summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
AgeCommit message (Collapse)Author
2011-12-06PXA: Replace timer driverMarek Vasut
This new timer driver shall conform to new Timer API. Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06PXA: Add cpuinfo display for PXA2xxMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06PXA: Separate PXA2xx CPU initMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]XMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06PXA: Re-add the Dcache locking as RAM for pxa250Marek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefan Herbrechtsmeier <sherbrec@cit-ec.uni-bielefeld.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-12-06PXA: Rework start.S to be closer to other ARMsMarek Vasut
The start.S on PXA was very obscure. This reworks it back to be close to arm1136 start.S and others. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> V2: Don't compile in relocation support if building SPL
2011-11-29OMAP3: Use sdelay from arch/arm/cpu/armv7/syslib.c instead of cloning that.Alexander Holler
There is no need to have such a function twice. Signed-off-by: Alexander Holler <holler@ahsoftware.de> Acked-by: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-29Fix Stelian's email addressStelian Pop
Change my old email address which is no longer valid. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-23Merge branch 'hs@denx.de' of git://git.denx.de/u-boot-stagingWolfgang Denk
* 'hs@denx.de' of git://git.denx.de/u-boot-staging: drivers/net/dnet.c: Fix GCC 4.6 warnings board/xaeniax/flash.c: Fix GCC 4.6 warnings net/bootp.c: Fix GCC 4.6 warning common/cmd_bootm.c: Fix GCC 4.6 warnings board/mx1ads/mx1ads.c: Fix GCC 4.6 warning board/mx1ads/syncflash.c: Fix GCC 4.6 warnings board/lubbock/flash.c: Fix GCC 4.6 warnings drivers/net/cs8900.c: Fix GCC 4.6 warning arch/arm/cpu/arm926ejs/omap/cpuinfo.c: Fix GCC 4.6 warnings drivers/net/lan91c96.c: Fix GCC 4.6 warning board/ronetix/pm9263/pm9263.c: Fix GCC 4.6 warning drivers/mtd/onenand/samsung.c: Fix GCC 4.6 warning drivers/usb/musb/musb_hcd.c: Fix GCC 4.6 warning
2011-11-23arch/arm/cpu/arm926ejs/omap/cpuinfo.c: Fix GCC 4.6 warningsAnatolij Gustschin
Fix: cpuinfo.c: In function 'print_cpuinfo': cpuinfo.c:155:6: warning: variable 'system_serial_low' set but not used [-Wunused-but-set-variable] cpuinfo.c:154:6: warning: variable 'system_serial_high' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-16arch/arm/cpu/armv7/s5p-common/pwm.c: fix GCC 4.6 warningAnatolij Gustschin
Fix: pwm.c: In function 'pwm_config': pwm.c:85:16: warning: variable 'timer_rate_hz' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-15arm, davinci: da850/dm365 lowlevel cleanupHeiko Schocher
- Cleanup a lot of fix values, and use defines instead. - Also make some values configurable through the board config file. - delete the NAND_SPL code for da850, as it is not used actually - remove the asm code Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Tom Rini <tom.rini@gmail.com> Cc: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15omap4/5: Add support for booting with CH.Sricharan
Configuration header(CH) is 512 byte header attached to an OMAP boot image that will help ROM code to initialize clocks, SDRAM etc and copy U-Boot directly into SDRAM. CH can help us in by-passing SPL and directly boot U-boot, hence it's an alternative for SPL. However, we intend to support both CH and SPL for OMAP4/5. Initialization done through CH is limited and is not equivalent to that done by SPL. So U-Boot has to distinguish between the two cases and handle them accordingly. This patch takes care of doing this. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15omap5: emif: Add emif/ddr configurations required for omap5 evmSricharan
Add the emif configurations required for omap5 soc.Add the correct ddr part configurations required for omap5 evm board. EDB8164B3PH from ELPIDA is the part used on the board. Also changes are done to retain some part of the code common for OMAP4/5 and keep only the remaining in the Soc specific directories. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15omap5: clocks: Add clocks support for omap5 platform.Sricharan
Adding the correct configurations required for dplls, clocks, for omap5 Soc. Also changes are done to retain some part of the code common for OMAP4/5 and move only the remaining to the Soc specific directories. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15omap5: Add minimal support for omap5430.Sricharan
This patch adds the minimal support for OMAP5. The platform and machine specific headers and sources updated for OMAP5430. OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture. It's a dual core SOC with GIC used for interrupt handling and SCU for cache coherency. Also moved some part of code from the basic platform support that can be made common for OMAP4/5. Rest is kept out seperately. The same approach is followed for clocks and emif support in the subsequent patches. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15omap4: make omap4 code common for future reuseSricharan
Much of omap4 soc support code can be reused for omap5. Move them to the omap-common directory to facilitate this. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-11mx31: Fix checkpatch warnings in generic.cFabio Estevam
Fix checkpatch warnings in generic.c. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2011-11-11mx31: Use proper IO accessor for GPR registerFabio Estevam
Use proper IO accessor for GPR register. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2011-11-11mx31: Remove duplicate definition for GPR registerFabio Estevam
GPR register definition is already available at imx-regs.h, so remove the duplication. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2011-11-11iMX28: Fix ARM vector handlingMarek Vasut
This patch introduces proper ARM vector handling for i.MX28 CPU. This issue wasn't addressed because the interrupts weren't enabled on any ARMv5 core, therefore the issue wasn't noticed earlier. In previous implementation, the vectoring code used by i.MX28 CPU when an exception happened was that of the SPL. With this change, the branch target when an exception happens can be reconfigured by U-Boot. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-11-11iMX28: Add GPIO controlMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-11-11iMX28: Add PINMUX controlMarek Vasut
Taken from Linux kernel with minor modifications: commit bf985969e27b507f734435a99df8bf745a3dbb2b Author: Shawn Guo <shawn.guo@freescale.com> Date: Mon Dec 20 22:57:43 2010 +0800 ARM: mxs: Add iomux support Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-11-11iMX28: Initial support for iMX28 CPUMarek Vasut
This patch supports: - Timers - Debug UART - Clock Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-11-08SPL: Allow ARM926EJS to avoid compiling in the CPU support codeMarek Vasut
This allows the SPL to avoid compiling in the CPU support code. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Scott Wood <scottwood@freescale.com>
2011-11-08arm: a320: fix broken timerPo-Yu Chuang
timer.c used static data and are called before relocation. Move all static variables into global_data structure. Also cleanup timer.c from unused stubs and make it truly use 64 bit tick values. Remove reset_timer_masked() get_timer_masked() reference: arch/arm/cpu/arm926ejs/at91/timer.c Based on Reinhard Meyer <u-boot@emk-elektronik.de>'s patches 5dca710a3d7703e41da0e9894f2d71f9e25bea6b cfff263f41e32c7ba2ee9162a8cc6423eb5a8390 Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Tested-by: Macpaul Lin <macpaul@gmail.com>
2011-11-08arm, davinci: Fix setting of the SDRAM configuration registerChristian Riesch
da850_ddr_setup() expects the BOOTUNLOCK bit to be set in If BOOTUNLOCK is not set in this define, several configuration bits will not be writeable and the code will not work. Since the BOOTUNLOCK and TIMUNLOCK bits are not configuration options but access control bits, this patch changes the code to work irrespective of the value of these bits in CONFIG_SYS_DA850_DDR2_SDBCR. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-08arm, davinci: Remove the duplication of LPSC functionsChristian Riesch
The LPSC functions defined in arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c are replaced by those already defined in arch/arm/cpu/arm926ejs/davinci/psc.c. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-08arm, davinci: Rename AM1808 lowlevel functions to DA850Christian Riesch
Rename arch/arm/cpu/arm926ejs/davinci/am1808_lowlevel.c and arch/arm/include/asm/arch-davinci/am1808_lowlevel.h to da850_lowlevel.c and da850_lowlevel.h since they apply not only to the AM1808 SoC but to all DA850 chips. The function names and #defines are changed likewise. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-04mx53: Turn off child clocks before reconfigure perclk_rootFabio Estevam
In addition to ensuring that PERCLK remains at least 2.5 times slower than the AHB clock, certain steps need to be followed to ensure robust operation of PERCLK when reconfiguring the PERCLK clock source. To properly configure the PERCLK clock source, the following steps are required: 1.In the CCGR registers, gate the clocks to all PERCLK-dependent modules. 2.Select the desired input clock for the PERCLK root clock (to be either source from the peripherals main source clock or the lp_apm clock source). Refer to the CMCBR register, perclk_lp_apm_sel bit. 3.Configure the perclk_pred1, perclk_pred2, and perclk_podf dividers to the desired setting. Refer to the CBCDR register for details. 4.In the CCGR registers, enable the desired clocks for the PERCLK-dependent module clocks. If these steps aren't followed, GPT timer may stop and the kernel stops at "Calibrating delay loop". Signed-off-by: Terry Lv <r65388@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-11-03arm926ejs, davinci: add cpuinfo for dm365Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03arm, davinci: add lowlevel function for dm365 socHeiko Schocher
used for booting (for example) from NAND using spl code. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03arm, davinci: add support for new spl frameworkHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03omap/spl: actually enable the consoleIlya Yanok
Currently OMAP SPL code does all the initialization but does not set the gd->have_console value so no output is actually performed. This patch sets gd->have_console to 1. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03arm, arm926: fix missing symbols in NAND_SPL modeHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03arm, davinci: Add function lpsc_syncreset()Christian Riesch
This patch adds a function lpsc_syncreset that allows setting a lpsc module into Sync Reset state. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03kirkwood: drop empty asm-offsets.s fileMike Frysinger
This generated file does not belong in the tree -> punt. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2011-11-03mx31: define pins and init for UART2 and CSPI3Helmut Raiger
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
2011-11-03mx31: Introduce mx31_set_gpr functionFabio Estevam
Introduce mx31_set_gpr function for setting the GPR (General Purpose Register) on MX31. This function can be useful for setting a group of pins into tied to some specific peripherals. Reuse this function from the linux kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-11-03MX35: add reset cause as provided by other i.MXStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-11-03Reduce build timesWolfgang Denk
U-Boot Makefiles contain a number of tests for compiler features etc. which so far are executed again and again. On some architectures (especially ARM) this results in a large number of calls to gcc. This patch makes sure to run such tests only once, thus largely reducing the number of "execve" system calls. Example: number of "execve" system calls for building the "P2020DS" (Power Architecture) and "qong" (ARM) boards, measured as: -> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board> -> grep execve /tmp/foo | wc -l Before: After: Reduction: ================================== P2020DS 20555 15205 -26% qong 31692 14490 -54% As a result, built times are significantly reduced, typically by 30...50%. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Albert Aribaud <albert.aribaud@free.fr> cc: Graeme Russ <graeme.russ@gmail.com> cc: Mike Frysinger <vapier@gentoo.org> Tested-by: Graeme Russ <graeme.russ@gmail.com> Tested-by: Matthias Weisser <weisserm@arcor.de> Tested-by: Sanjeev Premi <premi@ti.com> Tested-by: Simon Glass <sjg@chromium.org> Tested-by: Macpaul Lin <macpaul@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-28Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
* 'master' of git://git.denx.de/u-boot-arm: ARM: Add Calxeda Highbank platform dkb: make mmc command as default enabled Marvell: dkb: add mmc support ARM: pantheon: add mmc definition davinci: remove config.mk file from the sources ARM:AM33XX: Add support for TI AM335X EVM ARM:AM33XX: Added timer support ARM:AM33XX: Add emif/ddr support ARM:AM33XX: Add clock definitions ARM:AM33XX: Added support for AM33xx omap3/emif4: fix registers definition davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM davinci: emac: add support for more than 1 PHYs davinci: emac: add new features to autonegotiate for EMAC da850evm: Move LPSC configuration to board_early_init_f() omap4_panda: Build in cmd_gpio support on panda omap: Don't use gpio_free to change direction to input mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset OMAP3: overo : Add environment variable optargs to bootargs OMAP3: overo: Move ethernet CS4 configuration to execute based on board id OMAP3: overo : Use ttyO2 instead of ttyS2. da830: add support for NAND boot mode dm36x: revert cache disable patch dm644X: revert cache disable patch devkit8000: Add malloc space omap: spl: fix build break due to changes in FAT OMAP3 SPL: Provide weak omap_rev_string omap: beagle: Use ubifs instead of jffs2 for nand boot omap: overo: Disable pull-ups on camera PCLK, HS and VS signals omap: overo: Configure mux for gpio10 SPL: Add DMA library omap3: Add interface for omap3 DMA omap3: Add DMA register accessors omap3: Add Base register for DMA arm, davinci: add missing LSPC define for MMC/SD1 U-Boot/SPL: omap4: Make ddr pre-calculated timings as default. DaVinci: correct MDSTAT.STATE mask omap4: splitting padconfs into common, 4430 and 4460 omap4: adding revision detection for 4460 ES1.1 omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL gplug: fixed build error as a result of code cleanup patch kirkwood_spi: add dummy spi_init() gpio: mvmfp: reduce include platform file ARM: orion5x: reduce dependence of including platform file serial: reduce include platform file for marvell chip ARM: kirkwood: reduce dependence of including platform file ARM: armada100: reduce dependence of including platform file ARM: pantheon: reduce dependence of including platform file Armada100: Add env storage support for Marvell gplugD Armada100: Add SPI flash support for Marvell gplugD Armada100: Add SPI support for Marvell gplugD SPI: Add SPI driver support for Marvell Armada100 dreamplug: initial board support. imx: fix coding style misc: pmic: drop old Freescale's pmic driver MX31: mx31pdk: use new pmic driver MX31: mx31ads: use new pmic driver MX31: mx31_litekit: use new pmic driver MX5: mx53evk: use new pmic driver MX5: mx51evk: use new pmic driver MX35: mx35pdk: use new pmic driver misc: pmic: addI2C support to pmic_fsl driver misc: pmic: use I2C_SET_BUS in pmic I2C MX5: efikamx/efikasb: use new pmic driver MX3: qong: use new pmic driver RTC: Switch mc13783 to generic pmic code MX5: vision2: use new pmic driver misc: pmic: Freescale PMIC switches to generic PMIC driver misc:pmic:samsung Enable PMIC driver at GONI target misc:pmic:max8998 MAX8998 support at a new PMIC driver. misc:pmic:core New generic PMIC driver mx31pdk: Remove unneeded config mx31: provide readable WEIM CS accessor MX51: vision2: Set global macros I2C: Add i2c_get/set_speed() to mxc_i2c.c ARM: Update mach-types devkit8000: Add config to enable SPL MMC boot devkit8000: protect board_mmc_init arm, post: add missing post_time_ms for arm cosmetic, post: Codingstyle cleanup arm, logbuffer: make it compileclean tegra2: Enable MMC for Seaboard tegra2: Add more pinmux functions tegra2: Rename PIN_ to PINGRP_ tegra2: Add more clock functions tegra2: Clean up board code a little tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
2011-10-27GCC4.6: Squash warnings in omap4 clocks.cMarek Vasut
clocks.c:606:2: warning: format '%08x' expects type 'unsigned int', but argument 2 has type 'u32 * const' clocks.c:633:2: warning: format '%08x' expects type 'unsigned int', but argument 2 has type 'u32 * const' Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
2011-10-27GCC4.6: Squash warning in tegra2 board.cMarek Vasut
board.c:43:2: warning: format '%08lX' expects type 'long unsigned int', but argument 2 has type 'u32' Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
2011-10-27ARM: Add Calxeda Highbank platformRob Herring
Add basic support for Calxeda Highbank platform. Only minimal support with serial and SATA are included. Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-27ARM: pantheon: add mmc definitionLei Wen
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-10-27davinci: remove config.mk file from the sourcesVladimir Zapolskiy
To compile TI Davinci SoC support the identical config.mk file from the cpu directory shall be used. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27ARM:AM33XX: Add support for TI AM335X EVMChandan Nath
This patch adds basic support for booting the board. This patch adds support for the UART necessary to get to the u-boot prompt. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27ARM:AM33XX: Added timer supportChandan Nath
This patch adds timer support for AM33xx platform. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27ARM:AM33XX: Add emif/ddr supportChandan Nath
This patch adds AM33xx emif/ddr support along with board specific defines. Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit (git 2.34.1) at 2024-12-27 21:32:43 +0000