summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7/am33xx
AgeCommit message (Collapse)Author
2012-09-01am33xx: Rework config_io_ctrl slightlyTom Rini
This function sets a number of related registers to the same value (the registers in question all have the same field descriptions and are related in operation). Rather than defining a struct and setting the value repeatedly, just pass in the value. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Use emif_regs struct for storing initialization valuesTom Rini
Rather than defining our own structs to note what to use when programming the EMIF and related re-use the emif_regs struct. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Turn a number of 'int' functions to 'void'Tom Rini
A number of memory initalization functions were int and always returned 0. Further it's not feasible to be doing error checking here, so simply turn them into void functions. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Document what we're doing with ddrctrl->ddrckectrlTom Rini
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros. - Comment what we're really setting in ddrctrl->ddrckectrl which is that we're operating in the normal mode where EMIF/PHY clock is controlled by the PHY. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Clean up unused DDR defines, prefix more with 'DDR2'Tom Rini
- Remove a handful of unused defines. - Prefix more values with 'DDR2' as DDR3 will require different values. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Move the call to ddr_pll_config, make it take the frequencyTom Rini
Depending on if we have DDR2 or DDR3 on the board we will need to call ddr_pll_config with a different value. This call can be delayed slightly to the point where we know which type of memory we have. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Pass to config_ddr the type of memory that is connectedTom Rini
We need to pass in the type of memory that is connected to the board. The only reliable way to do this is to know what type of board we are running on (which later will be knowable in s_init()). For now, pass in the value of DDR2. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Make config_cmd_ctrl / config_ddr_data take const structsTom Rini
Rework the EMIF4/DDR code slightly to setup the structs that config_cmd_ctrl and config_ddr_data take to be setup at compile time and mark them as const. This lets us simplify the calling path slightly as well as making it easier to deal with DDR3. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Rework DDR2 EMIF initalization slightlyTom Rini
With the previous bugfix we now don't need to set two different REF_CTRL values and instead set the final value. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Bugfix to config_sdram()Tom Rini
When we change SDRAM_CONFIG this triggers a refresh based on all of the parameters that we have programmed so we must do this last. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Remove extra check in enable_ddr_clocksTom Rini
We do not need to check for EMIF_GCLK and L3_GCLK being active. This was a hold-over from bringup and no longer required. Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Convert to using <asm/emif.h> to describe the EMIFTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: Enable gpio0 clockTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01am33xx: CPSW init and definitionsChandan Nath
This patch adds platform-specific initialization for CPSW switch on TI AM33XX SoCs. Signed-off-by: Chandan Nath <chandan.nath@ti.com> [Ilya: split init out of original patch] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01omap: am335x_evm: enable i2c1 channelSteve Sakoman
This patch sets up pinmux, enables fclk, and defines CONFIG_I2C_MULTI_BUS Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01omap: am33xx: enable gpio supportSteve Sakoman
This patch uses the code in omap-common to support gpio modules 1-3 on am33xx based boards. It adds base address and register definitions, enables clocks to the modules, and enables building the common gpio code for CONFIG_AM33XX as well as CONFIG_OMAP Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-07-07am33xx: Do not call init_timer twiceTom Rini
We do not need to call init_timer both in SPL and U-Boot itself, just SPL needs to initialize the timer. Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit
Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
2012-01-23ARM: AM33XX: Add i2c supportPatil, Rachna
Add i2c driver board hookup for AM335X EVM Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
2012-01-16ARM:AM33XX: Add SPL support for AM335X EVMChandan Nath
This patch is added to support SPL feature on AM335X platform. In this patch, MMC1 is configured as boot device for SPL and support for other devices will be added in the next patch series. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16ARM:AM33XX: Add mmc/sd supportChandan Nath
This patch add supports for mmc/sd driver on AM335X platform. PLL and pinmux configurations for mmc/sd are configured in this patch. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16ARM:AM33XX: Fix ddr and timer register offsetChandan Nath
This patch is added to update incorrect ddr and timer register offset. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2011-10-27ARM:AM33XX: Add support for TI AM335X EVMChandan Nath
This patch adds basic support for booting the board. This patch adds support for the UART necessary to get to the u-boot prompt. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27ARM:AM33XX: Add emif/ddr supportChandan Nath
This patch adds AM33xx emif/ddr support along with board specific defines. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27ARM:AM33XX: Add clock definitionsChandan Nath
This patch adds basic clock definition of am33xx SoC. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27ARM:AM33XX: Added support for AM33xxChandan Nath
This patch adds basic support for AM33xx which is based on ARMV7 Cortex A8 CPU. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit (git 2.34.1) at 2025-01-01 18:45:14 +0000