| Age | Commit message (Collapse) | Author |
|---|
|
To better support different RAM timings (DDR3-1333 and DDR3-1866 are
assembly options for the RK3399-Q7), this refactors the DTS support
and renames the default DTS variant from rk3399-puma to
rk3399-puma-ddr1600:
- changes the rk3399-puma DTS into a board-specific DTSI by removing
the inclusion of the DRAM timings
- adds a new rk3399-puma-ddr1600.dts, which includes the (new) common
board DTSI and the DDR3-1600 timing DTSI
- wires this up from arch/arm/dts/Makefile and configs/puma-rk3399_defconfig
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The Linux DTS for the RK3399-Q7 has moved with the times... resync
against it to ensure a consistent configuration.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
defines the spl-payload to 256k (0x40000)
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
On the RK3399-Q7, the on-module USB3 hub is held in reset at boot-up
to save power and needs to be woken up using GPIO4A3.
Note that this is not a negated reset-signal (due to a level shifter
being needed for this signal anyway), but a negated enable-signal:
to enable, we need to output LOW (i.e. 0)... so we mark this as an
ACTIVE_LOW signal.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With the validation done for DDR3-1600 (i.e. 800 MHz bus clock), we
add the timings (rk3399-sdram-ddr3-1600.dtsi) and change rk3399-puma.dts
to use these by default.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop blank line at end of file:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The RK3399-Q7 (Puma) DTS should (of course) be dual-licensed.
This updates the licensing info in the rk3399-puma.dts.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The RK3399-Q7 is a system-on-module featuring the Rockchip RK3399
in a Qseven-compatible form-factor.
These changes add a device-tree describing the board and its
interfaces for basic functionality (e.g. GbE, SPI, eMMC, SD-card).
This includes the following changes from the original development:
* dts: rk3399-puma: include DTS for RK3399-Q7 SoM in the Makefile
* dts: rk3399-puma: add gmac for the RK3399-Q7
This change enables the Gigabit Ethernet support on the RK3399-Q7.
* dts: rk3399-puma: use serial0 for stdout
* dts: rk3399-puma: prepare the sdmmc node for SPL booting
* dts: rk3399-puma: enable spi1 and spi5, add /spi1/spiflash
The RK3399-Q7 (Puma) unsually (this is a build-time option for
customised boards) has an on-module SPI-flash connected to SPI1.
As of today, this is a Winbond W25Q32DW (32MBit) device.
The SPI5 controller is routed to the Q7 edge connector and provides
general-purpose SPI connectivity for customer base-boards.
With some minor improvements on integration into our outbound tree
- explicitly modelled the SPI flash as 'spiflash' under spi0
[dts: rk3399-puma: explicitly model spi-flash under spi1]
- renamed the aliases to spi0 and spi1 to allow easier use of
commands and legacy (SPL) infrastructure... i.e. the controllers
will be 0 and 1 for 'sf probe', 'sspi', etc.
[dts: rk3399-puma: rename aliases to number spi as 0 and 1 for commands]
* dts: rk3399-puma: include SPI in the spl-boot-order property
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
