summaryrefslogtreecommitdiff
path: root/arch/arm/dts
AgeCommit message (Collapse)Author
2019-04-12ARM: davinci: da850evm: Enable SPL_OF_CONTROL without PLATDATAAdam Ford
With the memory mapping giving us some more avialable RAM, this updates the da850-evm-u-boot.dtsi to include the serial port, SPI and Flash nodes along with some dependent nodes in the SPL dtb. This also removes the platform data initialization code for the serial port and SPI Flash. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12am335x, guardian: Add support for the bosch guardian boardSjoerd Simons
Add support for the Bosch Guardian board. CPU : AM335X-GP rev 2.1 Model: Bosch AM335x Guardian I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Felix Brack <fb@ltec.ch>
2019-04-12ARM: dts: k2g-ice: add dt node for netcpMurali Karicheri
This patch adds dt node for DP83867 phy used on K2G ICE board and also enable netcp device nodes for the board. EVM hardware spec recommends to add 0.25 nsec delay in the tx direction and 2.25 nsec delay in the rx direction for internal delay in the clock path to be on the safer side. The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode 1. Unfortunately, the phy data manual disallows this. Add ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to enable workaround suggested for this incorrect strap setting. This ensures proper operation of this PHY. The dts bindings are kept in sync with that from 4.14.y linux kernel. This required the pinmux device related bindings to be commented out to allow for compilation. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-12ARM: dts: k2g-evm: remove unused phy-mode property from phy nodeMurali Karicheri
This patch removes the unused phy-mode property from the phy dt node. On K2G, currently link-interface determines if phy is used or not and is already set to use rgmii. So this is not needed. Besides phy-mode should be added to slave interface configuration of the cpsw driver, not in the phy node. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-11arm64: dts: ti: k3-am65: add mcu navss nodesGrygorii Strashko
Add DT node for MCU NAVSS its components to get DMA working on AM654 SoC. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-04-11firmware: ti_sci: Add support for NAVSS resource managementGrygorii Strashko
Texas Instruments' System Control Interface (TI-SCI) Message Protocol abstracts management of NAVSS resources, like PSI-L pairing and unpairing, UDMAP tx/rx/flow configuration and Rings. This patch adds support for requesting and configuring such resources from TI-SCI firmware. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Vignesh R <vigneshr@ti.com>
2019-04-11Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Various rmobile fixes
2019-04-09ARM: dts: rmobile: Enable USB on E2 AltMarek Vasut
The E2 Alt board has two USB ports, add missing DT nodes to make the USB available. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-04-09ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0Marek Vasut
Synchronize R-Car Gen3 device trees with Linux 5.0, commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-04-09ARM: dts: rmobile: Synchronize Gen2 DTs with Linux 5.0Marek Vasut
Synchronize R-Car Gen2 device trees with Linux 5.0, commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-04-09ARM: dts: rmobile: Import R8A77965 M3NULCB DTsMarek Vasut
Import R8A77965 M3N ULCB device trees from Linux 5.0 , commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-04-09arm: at91: Add gardena-gateway-at91sam supportStefan Roese
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage. This patch adds support for this board including SPL support. Therefore the AT91Boostrap is not needed on this platform any more. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09arm: at91: at91sam9x5.dtsi: Add watchdog handleStefan Roese
This makes it possible to reference the watchdog DT node via "&watchdog" from board dts files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09board: pm9g45: Migrate to CONFIG_DMIlko Iliev
Migrate the following options to CONFIG_DM: CONFIG_DM_GPIO CONFIG_DM_MMC CONFIG_DM_ETH CONFIG_DM_SERIAL CONFIG_DM_USB Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2019-04-08dts: imx8qxp-mek: Add PHY post reset delayAndrejs Cainikovs
PHY cannot be detected unless we wait about 150 ms. Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-05Merge tag 'u-boot-imx-20190405' of git://git.denx.de/u-boot-imxTom Rini
Fixes for 2019.04 - fix bashism for MX8 - fix ethernet for MX53 - fix docs for i.MX8
2019-04-02DTS: Fix ETH PHY reset on HSC|DDC boards (imx53)Lukasz Majewski
After the commit: "eth: dm: fec: Add gpio phy reset binding" SHA1: efd0b791069af93e9d439a70d1fe2ae8994dbbfa The FEC ETH driver switched to PHY GPIO reset performed with data defined in DTS. For the HSC|DDC boards the GPIO reset signal is active low and hence the wrong DTS description must be changed (otherwise the reset for ETH is not properly setup). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-03-30ARM: dts: rmobile: Activate I2C7 on AltMarek Vasut
Activate I2C7 on Alt to allow access to the PMIC. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-25ARM: dts: rmobile: Increase off-on delay on the SD Vcc regulatorMarek Vasut
An ADATA 16GB Industrial MLC card has so much capacitance on the Vcc pin that the usual toggling of regulator to power the card off and on is insufficient. When the card is calibrated into UHS SDR104 mode, it will remain in that mode across the power cycle and subsequent attempt to communicate with the card will fail. The test with this card is to insert it into an SDHI slot and perform "mmc dev 0 ; mmc dev 0", where the second "mmc dev 0" will fail. Fix this problem by increasing the off-on delay from 0 to 20 mS. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-03-22ARM: fix arch/arm/dts/MakefileMasahiro Yamada
Since commit 27cb7300ffda ("Ensure device tree DTS is compiled"), build succeeds irrespective of the correctness of Makefile. In fact, you can compile any defconfig without adding any entry in arch/*/dts/Makefile. As a result, a lot of wrong code have been merged unnoticed. I am going to revert that commit, and lots of hidden issues have come to light: [1] Typos armada-3720-uDPU.dts, sun8i-a83t-tbs-a711.dts use the extension ".dts" instead of ".dtb" [2] DTB is associated to undefined CONFIG option For example, mx6sllevk_defconfig defines CONFIG_MX6SLL, but associates its device tree to CONFIG_MX6SL, which is undefined. [3] Lots of entries are missing Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> [trini: add imx6ul pico dtbs] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-03-19Merge git://git.denx.de/u-boot-marvellTom Rini
- Enable network interface on clearfog_gt_8k (Baruch) - Fix dreamplug boot by adding an spi0 alias to the DT (Chris) - Fix / enhance Marvell ddr3 setup / parameters (Chris) - Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris) - Enable SPL_FLASH_BAR on db-88f6820-amc (Chris) - Use correct pcie controller name in Armada-38x dts files (Chris) - Disable d-cache on Kirkwood platforms as currently needed (Chris) - Add a more descriptive comment to pci_mvebu.c (Stefan) - Update Marvell maintainers entry (Stefan)
2019-03-19ARM: mvebu: use correct name for pcie controllerChris Packham
When armada-385.dtsi was sync'd from Linux the name of the node describing the pcie controller was changed from pcie-controller to pcie. Some of the boards that include armada-385.dtsi were missed in the update retaining the old name. This updates the affected boards. Reported-by: Влад Мао <vlaomao@gmail.com> Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-03-19ARM: kirkwood: add spi0 alias for dreamplugChris Packham
The conversion to DM_SPI managed to break accessing the environment on dreamplug. This is because the environment code relies on being to able to select the SPI device based on the sequence number. Add an alias so that the spi0 bus gets sequence number 0. Reported-by: Leigh Brown <leigh@solinno.co.uk> Signed-off-by: Chris Packham <judge.packham@gmail.com> Tested-by: Leigh Brown <leigh@solinno.co.uk> Signed-off-by: Stefan Roese <sr@denx.de>
2019-03-16ARM: dts: socfpga: Add missing altr,sysmgr-syscon for EMACLey Foon Tan
Syscon register is required in dts to select correct PHY interface. Fix error below: Net: Failed to get syscon: -2 Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2019-03-14Merge branch 'master' of git://git.denx.de/u-boot-samsungTom Rini
2019-03-13arm: dts: imx6qdl-u-boot: Enable spba-bus@2000000 simple busAdam Ford
spba-bus has a few nodes under it including the UART1 and some ESPI buses. In order to use them in SPL, the u-boot,dm-spl flag needs to be added to the spba-bus@2000000 container. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-03-13pico-imx6ul: Import dts files from kernelFabio Estevam
Import the device tree files from kernel 5.0-rc6 in preparation for driver model conversion. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2019-03-11arm: dts: exynos: Adjust whitespace around status propertyKrzysztof Kozlowski
Just add spaces around '=' sign for clarity. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2019-03-11arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid XU3 familyKrzysztof Kozlowski
Add startup time to LDO regulators of S2MPS11 PMIC on Odroid XU3/XU4/HC1 family of boards to be sure the voltage is proper before relying on the regulator. The datasheet for all the S2MPS1x family is inconsistent here and does not specify unambiguously the value of ramp delay for LDO. It mentions 30 mV/us in one timing diagram but then omits it completely in LDO regulator characteristics table (it is specified for bucks). However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12 mV/us or 24 mV/us. Without the ramp delay value the consumers do not wait for voltage settle after changing it. Although the proper value of ramp delay for LDOs is unknown, it seems safer to use at least some value from reference kernel than to leave it unset. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Tested-by: Anand Moon <linux.amoon@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2019-03-11arm: dts: exynos: Add supply for ADC block to Odroid XU3 familyKrzysztof Kozlowski
The ADC block requires VDD supply to be on so provide one. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Tested-by: Anand Moon <linux.amoon@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2019-03-09ARM: dts: rmobile: Zap redundant USB/SDHI nodes on M3NEugeniu Rosca
v2019.01 commit cbff9f80cedd ("ARM: dts: rmobile: Sync Gen3 DTs with Linux 4.19.6") made the sdhi/usb nodes available in r8a77965.dtsi. Hence, remove the SDHI/USB nodes from r8a77965-u-boot.dtsi. This is equivalent to partially reverting below v2019.01 commits: - f529bc551b6d ("ARM: dts: rmobile: Extract USB nodes on M3N") - 830b94f76867 ("ARM: dts: rmobile: Extract SDHI nodes on M3N") Duplicating the nodes from <soc>.dtsi to <soc>-u-boot.dtsi is obviously: - not needed if no U-boot-specific changes are needed in those nodes. - potentially dangerous/error-prone, since the duplicated properties override the properties originally defined in <soc>.dtsi. One possible consequence is that <soc>.dtsi is getting an update from Linux, while <soc>-u-boot.dtsi stays unchanged. In this situation, the obsolete property values from <soc>-u-boot.dtsi will take precedence masking some of the <soc>.dtsi updates, potentially leading to all kind of obscure issues. Below is the dtdiff of r8a77965-salvator-x-u-boot.dtb (the only "user" of r8a77965-u-boot.dtsi) before and after the patch (slightly reformatted to avoid 'git am/apply' issues and to reduce the width). What below output means is there is already a mismatch in some of SDHI/USB nodes between r8a77965.dtsi and r8a77965-u-boot.dtsi. Since no U-Boot customization is needed in SDHI/USB DT nodes, get rid of them in r8a77965-u-boot.dtsi. $> dtdiff before-r8a77965-salvator-x-u-boot.dtb \ after-r8a77965-salvator-x-u-boot.dtb --- /dev/fd/63 2019-03-09 12:57:40.877963983 +0100 +++ /dev/fd/62 2019-03-09 12:57:40.877963983 +0100 @@ -1471,7 +1471,7 @@ bus-width = <0x4>; cd-gpios = <0x51 0xc 0x1>; clocks = <0x6 0x1 0x13a>; - compatible = "renesas,sdhi-r8a77965"; + compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi"; interrupts = <0x0 0xa5 0x4>; max-frequency = <0xc65d400>; pinctrl-0 = <0x4d>; @@ -1492,7 +1492,7 @@ sd@ee120000 { clocks = <0x6 0x1 0x139>; - compatible = "renesas,sdhi-r8a77965"; + compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi"; interrupts = <0x0 0xa6 0x4>; max-frequency = <0xbebc200>; power-domains = <0x1 0x20>; @@ -1504,7 +1504,7 @@ sd@ee140000 { bus-width = <0x8>; clocks = <0x6 0x1 0x138>; - compatible = "renesas,sdhi-r8a77965"; + compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi"; fixed-emmc-driver-type = <0x1>; interrupts = <0x0 0xa7 0x4>; max-frequency = <0xbebc200>; @@ -1526,7 +1526,7 @@ bus-width = <0x4>; cd-gpios = <0x5a 0xf 0x1>; clocks = <0x6 0x1 0x137>; - compatible = "renesas,sdhi-r8a77965"; + compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi"; interrupts = <0x0 0xa8 0x4>; max-frequency = <0xc65d400>; pinctrl-0 = <0x56>; @@ -1868,14 +1868,14 @@ usb-phy@ee0a0200 { #phy-cells = <0x0>; - clocks = <0x6 0x1 0x2be>; + clocks = <0x6 0x1 0x2bf>; compatible = "renesas,usb2-phy-r8a77965", "renesas,rcar-gen3-usb2-phy"; phandle = <0x47>; pinctrl-0 = <0x4c>; pinctrl-names = "default"; power-domains = <0x1 0x20>; reg = <0x0 0xee0a0200 0x0 0x700>; - resets = <0x6 0x2be>; + resets = <0x6 0x2bf>; status = "okay"; }; Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
2019-03-09ARM: dts: rmobile: Force 1-bit bus width on Gen2 QSPIMarek Vasut
U-Boot currently uses Gen2 QSPI in 1-bit mode, enforce it until we can do better using the new SPI NOR framework. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-02-28Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- Various Bananapi fixes
2019-02-20Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2019-02-20Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
- Support of NXP's LX2160RDB and LX2160QDS platform - Enable SATA DM model for NXP's ARM SoCs
2019-02-20ARM: tegra: enable ums on nyan boardsTristan Bastian
This patch enables UMS on the nyan devices like the nyan-big. A patch like this has been sent in by Stephen Warren some time ago for other tegra devices: commit e6607cffef965011ef0ddc0fbe6f4b7c0d53aeec. But the nyan devices never received that functionality. Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-02-20nyan-big: change spi delayTristan Bastian
Internal keyboard of nyan-big is only working when cold booting by pressing [reload/refresh]+[power] button. With this patch keyboard is working by only pressing [power] button. Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-02-19ARM: omap3: evm: Update DM SPL supportDerald D. Woods
- Switch to using the omap3-u-boot.dtsi file for needed properties - Enable SPL_OF_CONTROL This commit is based on the following series: https://patchwork.ozlabs.org/project/uboot/list/?series=92472 https://patchwork.ozlabs.org/project/uboot/list/?series=92462 Signed-off-by: Derald D. Woods <woods.technical@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-19omap3_beagle: Update for DM SPL supportTom Rini
- Switch to using the omap3-u-boot.dtsi file for needed properties. - Remove a few SPL features to free up more SRAM space. - Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to worry about X-Loader at this point anymore. - A few related updates to SPL options as part of switching to DM SPL. Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2019-02-19ARM: omap3_logic: Enable SPL booting device treeAdam Ford
With the generic omap3-u-boot.dtsi file available, this patch increased the memory of the various incarnations of the omap3_logic board, and points their respective u-boot.dtsi files to the newly created generic one, and removes the PLATDATA from the board file. These are all done at once because the're all utilizing the same omap3logic.c board file. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-19ARM: DTS: omap3-u-boot.dtsiAdam Ford
Create generic omap3-u-boot.dtsi file that omap3 based boards can include to generate device tree in SPL for booting MLO. Credit should go to Tom Rini. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2019-02-19board/BuR/brxre1: convert do DMHannes Schmelzer
This commit converts the brxre1 board to DM, for this we have todo following things: - add a devicetree-file for this board - drop all obsolete settings from board header-file - use dm_i2c_xxx calls for read/write to the resetcontroller - request gpios before operate them Serues-cc: trini@konsulko.com Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-02-19lx2160aqds : Add support for LX2160AQDS platformPankaj Bansal
LX2160AQDS is a development board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [PK: Sqaush patch for "secure boot defconfig" & add maintainer] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: lx2160ardb : Add support for LX2160ARDB platformPriyanka Jain
LX2160ARDB is an evaluation board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Peng Ma <peng.ma@nxp.com> Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> [PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han and re-arrange defconfig] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-18sunxi: Add Bananapi M2+ H5 boardChen-Yu Tsai
As the H5 is pin compatible with the H3, vendors tend to upgrade their existing H3 products with an H5 SoC swap. This is the case with the Bananapi M2+ H5. Add the following to support it: - device tree file: synced from Linux v5.0-rc1, - defconfig: copy of bananapi_m2_plus_h3_defconfig with only SoC family and default device tree file name changed - MAINTAINERS entry Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-02-18sunxi: Sync Bananapi M2+ device tree from Linux v5.0-rc1Chen-Yu Tsai
As of commit aa8fee415f46 ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus") in the Linux kernel, the device tree for the Bananapi M2+ has been split into a common dtsi file, and an SoC-specific board device tree file that includes both the shared dtsi file and the soc dtsi file. This was done to support both the H3 and H5 variants of the same board. This is similar to what was done for the Libre Computer ALL-H3-CC in U-boot commit d7b17f1c24af ("sunxi: Split out common board design for ALL-H3-CC device tree"). The newly split files are directly synced from Linux tag v5.0-rc1. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-02-16Merge tag 'u-boot-imx-2019-02-16' of git://git.denx.de/u-boot-imxTom Rini
u-boot-imx-2019-02-16 --------------------- - vhybrid: add calibration - gw_ventana: fixes - Improve documentation for Secure Boot (HABv4) - Fix Marvell Switch - MX6 Sabre, switch to DM - Fixes for NAND
2019-02-15ARM: dts: i.MX6Q, i.MX6QDL: fix address/size-cells warningsMarcel Ziswiler
This fixes the following warnings: arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /clocks: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/aips-bus@02100000/mipi@021e0000: unnecessary #address-cells/ #size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02400000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02400000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02800000/port@2: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size): /soc/ipu@02800000/port@3: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-02-15arm: dts: Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd]Abel Vesa
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones from kernel v4.20 (commit 8fe28cb58bcb2). Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15arm: dts: Add all the imx6[q|qp|dl] sabre[auto|sd] u-boot dts[i] filesAbel Vesa
This allows us to keep the basic dts[i] files up-to-date with the ones in kernel, but at the same time allowing the u-boot to add its own properties to the existing nodes. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-26 09:10:04 +0000