| Age | Commit message (Collapse) | Author |
|---|
|
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Enable the display controller, panel & backlight.
Set panel display timings & set the RGB data bus.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
|
|
Add DT nodes to enable ARM_PL180_MMCI IP support for STM32F746
and STM32F769 discovery boards
There is a hardware issue on these boards, it misses a pullup on the GPIO line
used as card detect to allow correct SD card detection.
As workaround, cd-gpios property is not present in DT.
So SD card is always considered present in the slot.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
FMC driver is now able to discover the bank number by
parsing bank subnodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Also created alias for gpios for stm32f7 discovery board. Based on these
aliases, it would be possible to get gpio devices by sequence.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Also added DT binding doc for stm32 fmc(flexible memory controller).
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
It also removes the qspi pin configuration done during the
board initialization.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
It also removes the ethernet pin configuration done during the board
initialization.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
And remove the uart pin configuration from board initialization.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Also created alias for usart1 and specified oscillator clock for stm32f7
discovery board.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.
Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
|
