| Age | Commit message (Collapse) | Author |
|---|
|
Commit 6c739c5d added code to enable i2c bus 4 and 5 on the sun7i SoC
but forgot to extend the range check in clock_twi_onoff, resulting in
the clock not getting enabled.
The range-check is not needed at all, since clock_twi_onoff only gets
called with such high indexes when CONFIG_I2C3_ENABLE / CONFIG_I2C4_ENABLE
is set and Kconfig already only allows these on sun6i / sun7i.
This commit removes the range-check all together fixing i2c bus 4 and 5
not working on sun7i.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
[hdegoede@redhat.com] Remove range check instead of extending it
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.
PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.
The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add a helper function to get the pll3 clock rate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add support for the new second DRAM PLL found on the A33 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
As the comment says now that we have SPL support this is no longer necessary,
as PLL6 is already setup with the exact same parameters by the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Our old hardcoded k and m values are based on PLL5 being configured in steps
of 48 MHz, which is correct for sun6i where the DRAM PLL runs at twice the
DRAM CLK, which is usually configured in 24 MHz step. But on the A23 (sun8i)
the PLL5 runs at half the DRAM CLK, so we require 12 MHz steps.
This commit adjusts clock_set_pll5 to automatically select the best k and m
depending on the requested clk rate.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The sun8i dram code sometimes wants to enable sigma delta mode,
add a parameter to allow this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This is a preparation patch for adding support for HDMI out.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).
Also add some extra clock register constant defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The A23 only has UART0 muxed with MMC0. Some of the boards we
encountered expose R_UART as a set of pads.
Add support for R_UART so we can have a console while using mmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This patch adds the basic clocks support for the Allwinner A31 (sun6i)
processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.
This includes changes from the following commits from u-boot-sunxi:
a92051b ARM: sunxi: Add sun6i clock controller structure
1f72c6f ARM: sun6i: Setup the UART0 clocks
5f2e712 ARM: sunxi: Enable pll6 by default on all models
2be2f2a ARM: sunxi-mmc: Add mmc support for sun6i / A31
12e1633 ARM: sun6i: Add initial clock setup for SPL
1a9c9c6 ARM: sunxi: Split clock code into common, sun4i and sun6i code
0b194ee ARM: sun6i: Properly setup the PLL LDO in clock_init_safe
b54c626 sunxi: avoid sr32 for APB1 clock setup.
68fe29c sunxi: remove magic numbers from clock_get_pll{5,6}
c89867d sunxi: clocks: clock_get_pll5 prototype and coding style
501ab1e ARM: sunxi: Fix sun6i PLL6 settings
37f669b ARM: sunxi: Fix macro names for mmc and uart reset offsets
61de1e6 ARM: sunxi: Correct comment for MBUS1 register in sun6i clock definitions
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: styling fixes reported by checkpatch.pl]
[wens@csie.org: drop unsupported SPL code block and unused gpio.h header]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
