| Age | Commit message (Collapse) | Author |
|---|
|
Add support for Vybrid's UART2 (Colibri UART_B).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
|
|
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
|
|
This driver adds support for the USB peripheral on Freescale Vybrid
SoC's.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
|
|
Enable the SCSC (Slow Clock Source Controller) and select the external
32KHz oscillator. This improves the accuracy of the RTC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
|
|
Add NFC (NAND Flash Controller) clock support and enable them
at board initialization time.
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
|
|
This patch contains several changes required for second Ethernet
(enet1/RMII1) port on vf610
- ANADIG PLL5 control definitions required for Ethernet RMII1 clock
- Secondary Ethernet (enet1) MAC RMII1 base address definition
- RMII1 iomux definitions
- VF610_PAD_PTA6__RMII0_CLKOUT iomux definition required for
internal (e.g. crystal-less) Ethernet clocking.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
Add CCM_CCGR0_UART0_CTRL_MASK clock definition and add TX/RX iomux
definitions for UART0 (aka. SCI0).
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
The anadig_reg structure started at the wrong offset (fixed by adding
reserved_0x000[4]), was missing some reserved field required for
alignment purpose (reserved_0x094[3] between pll4_denom and pll6_ctrl)
and further contained a too short reserved field causing further miss-
alignment (reserved_0x0C4[7]). Also, rename all the reserved fields
and using a memory offset based scheme for.
Discovered and tested by temporarily putting the following debug
instrumentation into board_init():
struct anadig_reg *anadig = (struct anadig_reg *)ANADIG_BASE_ADDR;
printf("&anadig->pll3_ctrl=0x%p\n", &anadig->pll3_ctrl);
printf("&anadig->pll5_ctrl=0x%p\n", &anadig->pll5_ctrl);
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch adds I2C support for Vybrid VF610 platform and adds
I2C0 support to VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
This patch adds generic codes to support Freescale's Vybrid VF610 CPU.
It aligns Vybrid VF610 platform with i.MX platform. As there are
some differences between VF610 and i.MX platforms, the specific
codes are in the arch/arm/cpu/armv7/vf610 directory.
Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
