| Age | Commit message (Collapse) | Author |
|---|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add the dump of DRAM PLL into "clocks" command
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
|
|
For ARM core clock, there are two input branches, and can select via mux:
one from ARM PLL directly, second from CCM A53 clock root.
Currently we are using second branch. But IC confirmed the CCM A53 root
signoff timing is 1Ghz, so we should switch to input from ARM PLL directly.
This patch fixes the CORE SEL slice configuration and switch ARM clock
to ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
iMX8MQ EVK board has a eMMC5.0 chip and supports SD3.0, so enable the UHS
and HS400 configs to enhance the eMMC/SD access.
The change also needs to set usdhc clock to 400Mhz, and add the
off-on-delay-us to SD reset pin, otherwise some SD cards will
fail to select UHS mode in re-initialization.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Since frac_pll_init() is only used in this file, change it to 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous
prototype for ‘frac_pll_init’ [-Wmissing-prototypes]
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
Function sscg_pll_init() is not used anywhere, so it can simply be deleted.
This was found because of the following sparse
warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes]
int sscg_pll_init(u32 pll)
^~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
Since do_imx8m_showclocks() is only used inside this file, make it 'static'.
This fixes the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype
for ‘do_imx8m_showclocks’ [-Wmissing-prototypes]
int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
Function init_usb_clk() is not used anywhere, so it can simply be deleted.
This was detected by the following sparse warning:
arch/arm/mach-imx/imx8m/clock_imx8mq.c:377:6: warning: no previous prototype
for ‘init_usb_clk’ [-Wmissing-prototypes]
void init_usb_clk(void)
^~~~~~~~~~~~
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
|
|
fsl_esdhc_imx driver will call "mxc_get_clock(MXC_ESDHC_CLK +
dev->seq)", however mxc_get_clock wrongly handle MXC_ESDHC_CLK
as root clk and cause sd card could not be detected in U-Boot proper,
as below:
"Loading Environment from MMC... unable to select a mode"
Handle MXC_ESDHC_CLK in mxc_get_clock to fix the issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Fabio Estevam <festevam@gmail.com>
|
|
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Improve the IRQ response latency by setting GIC root clock source to
sys_pll2_200m from osc.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id.
It returns a magic number 0xff0055aa. update get_cpu_rev to support it,
and enable ocotp clock to access ocotp.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MQ and i.MX8MM use different analog pll design, but they
share same ccm design.
Add clock_imx8mq.h for i.MX8MQ
keep common part in clock.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8MQ and i.MX8MM has totally different pll design, so
rename clock to clock_imx8mq.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
