summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/arm1136/start.S
AgeCommit message (Collapse)Author
2011-03-27arm: fix incorrect monitor protection region in FLASHPo-Yu Chuang
Monitor protection region in FLASH did not cover .rel.dyn and .dynsym sections, because it uses __bss_start to compute monitor_flash_len. Use _end instead. Add _end to linker scripts for end of u-boot image Add _end_ofs to all the start.S. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-03-27rename _end to __bss_end__Po-Yu Chuang
Currently, _end is used for end of BSS section. We want _end to mean end of u-boot image, so we rename _end to __bss_end__ first. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-02-21arm1136 relocation: Fix calculation of board_init_rFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-02-21arm1136: Fix NAND bootFabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2011-02-02ARM: */start.S: code cleanupLiu Hui-R64343
Remove the useless code from start.S Signed-off-by: Jason Liu <r64343@freescale.com> Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-13ARM: */start.S: use canonical asm syntaxWolfgang Denk
Make code build with older tool chains. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-09arm: fixloop(): do not use r8 for relocationAndreas Bießmann
r8 is used for global_data and should therefore be left alone! For C code the compiler flag --fixed-r8 does the job, but in assembler we need to be aware of that fact. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-09arm: relocate_code(): do not set register uselessAndreas Bießmann
In case we are still at relocation target address before relocation we do not need to load the registers needed for relocation. We should instead skip the whole relocation part and jump over to clear_bss immediately. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-09arm: copy_loop(): use scratch registerAndreas Bießmann
This patch uses r1 as scratch register for copy_loop(). Therefore we do not longer need r7 for the storage of relocate_code()'s 'addr_moni' (the destination address of relocation). Therefore r7 can be used later on for other purposes. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-08arm: add 8-byte alignment for ABI compliance before board_init_fHeiko Schocher
suggested from Daniel Hobi<daniel.hobi@schmid-telecom.ch> Tested on following boards: arm1136: qong armv7: omap3_beagle arm926ejs: magnesium, tx25 Signed-off-by: Heiko Schocher <hs@denx.de> cc: Daniel Hobi <daniel.hobi@schmid-telecom.ch> cc: Albert ARIBAUD <albert.aribaud@free.fr>
2010-11-17ARM: fix linker file for newer ld supportAlbert Aribaud
older ld emitted all ELF relocations in input sections named .rel.dyn, whereas newer ld uses names of the form .rel*. The linker script only collected .rel.dyn input sections. Rewrite to collect all .rel* input sections. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-10-29Drop support for CONFIG_SKIP_RELOCATE_UBOOTWolfgang Denk
For ARM systems, before ELF relocation was introduced, CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the U-Boot image from whereever it was loaded to it's link address (CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation was performed at all, it was just a memcpy(). With ELF relocation, this does not work like that any more, and related boards need to be fixed anyway. So don't keep this relict any longer. Signed-off-by: Wolfgang Denk <wd@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29Drop support for CONFIG_SYS_ARM_WITHOUT_RELOCWolfgang Denk
When this define was introduced, the idea was to provide a soft migration path for ARM boards to get adapted to the new relocation support. However, other recent changes led to a different implementation (ELF relocation), where this no longer works. By now CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it actually hurts because it obfuscates the actual code by sprinkling it with lots of dead and non-working debris. So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC. Signed-off-by: Wolfgang Denk <wd@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-26ARM: use the same branch insn on all architecturesWolfgang Denk
For the "fixloop" implementation in start.S a number of different instructions was used. Unify code so all architectures use "blo" here because it is more robust in case of incorrect alignments. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.aribaud@free.fr> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Acked-by: Heiko Schocher <hs@denx.de>
2010-10-26ARM: fix address setup in start.SDarius Augulis
Fix address setup bug for ARM. This bug stops u-boot booting if CONFIG_SKIP_RELOCATE_UBOOT is defined. Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
2010-10-26Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated valueWolfgang Denk
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26ARM: Use consistent assembler syntaxGray Remlin
Signed-off-by: Gray Remlin <g_remlin@rocketmail.com> Acked-by: Heiko Schocher <hs@denx.de>
2010-10-19Merge branch 'elf_reloc'Wolfgang Denk
Conflicts: arch/arm/include/asm/config.h board/LaCie/edminiv2/config.mk board/karo/tx25/config.mk board/logicpd/imx27lite/config.mk doc/README.arm-relocation Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk
The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-13arm1136, qong: add support for ELF relocationsHeiko Schocher
Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Heiko Schocher <hs@denx.de> cc: Albert ARIBAUD <albert.aribaud@free.fr>
2010-10-11arm: bugfix: replace ble with blo in start.S filesAlbert Aribaud
Generalized misuse of ble within relocation and bss initialization loops caused one iteration too many. Instead of ble ('branch if lower or equal'), use blo ('branch if lower'). While we're at it, fix all 'addreee' typos. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-09-19ARM: implement relocation for ARM11Heiko Schocher
Change the implementation for ARM11 to relocate the code to an arbitrary address in RAM. Tested on the qong board. Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de>
2010-09-19ARM (ARM11): add data cache support, test on Qong boardHeiko Schocher
Add data cache support for arm1136 systems. Enable "cache" command on Qong board and test performance. Test 1: Loading 127 MB of data from NAND flash into RAM: Instr. Cache off on on Data Cache off off on -------------------------------------------------- QONG (ARM11) 177s 95s 43s = x 4.1 Test 2: uncompressing a gzipped image from RAM to RAM (size compressed: 6.5 MiB, uncompressed: 35 MiB): Instr. Cache off on on Data Cache off off on -------------------------------------------------- QONG (ARM11) 1.54s 0.95s 0.18s = x 8.6 Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de>
2010-06-22ARM: Align stack to 8 bytesVitaly Kuzmichev
The ARM ABI requires that the stack be aligned to 8 bytes as it is noted in Procedure Call Standard for the ARM Architecture: http://infocenter.arm.com/help/topic/com.arm.doc.ihi0042d/index.html Unaligned SP also causes the problem with variable-length arrays allocation when VLA address becomes less than stack pointer during aligning of this address, so the next 'push' in the stack overwrites first 4 bytes of VLA. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-06-01ARM1136: Fix cache_flush() error and correct cpu_init_crit() commentsGeorge G. Davis
The ARM1136 cache_flush() function uses the "mcr p15, 0, rn, c7, c7, 0" instruction which means "Invalidate Both Caches" when in fact the intent is to clean and invalidate all caches. So add an "mcr p15, 0, %0, c7, c10, 0" instruction to "Clean Entire Data Cache" prior to the "Invalidate Both Caches" instruction to insure that memory is consistent with any dirty cache lines. Also fix a couple of "flush v*" comments in ARM1136 cpu_init_crit() so that they correctly describe the actual ARM1136 CP15 C7 Cache Operations used. Signed-off-by: George G. Davis <gdavis@mvista.com>
2010-04-13arm: Move cpu/$CPU to arch/arm/cpu/$CPUPeter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
generated by cgit (git 2.34.1) at 2024-12-29 19:58:02 +0000