit Agarwal
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [YS: dropped redundant commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11LS2080ARDB: QSPI boot: Secure Boot image validationUdit Agarwal
Adds header address for PPA to be validated during ESBC phase for ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It must be initialized before the PPA. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [YS: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11SECURE_BOOT: Unify memory map for Layerscape based platformsSumit Garg
Unify memory map for Layerscape based platforms. This patch includes changes in bootscript, bootscript header and PPA header addresses change as per unified memory map. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11QE: Set QE_IRAM_READY after uploading firmwareZhao Qiang
QE_IRAM_READY should be set only after successfully uploading the firmware. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11fsl-layerscape: Consolidate registers space defination for CCI-400 busAshish Kumar
CoreLink Cache Coherent Interconnect (CCI) provides full cache coherency between two clusters of multi-core CPUs and I/O coherency for devices and I/O masters. This patch add new config option SYS_FSL_HAS_CCI400 and moves existing register space definaton of CCI-400 bus to fsl_immap to be shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET in Kconfig. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> [YS: revised commit message, squashed patches for armv8 and armv7] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11ipu_common: Let the MX6 IPU clock be calculated in run-timeFabio Estevam
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz. When running a SPL target, which supports multiple MX6 variants we cannot properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as such decision is done in build-time currently. Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be configured in run-time on mx6. Reported-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de> [agust: fixed #endif in cgtqmx6eval.h] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-09-10cmd: ide: Make the first device the default oneBin Meng
At present the IDE device number is initialized to -1, which means we cannot type "ide read" command before setting the device number via "ide device #". For convenience, let's set the first device as the default one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-10block: ide: Don't bother to create BLK device if no CDROM insertedBin Meng
When there is no CDROM inserted, the block size is zero hence there is no need to create a BLK device for it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-25 02:39:49 +0000