summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-04-09arm: at91: siemens: Add support to generate combined SPL+U-Boot imageStefan Roese
This patch adds the necessary defines to the Siemens AT91SAM based boards (smartweb, corvus and taurus) to generate the combined binary image with SPL and main U-Boot image combined (u-boot-with-spl.bin). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09Makefile: Add Kconfig option CONFIG_SPL_IMAGE to select the SPL binaryStefan Roese
This patch adds the CONFIG_SPL_IMAGE option to select the SPL image that shall be used to generate the combined SPL + U-Boot image. The default value is the current value "spl/u-boot-spl.bin". This patch also sets CONFIG_SPL_IMAGE to "spl/boot.bin" for AT91 targets which use SPL NAND support (boot from NAND). For these build targets the combined image "u-boot-with-spl.bin" is now automatically generated and can be programmed into NAND as one single image (vs. SPL image and U-Boot as 2 separate images). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09Makefile.spl: Move generated AT91SAM NAND image boot.bin to spl directoryStefan Roese
This patch moves the AT91SAM NAND booting SPL image "boot.bin" which includes the ECC values from the root directory into the spl directory, where all SPL related images are located. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09arm: at91: arm926ejs/u-boot-spl.lds: Add _image_binary_end to SPL ldsStefan Roese
This patch adds _image_binary_end to the SPL linker script. This will be used be the upcoming GARDENA AT91SAM based platform, which uses DT in SPL and configures CONFIGURE_SPL_SEPARATE_BSS. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09arm: at91: Enable watchdog supportStefan Roese
This patch enables and starts the watchdog on the AT91 platform if configured. The WD timeout value is read in the AT91 WD device driver from the DT, using the "timeout-sec" DT property. If not provided in the DT, the default value of 2 seconds is used. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09arm: at91: Remove CONFIG_AT91_HW_WDT_TIMEOUTStefan Roese
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any more. The WD timeout value can be provided via the "timeout-sec" DT property. If not provided this way, the default value of 2 seconds will be used. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09watchdog: at91sam9_wdt: Fix WDT setup in at91_wdt_start()Stefan Roese
This patch fixes the timer register setup in at91_wdt_start() to correctly configure the register again. The input timeout value is now in milli-seconds instead of seconds with the new watchdog API. Make sure to take this into account and only use a max timeout value of 16 seconds as appropriate for this SoC. Also the check against a lower timeout value than 0 is removed. This check makes no sense, as the timeout value is unsigned. Signed-off-by: Stefan Roese <sr@denx.de> Reported-by: Heiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09watchdog: Handle SPL build with watchdog disabledStefan Roese
This patch adds some checks, so that the watchdog can be enabled in main U-Boot proper but can be disabled in SPL. This will be used by some AT91SAM based boards, which might enable the watchdog in the main U-Boot proper and not in SPL. It will be enabled in SPL by default there, so no need to configure it there. This approach saves some space in SPL. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09serial: atmel_usart: Use fixed clock value in SPL version with DM_SERIALStefan Roese
This patch adds an alterative SPL version of atmel_serial_enable_clk(). This enables the usage of this driver without full clock support (in drivers and DT nodes). This saves some space in the SPL image. Please note that this fixed clock support is only added to the SPL code in the DM_SERIAL part of this file. All boards not using SPL & DM_SERIAL should not be affected. This patch also introduces CONFIG_SPL_UART_CLOCK for the fixed UART input clock. It defaults to 132096000 for ARCH_AT91 but can be set to a different value if needed. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-09arm: at91: spl_at91.c: Call spl_early_init() if OF_CONTROL is enabledStefan Roese
This patch adds a call to spl_early_init() to board_init_f() which is needed when CONFIG_SPL_OF_CONTROL is configured. This is necessary for the early SPL setup including the DTB setup for later usage. Please note that this call might also be needed for non SPL_OF_CONTROL board, like the smartweb target. But smartweb fails to build with this call because its binary grows too big. So I disabled it for these kind of targets for now. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09arm: at91: Makefile: Compile lowlevel_init only when really necessaryStefan Roese
Make sure that lowlevel_init is not compiled when CONFIG_SKIP_LOWLEVEL_INIT_ONLY is configured. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
2019-04-09board: pm9g45: Migrate to CONFIG_DMIlko Iliev
Migrate the following options to CONFIG_DM: CONFIG_DM_GPIO CONFIG_DM_MMC CONFIG_DM_ETH CONFIG_DM_SERIAL CONFIG_DM_USB Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2019-04-09ARM: at91: sama5d2: Wrap cpu detection to fix macb driverAlexander Dahl
When introducing the SAMA5D27 SoCs, the SAMA5D2 series got an additional chip id. The check if the cpu is sama5d2 was changed from a preprocessor definition (inlining a call to 'get_chip_id()') to a C function, probably to not call get_chip_id twice? That however broke a check in the macb ethernet driver. That driver is more generic and also used for other platforms. I suppose this solution was implemented to use it in 'gem_is_gigabit_capable()', without having to stricly depend on the at91 platform: #ifndef cpu_is_sama5d2 #define cpu_is_sama5d2() 0 #endif That only works as long as cpu_is_sama5d2 is a preprocessor definition. (The same is still true for sama5d4 by the way.) So this is a straight forward fix for the workaround. The not working check on the SAMA5D2 CPU lead to an issue on a custom board with a LAN8720A ethernet phy connected to the SoC: => dhcp ethernet@f8008000: PHY present at 1 ethernet@f8008000: Starting autonegotiation... ethernet@f8008000: Autonegotiation complete ethernet@f8008000: link up, 1000Mbps full-duplex (lpa: 0xffff) BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 BOOTP broadcast 8 BOOTP broadcast 9 BOOTP broadcast 10 BOOTP broadcast 11 BOOTP broadcast 12 BOOTP broadcast 13 BOOTP broadcast 14 BOOTP broadcast 15 BOOTP broadcast 16 BOOTP broadcast 17 Retry time exceeded; starting again Notice the wrong reported link speed, although both SoC and phy only support 100 MBit/s! The real issue on reliably detecting the features of that cadence ethernet mac IP block, is probably more complicated, though. Fixes: 245cbc583d ("ARM: at91: Get the Chip ID of SAMA5D2 SiP") Signed-off-by: Alexander Dahl <ada@thorsis.com>
2019-04-08Prepare v2019.04Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-08arm: sunxi: Enable DM_MMC on required SoCsJagan Teki
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular target making invalid reading to the disk drive. Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40 would eventually end-up with scsi disk read failures like [1] So, enable DM_MMC in all places of respective SoC's instead of enabling them globally to Allwinner platform. Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40. [1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-08Merge tag 'fixes-for-2019.04-rc4' of git://git.denx.de/u-boot-stagingTom Rini
- i.MX8QXP-MEK ethernet fix
2019-04-08dts: imx8qxp-mek: Add PHY post reset delayAndrejs Cainikovs
PHY cannot be detected unless we wait about 150 ms. Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-08net: dm: fec: Support phy-reset-post-delay propertyAndrejs Cainikovs
As per Linux kernel DT binding doc: - phy-reset-post-delay : Post reset delay in milliseconds. If present then a delay of phy-reset-post-delay milliseconds will be observed after the phy-reset-gpios has been toggled. Can be omitted thus no delay is observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2019-04-08watchdog: Move watchdog_dev to data section (BSS may not be cleared)Stefan Roese
This patch moves all instances of static "watchdog_dev" declarations to the "data" section. This may be needed, as the BSS may not be cleared in the early U-Boot phase, where watchdog_reset() is already beeing called. This may result in incorrect pointer access, as the check to "!watchdog_dev" in watchdog_reset() may not be true and the function may continue to run. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Marek Behún" <marek.behun@nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100) Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2019-04-07net: phy: implement fallback mechanism for negative phy adressesHannes Schmelzer
Negative phy-addresses can occour if the caller function was not able to determine a valid phy address (from device-tree for example). In this case we catch this here and search for ANY phy device on the given mdio- bus. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Lukasz Majewski <lukma@denx.de>
2019-04-05Merge tag 'u-boot-imx-20190405' of git://git.denx.de/u-boot-imxTom Rini
Fixes for 2019.04 - fix bashism for MX8 - fix ethernet for MX53 - fix docs for i.MX8
2019-04-03Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- Documentation fix
2019-04-03Merge branch '2019-04-03-master-imports'Tom Rini
- Important Khadas VIM2 fix - Build fix for macOS Mojave - Build fix for gcc-4.7 for host tools.
2019-04-03tools/Makefile: build host tools with -std=gnu99Thomas Petazzoni
Parts of the code are using C99 constructs (such as variables declared inside loops), but also GNU extensions (such as typeof), so using -std=gnu99 is necessary to build with older versions of gcc that don't default to building with gnu99. It fixes the following build failure: ./tools/../lib/crc16.c: In function "crc16_ccitt": ./tools/../lib/crc16.c:70:2: error: "for" loop initial declarations are only allowed in C99 mode for (int i = 0; i < len; i++) ^ ./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code when building the host tools with gcc 4.7. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-04-03fix compile error on macOS Mojave默默
2019-04-03configs: khadas_vim2: Fix defconfigNeil Armstrong
The Khadas VIM2 defconfig was missing the USB PHY config and two other misc configs to setup dram banks and call misc_init_r. Align it on the other Amlogic SoC based boards defconfig. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-03phy: Also allow MESON_GXM for MESON_GXL_USB_PHYNeil Armstrong
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs. Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-02travis-ci: fix at91 missing boardsEugen Hristev
Fix missing at91 boards and split the at91 in two categories: at91 arm v7 at91 arm926esj which are the two main cores for the at91 architecture. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-02DTS: Fix ETH PHY reset on HSC|DDC boards (imx53)Lukasz Majewski
After the commit: "eth: dm: fec: Add gpio phy reset binding" SHA1: efd0b791069af93e9d439a70d1fe2ae8994dbbfa The FEC ETH driver switched to PHY GPIO reset performed with data defined in DTS. For the HSC|DDC boards the GPIO reset signal is active low and hence the wrong DTS description must be changed (otherwise the reset for ETH is not properly setup). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-02cosmetic: Remove not needed string from kp_imx53.h configLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-02cosmetic: config: Remove empty #ifdefsLukasz Majewski
After running tools/moveconfig.py it turned out that for various boards there are an empty #ifdef statements. Remove them to clean u-boot source code. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-02doc: Fix outdated ohci board hook documentationKrzysztof Kozlowski
The ohci driver calls board_usb_init(), not usb_board_init(). Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2019-04-02imx8mq_evk: README: Make the underline marker fill the whole sentenceFabio Estevam
Let the underline marker "=" fill the whole sentence for better readability. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-02imx8mq_evk: README: Fix a typo in the destination pathFabio Estevam
The DDR firmware binaries should be copied to '$(srctree)', so fix a typo. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-02imx8mq_evk: README: Need to copy bl31.bin to U-Boot source treeFabio Estevam
After building ATF it is needed to copy the generated bl31.bin file to the U-Boot source tree. Make this step explicit in the instructions. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-01Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
Minor fixes for the Alt board and PHY use on Gen2.
2019-04-01Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- clk: sunxi: a10: Add CLK_AHB_GMAC
2019-04-01clk: sunxi: a10: Add CLK_AHB_GMACJagan Teki
CLK_AHB_GMAC was suppose to be part of previous commit "clk: sunxi: Implement A10 EMAC clocks" add it so-that we can get rid of sunxi_set_gate warning on boot message. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-01tools/imx8m_image.sh: remove bashismBaruch Siach
Use a single '=' to test string equality for compatibility with non-bash shells. Otherwise, if /bin/sh is dash, build fails: ./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator ./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator ./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator ./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator WARNING './spl/u-boot-spl-ddr.bin' not found, resulting binary is not-functional Signed-off-by: Baruch Siach <baruch@tkos.co.il> Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
2019-04-01Merge tag 'u-boot-imx-20190401' of git://git.denx.de/u-boot-imxTom Rini
Fixes for 2019.01 - pico-imx6ul: fix after conversion - engicam boards - pico-imx7d _ README due to hang with imx-usb-loader
2019-03-31pico-imx7d: README: Recommend the usage of a USB hubFabio Estevam
Since commit 9e3c0174da842 ("pico-imx7d: Add LCD support") we started to notice some hangs in U-Boot. There is not an issue on such commit per se, but due to the LCD support the current drawn is increased and this may cause issues when powering pico-imx7d-pi from USB. Some computers may be a bit strict with USB current draw and will shut down their ports if the draw is too high. The solution for that is to use an externally powered USB hub between the board and the host computer. Add such recommendation to the README file. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-03-31configs: icorem6: Use imx6 cratch register for bootcountJagan Teki
SRAM address used for bootcount on exiting code is erasing previous count value when system reset from Linux. So use the dedicated imx6 scratch register, GPR2 to preserve the contents even if the system reset from Linux. Fixes: 4eb9aa39350e ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter") Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2019-03-31configs: icore: Fix U-Boot proper loading from nandMichael Trimarchi
SPL on Engicam i.Core M6 boards enabled DM, so it would require some malloc() pool before relocation in order to load U-Boot proper properly. So, enable SPL malloc() pool of 0x2000 size similarly like what we have used for icore mmc defconfigs. Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-03-31ARM: imx6q_logic: Enable UUID supportAdam Ford
With UUID support, the root can now point to UUID. This makes swiching between mmc 0 and mmc 1 easier by simplying changing mmcdev between 0 and 1. From there, the scripts handle the rest. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-03-31pico-imx6ul: Fix eMMC boot after DM_MMC conversionFabio Estevam
After the DM_MMC conversion the following eMMC boot error is observed: U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000) Trying to boot from MMC1 MMC Device 0 not found spl: could not find mmc device 0. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### This happens because the SPL code does not initialize the SDHC pins and clock. Fix it by moving the original eMMC initialization from U-Boot proper to SPL. Reported-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-03-31Merge branch 'master' of git://git.denx.de/u-bootStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-03-31Merge tag 'video-fixes-for-2019.04-rc4' of git://git.denx.de/u-boot-videoTom Rini
sunxi HDMI clock fix
2019-03-31Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchipTom Rini
Last-minute fixes for Rockchip for 2019.04: - reverts the deprecation of the 'download-key' detection (with a full solution pending for the next release) - applies a temporary fix for the 32bit pinctrl registers on the RK3288
2019-03-31dfu: usb: Update MAINTAINERS file regarding DFU/USB gadget supportLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-03-30ARM: rmobile: alt: Fix I2C bus numberMarek Vasut
The I2C bus number to access the PMIC is I2C 7, fix this. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
generated by cgit (git 2.34.1) at 2025-01-19 08:28:08 +0000