| Age | Commit message (Collapse) | Author |
|---|
|
The IVT offset is changed on i.MX8MN. Use ROM_VERSION to pass the
v1 or v2 to mkimage.
v1 is for iMX8MQ and iMX8MM
v2 is for iMX8M Nano (iMX8MN)
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
No ROM INFO structure on iMX8MN, use new ROM API to get boot device
from ROM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN has its own get_boot_device, so restrict with i.MX8MQ and
i.MX8MM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN support loading images with rom api, so we implement
reuse board_return_to_bootrom to let ROM loading images.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN follow same logic as i.MX8MM, so use spl_board_boot_device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add pin header for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN does not have LVTTL, it has a PE property
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MN has similar architecture with i.MX8MM, so it could reuse
the clock code of i.MX8MM, but i.MX8MN has different CCM root
configurations, so need a separate root entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add a dummy cpu type and support get_cpu_rev for i.MX8MN
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8MN kconfig entry
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The power domain tree is not accepted by Linux Kernel upstream.
only a single pd node is used currently, as following:
pd: imx8qx-pd {
compatible = "fsl,imx8qm-scu-pd", "fsl,scu-pd";
#power-domain-cells = <1>;
};
So to migrate to use upstream linux dts, we also need a driver
to support this.
This patch is to support the new method, compared with legacy power
domain tree, it will be simpiler, because each device will
has resource id as power domain index, it will be directly passed
to scfw, and no need to let power domain build that tree. If multiple
power domain is needed, it is the dts node should has correctly power
domains entry added and sequence correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The current i.MX8 power domain driver is based on i.MX vendor
power domain tree which will retire later.
The Linux upstream use a single pd node for power domain driver,
and U-Boot will adopt that. When U-Boot i.MX8 dts synced with
Linux Kernel upstream and related driver ready, the legacy
driver will be removed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
clk and pinctrl will be get(probed) during each device probe,
we don't need to probe them in scu driver. Only need to bind the sub-nodes
(clk and iomuxc) of MU node with their drivers.
So drop the code to probe the clk/pinctrl, and this patch will make it
easy to add more subnodes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Make DM and non-DM code clear using below structure.
#if !CONFIG_IS_ENABLED(DM_MMC)
<non-DM_MMC code>
#else
<DM_MMC code>
#endif
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Drop redundant code for non-removable feature. "non-removable" property
has been read in mmc_of_parse().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
|
|
Update this tool to use Python 3 to meet the 2020 deadline.
Unfortunately this introduces a test failure due to a problem in pylibfdt
on Python 3. I will investigate.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Drop the now-unused Python 2 code to keep code coverage at 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Some tests have crept in with Python 2 strings and constructs. Convert
then.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When preparing to possible expand or contract an entry we reset the size
to the original value from the binman device-tree definition, which is
often None.
This causes binman to forget the original size of the entry. Remember this
so that it can be used when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This function should use a void * type, not char *. This causes an error:
TypeError: in method 'fdt_property_stub', argument 3 of type 'char const *'
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Sync up the libfdt Python bindings with upstream, commit:
430419c (tests: fix some python warnings)
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Build this swig module with Python 3.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert this tool to Python 3 and make it use that, to meet the 2020
deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert this tool to Python 3 and make it use that, to meet the 2020
deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert this tool to Python 3 and make it use that, to meet the 2020
deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update this test to use Python 3 to meet the 2020 deadline.
Also make it executable while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update this test to use Python 3 to meet the 2020 deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Convert buildman to Python 3 and make it use that, to meet the 2020
deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update this tool to use Python 3 to meet the 2020 deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present patman test fail in some environments which don't use utf-8
as the default file encoding. Add this explicitly.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present all the 'command' methods return bytes. Most of the time we
actually want strings, so change this. We still need to keep the internal
representation as bytes since otherwise unicode strings might break over
a read() boundary (e.g. 4KB), causing errors. But we can convert the end
result to strings.
Add a 'binary' parameter to cover the few cases where bytes are needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Bring over the fdt from this commit:
430419c (origin/master) tests: fix some python warnings
adding in the 'assumptions' series designed to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This board appears to be very near its size limit and cannot accept the
new checking code in libfdt. Disable this code so this the board can
continue to build.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
For better or worse libfdt recent grew a lot of code that checks the
validity of the device tree in great detail. When using unsigned or
unverified data this makes things safer, but it does add to code size.
Add some controls to select the trade-off between safety and code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Unfortunately libfdt needs this value now, which is present in the
stdint.h header. That file is just a placeholder in U-Boot and these sorts
of constants appear in the linux/kernel.h header instead.
To keep libfdt happy, add INT32_MAX too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191104
-------------------
- i.MX NAND: nandbcb support for MX6UL / i.MX7
- i.MX8: support for HAB
- Convert to DM (opos6ul, mccmon6)
- Toradex i.MX6ull colibri
- sync DTS with kernel
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/606853416
|
|
- Various CPSW related improvements, DTS resync
|
|
Conver TI CPSW driver to use dev/ofnode api.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
|
