summaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-fsl-layerscape
AgeCommit message (Collapse)Author
2020-01-24arch: armv8: fsl-layerscape: export serdes config to environmentAlex Marginean
Exports the serdes configuration as an environment variable for LS gen 3 SoCs, so it can be used in u-boot command line. It should particularly be useful for applying Linux DT overlays for the given serdes configuration. This code is called from arch_misc_init and not from the existing serdes_init function because it depends on U-Boot environment being set up. Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26armv8: lx2160a: Add FSL_PEX_STREAM_ID_END for LX2160AWasim Khan
Add FSL_PEX_STREAM_ID_END and remove FSL_PEX_STREAM_ID_NUM for lx2160a. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26fsl-lsch3: soc: Enable AHB read support for Flexspi controllerKuldeep Singh
Enable AHB support for Flexspi controller interface meaning memory can be accessed via md command using absolute addresses Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26fsl-lsch3: Add FlexSPI address space in immap_lsch3Kuldeep Singh
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
2019-12-26ls1028a: Configure stream IDs for integrated PCI and fix up Linux DTAlex Marginean
Hardware comes out of reset with implicit values, but these are outside the accepted range for Layerscape gen 3 chassis spec used on LS1028A. Allocate different IDs and fix up Linux DT to use them. Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26armv8: Add workaround for USB erratum A-050106Ran Wang
USB3.0 Receiver needs to enable fixed equalization for each of PHY instances in an SOC. This is similar to erratum A-009007, but this one is for LX2160A, and the register value is different. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-27arm: drop eSDHC clock getting in mxc_get_clock() for layerscapeYangbo Lu
Although layerscape platforms reuse mxc_get_clock() of i.MX platforms, eSDHC clock getting do not have to use it. It uses global data gd->arch.sdhc_clk directly in fsl_esdhc driver. Even there are more than one eSDHC controllers on SoC, they use same reference clock. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08armv8: ls1028a: add erratum A-050382 workaroundLaurentiu Tudor
Erratum A-050382 states that the eDMA ICID programmed in the eDMA_AMQR register in DCFG is not correctly forwarded to the SMMU. The workaround consists in programming the eDMA ICID in the eDMA_AMQR register in DCFG to 40. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08armv8: lx2160a: add icid setup for platform devicesLaurentiu Tudor
Add ICID setup for the platform devices contained on this chip: usb, sata, sdhc, sec. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08fsl-layerscape: add missing SATA3 and SATA4 base addressesLaurentiu Tudor
LX2160A chips have 4 sata controllers. Add missing base addresses for SATA3 and SATA4. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08fsl-layerscape: fix compile error with sec fw disabledLaurentiu Tudor
If SEC FW support is not enabled (ARMV8_SEC_FIRMWARE_SUPPORT=n), below compilation error appears arch/arm/include/asm/arch-fsl-layerscape/fsl_icid.h:169:4: error: 'CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT' undeclared here (not in a function) Fix it by wrapping with CONFIG_IS_ENABLED(). Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-21armv8: Update LX2160A/LX2120A/LX2080A SVR valueWasim Khan
LX2160A/LX2120A/LX2080A SVR value should be 0x873600/0x873620/0x873602 Previous values were valid only if CAN fuse is blown. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-21armv8: ls1028a: disable multimedia for ls1027a, ls1017aYuantian Tang
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a. Both ls1027a and ls1017a personalities are lower functionality version which doesn't support the multimedia subsystems, like LCD, GPU. To disable multimedia feature on non-multimedia version, set the status property to disabled in dts nodes. Signed-off-by: Tang Yuantian <andy.tang@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-21armv8: fsl-layerscape: Make USB masters snoopableRan Wang
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write snoop signal on LS1043A and LS1046A. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-21armv8: ls1028a: Add more personalities supportYuantian Tang
Add LS1027A, LS1018A and LS1017A personalities support to LS1028A SoC family. LS1028A is the prime personality of LS1028A SoC family. LS1027A is a lower funtionality version of QorIQ LS1028A which does not support the multimedia subsystems, such as LCD controller, GPU, and eDP PHY. The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72 core, low power versions of the QorIQ LS1028A and LS1027A SoCs respectively. Signed-off-by: Tang Yuantian <andy.tang@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12fsl-layerscape: Add fsl_esdhc peripheral clock supportYinbo Zhu
Add esdhc peripheral clock support for NXP layerscape platforms: LS1046ARDB, LS1043ARDB, LS1012ARDB, LS1028ARDB, LS1088ARDB, LX2160ARDB Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-08-22armv8: ls1028a: add icid setup for platform devicesLaurentiu Tudor
Add ICID setup for the platform devices contained on this chip: usb, sata, sdhc, edma, qdma, gpu, display and sec. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1088a: add icid setup for platform devicesLaurentiu Tudor
Add ICID setup for the platform devices contained on this chip: usb, sata, sdhc, sec. The ICID macros for SEC needed to be adapted because the format of the registers is different. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: fsl-layerscape: make icid setup endianness awareLaurentiu Tudor
The current implementation assumes that the registers holding the ICIDs are universally big endian. That's no longer the case on newer platforms so update the code to take into account the endianness of each register. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: fsl-layerscape: add base addresses for several devicesLaurentiu Tudor
Add CCSR base addresses for ESDHC2, EDMA QDMA, DISPLAY and GPU devices. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: fsl-layerscape: add missing sec jr base address definesLaurentiu Tudor
Add defines for all the SEC job rings base addresses. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22drivers: i2c: mxc: Fix compiler error when using i2c dm modeChuanhua Han
I2C dm mode enablemenet causes below compilation errors: In file included from include/config.h:8:0, from include/common.h:20: include/config_fallbacks.h:51:4: error: #error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" # error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" ^~~~~ In file included from include/config.h:8:0, from include/common.h:20: include/config_fallbacks.h:51:4: error: #error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" # error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" ^~~~~ board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f': board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'? [-Wimplicit-function-declaration] i2c_early_init_f(); ^~~~~~~~~~~~~~~~ arch_early_init_r drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe': drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function 'enable_i2c_clk'; did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration] ret = enable_i2c_clk(1, bus->seq); ^~~~~~~~~~~~~~ enable_irq_wake So fix these compilation errors. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19arm: ls1028a: define the integrated PCI bus (ECAM)Alex Marginean
LS1028A includes an integrated PCI bus with 11 PCI functions residing on bus 0. ECAM plus the device register space takes up 256MB of address space. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19armv8: fsl-lsch3: add clock support for the second eSDHCYangbo Lu
Layerscape began to use two eSDHC controllers, for example, LS1028A. They are same IP block with same reference clock. This patch is to add clock support for the second eSDHC. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19armv8: ls1028a: Add other serdes protocal supportXiaowei Bao
Add other serdes protocal support. Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19armv8: ls1028a: enable workaround for USB erratum A-008997Ran Wang
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL registers has been moved to DSCR as compared to other Layerscape SoCs where it was in SCFG. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-22armv8: ls1028a: Add NXP LS1028A SoC supportYuantian Tang
Ls1028a SoC is based on Layerscape Chassis Generation 3.2 architecture with features: 2 ARM v8 Cortex-A72 cores, CCI400, SEC, DDR3L/4, LCD, GPU, TSN ENETC, 2 USB 3.0, 2 eSDHC, 2 FlexCAN, 2 SPI, SATA, 8 I2C controllers, 6 LPUARTs, GPIO, SAI, qDMA, eDMA, GIC, TMU etc. Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com> Signed-off-by: Rai Harninder <harninder.rai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Signed-off-by: Tang Yuantian <andy.tang@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-22armv8: lx2160a: add MMU table entries for PCIeHou Zhiqiang
The lx2160a have up to 6 PCIe controllers and have different address and size of PCIe region. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-22armv8: fsl-layerscpae: correct the PCIe controllers' region sizeHou Zhiqiang
The LS2080A has 8GB region for each PCIe controller, while the other platforms have 32GB. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03armv8: fsl-layerscape: avoid DT fixup warningLaurentiu Tudor
sec_firmware reserves JR3 for it's own usage and deletes the JR3 node from the device tree. This causes this warning to be issued when doing the device tree fixup: WARNING could not find node fsl,sec-v4.0-job-ring: FDT_ERR_NOTFOUND. Fix it by excluding the device tree fixup for the JR reserved by sec_firmware. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03armv8: fsl-layerscape: fix SEC QI ICID setupLaurentiu Tudor
The SEC QI ICID setup in the QIIC_LS register is actually an offset that is being added to the ICID coming from the qman portal. Setting it with a non-zero value breaks SMMU setup as the resulting ICID is not known. On top of that, the SEC QI ICID must match the qman portal ICIDs in order to share the isolation context. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geanta <horia.geanta@nxp.com> Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: layerscape: move TZASC and TZPC configs to KconfigRajesh Bhagat
Moves FSL_TZASC_400 and FSL_TZPC_BP147 configs to Kconfig for LS1088A and LS2088A platforms. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19lx2160aqds : Add support for LX2160AQDS platformPankaj Bansal
LX2160AQDS is a development board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [PK: Sqaush patch for "secure boot defconfig" & add maintainer] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: lx2160a: Update CONFIG_SYS_FSL_PEBUF_BASEPriyanka Jain
As per hardware documentation, CONFIG_SYS_FSL_PEBUF_BASE for lx2160a is 0x1c00000000 Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-17armv8: fsl-layerscape: properly configure qdma ICIDLaurentiu Tudor
The ICIDs for the qdma device are not configured through SCFG but through some registers found in the actual device register block. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1043a: add SVR definitions for 23x23 package siliconHou Zhiqiang
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: lx2160a: Add LX2160A SoC SupportPriyanka Jain
LX2160A Soc is based on Layerscape Chassis Generation 3.2 architecture with features: 16 ARM v8 Cortex-A72 cores in 8 cluster, CCN508, SEC, 2 64-bit DDR4 memory controller, RGMII, 8 I2C controllers, 3 serdes modules, USB 3.0, SATA, 4 PL011 SBSA UARTs, 4 TZASC instances, etc. SoC personalites: LX2120A is SoC with Twelve 64-bit ARM v8 Cortex-A72 CPUs LX2080A is SoC with Eight 64-bit ARM v8 Cortex-A72 CPUs Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8:fsl-layerscape: Add support for Chassis 3.2Priyanka Jain
NXP layerscape architecture Chassis 3.2 builds upon chassis3 architecture with changes like DDR Memory map change, removal of IFC and support of upto 8 I2C controller. Patch add README.lsch3_2 and the above changes under macro CONFIG_NXP_LSCH3_2. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: lsch3: Add support of serdes3 modulePriyanka Jain
Some lsch3 based SoCs like lx2160a contains three serdes modules. Add support for third serdes protocol in lsch3 Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: fsl-layerscape: Update parsing boot sourceYork Sun
Workaround of erratum A010539 clears the RCW source field in PORSR1 register, causing failure of detecting boot source using this method. Use SMC call if U-Boot runs at EL2. If SMC is not implemented or running at EL3, continue to read PORSR1 and presume QSPI as boot source if erratum workaround A010539 is enabled and RCW source is cleared. Signed-off-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: layerscape: add SMC calls for DDR size and bank infoRajesh Bhagat
Adds SMC calls for getting DDR size and bank info for TFABOOT. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: fsl-layerscape: identify boot source from PORSR registerRajesh Bhagat
PORSR register holds the cfg_rcw_src field which can be used to identify boot source. Further, it can be used to select the environment location. Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> [YS: fix multiple checkpatch issues] Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-04move data structure out of cpu.hYork Sun
Move static definitions to cpu.c file, as it doesn't allow the cpu.h file to be included in multiple c files. Signed-off-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: add icid setup supportLaurentiu Tudor
Reuse the existing ICID setup code done for LS1046A smmu enablement and add the equivalent setup for LS1043A chips. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: advertise QMan v3 in configurationLaurentiu Tudor
The QMan IP block in this SoC is version 3.2 so advertise this in the SoC configuration header. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: fsl-layerscape: add missing qe base address defineLaurentiu Tudor
Add define for QUICC Engine register block base address. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> [York S: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27u-boot: fixup the iommu-map property of fsl-mc nodeNipun Gupta
The iommu-map property in the fsl-mc node is updated by valid stream-ids by u-boot. This patch is to fixup this property for LS208x and LS1088. Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-08-10armv8: layerscape: Enable EHCI access for LS1012ARan Wang
Program Central Security Unit (CSU) to grant access to USB 2.0 controller. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: rewrite commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-08-10armv8: layerscape: move ns_dev[] define from h to c file.Ran Wang
Move ns_dev[] from header file to C file to avoid compiling warning when header file is included by others. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: rewrite commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-08-10armv8: ls1046a: setup SEC ICIDs and fix up device treeLaurentiu Tudor
Add support for SEC ICID configuration and apply it for ls1046a. Also add code to make the necessary device tree fixups. Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-26 21:38:30 +0000