summaryrefslogtreecommitdiff
path: root/arch/arm/mach-imx/imx8m
AgeCommit message (Collapse)Author
2019-11-03imx: imx8mq: add init_nand_clkPeng Fan
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF, so we still use legacy mode to configure the clock. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx8m: clock: improve irq response latencyPeng Fan
Improve the IRQ response latency by setting GIC root clock source to sys_pll2_200m from osc. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx8m: imx8mq: get chip rev for B1 revisionPeng Fan
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id. It returns a magic number 0xff0055aa. update get_cpu_rev to support it, and enable ocotp clock to access ocotp. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HABStefano Babic
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross architecture purposes. If Secure Boot is required for imx, this means to enable and use the HAB processor in the soc. Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-10-08imx: Add i.MX8MM EVK board support.Peng Fan
Add board and SoC dts Add ddr training code support SD/MMC/GPIO/PINCTRL/UART Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: soc: probe clock device in arch_cpu_init_dmPeng Fan
Because we need to get cpu freq in print_cpuinfo at very early stage, so we need to make sure the ccm be probed. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: add clk support for i.MX8MMPeng Fan
Introduce clk implementation for i.MX8MM, including pll configuration, ccm configuration. Mostly will be done clk dm driver, but such as DRAM part, we still use non clk dm driver, because we have limited sram. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: restructure clock.hPeng Fan
i.MX8MQ and i.MX8MM use different analog pll design, but they share same ccm design. Add clock_imx8mq.h for i.MX8MQ keep common part in clock.h Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: rename clock to clock_imx8mqPeng Fan
i.MX8MQ and i.MX8MM has totally different pll design, so rename clock to clock_imx8mq. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: restrict reset_cpuPeng Fan
Make reset_cpu only visible when CONFIG_SYSRESET not defined or CONFIG_SPL_BUILD. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: soc: enable SCTR clock before timer initPeng Fan
To i.MX8MM SCTR clock is disabled by ROM, so before timer init need to enable it. To i.MX8MQ, it does not hurt the clock is enabled again. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: Configure trustzone region 0 for non-secure accessYe Li
Set trustzone region 0 to allow both non-secure and secure access when trust zone is enabled. We found USB controller fails to access DDR if the default region 0 is secure access only. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: set BYPASS ID SWAP to avoid AXI bus errorsPeng Fan
set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to generated AXI bus errors with TZC380 enabled. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: Fix MMU table issue for OPTEE memoryPeng Fan
When running with OPTEE, the MMU table in u-boot does not remove the OPTEE memory from its settings. So ARM speculative prefetch in u-boot may access that OPTEE memory. Due to trust zone is enabled by OPTEE and that memory is set to secure access, then the speculative prefetch will fail and cause various memory issue in u-boot. The fail address register and int_status register in trustzone has logged that speculative access from u-boot. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: add get_cpu_rev support for i.MX8MMPeng Fan
There are several variants based on i.MX8MM, add the support in get_cpu_rev Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: add IMX8MM kconfig entryPeng Fan
Add IMX8MM kconfig entry Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: add IMX8MQ kconfig entryPeng Fan
Add IMX8MQ kconfig entry, preparing support IMX8MM Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8m: add image cfg for i.MX8MM lpddr4Peng Fan
There is no HDMI on i.MX8MM, so we need to remove HDMI entry, then we could not reuse imximage.cfg, so create a new one. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25imx: i.MX8MQ: clear ocotp error bitPeng Fan
In case ocotp error bit is set, clear it. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-09imx8m: clock: Fix oscillator valuesFabio Estevam
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return 32768Hz to reflect the reality. This also keeps the values in sync with the Linux clock tree. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-01-01imx: add i.MX8MQ EVK supportPeng Fan
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to DRAM. The boot log with Arm trusted firmware console enabled: " U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) PMIC: PFUZE100 ID=0x10 Normal Boot Trying to boot from MMC2 NOTICE: Configureing TZASC380 NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty NOTICE: BL31: Built : 09:28:54, Nov 8 2018 lpddr4 swffc start NOTICE: sip svc init U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz Reset cause: POR Model: Freescale i.MX8MQ EVK DRAM: 3 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: Warning: ethernet@30be0000 using MAC address from ROM eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 " Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-01imx: imx8m: introduce imximage cfg filePeng Fan
imximage.cfg will be used to generate the flash.bin Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-01imx: imx8m: clock refactor dram pll partPeng Fan
Refactor dram_pll_init to accept args to configure different pll freq. Introduce dram_enable_bypass and dram_disable_bypass Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-01imx: rename mx8m,MX8M to imx8m,IMX8MPeng Fan
Rename mx8m,MX8M to imx8m,IMX8M Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Jon Nettleton <jon@solid-run.com>
generated by cgit (git 2.34.1) at 2024-12-26 10:46:29 +0000