summaryrefslogtreecommitdiff
path: root/arch/arm/mach-imx
AgeCommit message (Collapse)Author
2020-05-01imx: imx8m: Don't use the addr parameter of reset_cpuClaudius Heine
imx8m has the only implementation of `reset_cpu` which does not ignore the addr parameter and instead gives it some meaning as the base address of watchdog registers. This breaks convention with the rest of U-Boot where the parameter is ignored and callers are passing in 0. Fixes: d2041725e84b ("imx8m: restrict reset_cpu") Co-Authored-by: Harald Seiler <hws@denx.de> Signed-off-by: Claudius Heine <ch@denx.de> Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
2020-05-01imx8: Configure SNVSFranck LENORMAND
Add a module to configure the tamper and secure violation of the SNVS using the SCU API. The module also adds some commands: - snvs_cfg: Configure the SNVS HP and LP registers - snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP) - tamper_pin_cfg: Change the configuration of the tamper pins - snvs_clear_status: Allow to write to LPSR and LPTDSR to clear status bits Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8m: Enable WDOG_B for timeoutYe Li
When doing reset_cpu, in normal case the WDOG_B outputs immediately after we clean WDA bit. But on mscale, the WDOG_B may be later than internal reset, and cause PMIC not reset. As we enabled the SD3.0 support, the PMIC must be reset to reset SD card. Change the reset_cpu to enable the WDOG_B for timeout as well, and set WDOG timeout to 1s. Reviewed-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8mm: clock: fix fracpll decode issueYe Li
The fracpll decoding is using the bit definitions for int pll. Most of them are same, but the CLKE bit is different. Fix the wrong CLKE_MASK for fracpll and correct all bit definitions in fracpll decoding. Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8: parser: fix some bad debug message formatingPeng Fan
In SPL build, the formatting '%llx' in debug() is not supported. Also, fix some misplaced parameters in printf. Modified from Seb Fagard's downstream patch Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8: ahab: fix some bad debug message formatingSeb Fagard
In SPL build, the formatting '%llx' in debug() is not supported. Also, fix some misplaced parameters in printf. Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Seb Fagard <sebastien.fagard@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8: ahab: fix 'end address' parameter of rm_find_memregPeng Fan
parameter 'end address' must be inclusive of address range. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8: Change to use new SECO API commandsYe Li
Latest SCFW has removed old MISC SECO commands. So update the codes to use new SECO commands. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8: parser: fix 'end address' parameter of rm_find_memregPeng Fan
parameter 'end address' must be inclusive of address range. Modified from Seb's downstream patch. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8m: Dump DRAM PLL rate by clocks commandYe Li
Add the dump of DRAM PLL into "clocks" command Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com>
2020-05-01imx8mq: Set ARM core clock directly from ARM PLLPeng Fan
For ARM core clock, there are two input branches, and can select via mux: one from ARM PLL directly, second from CCM A53 clock root. Currently we are using second branch. But IC confirmed the CCM A53 root signoff timing is 1Ghz, so we should switch to input from ARM PLL directly. This patch fixes the CORE SEL slice configuration and switch ARM clock to ARM PLL. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8mq: Enable eMMC HS400 and SD UHS mode on EVKYe Li
iMX8MQ EVK board has a eMMC5.0 chip and supports SD3.0, so enable the UHS and HS400 configs to enhance the eMMC/SD access. The change also needs to set usdhc clock to 400Mhz, and add the off-on-delay-us to SD reset pin, otherwise some SD cards will fail to select UHS mode in re-initialization. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8m: update clock root and fix core_selPeng Fan
Update clock root table to let it be easy to configure clock at very early stage. Also the core_sel mux parent should be A53 CLK root and ARM PLL. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8m: acquire ATF commit hashPeng Fan
Acquire ATF commit hash when booting U-Boot to make user easy to know the ATF version. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8: move SIP macro to common headerPeng Fan
Move the SIP macro to common header and unify the name to make others could reuse them. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx: imx8m: add i.MX8MN variants supportPeng Fan
Add i.MX8MN variants support Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx: imx8m: add i.MX8MQ Dual and QuadLite supportPeng Fan
Add i.MX8MQ Dual and QuadLite variants. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx: cpu: support speed grade for i.MX8MPPeng Fan
i.MX8MP speed grade use same layout as i.MX8MN, so reuse it for i.MX8MP Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01imx8mn: Update speed gradePeng Fan
imx8mn speed grade fuse uses new definitions as below. So have to update get_cpu_speed_grade_hz function to match it. SPEED_GRADE[5:4] SPEED_GRADE[3:0] MHz xx 0000 2300 xx 0001 2200 xx 0010 2100 xx 0011 2000 xx 0100 1900 xx 0101 1800 xx 0110 1700 xx 0111 1600 xx 1000 1500 xx 1001 1400 xx 1010 1300 xx 1011 1200 xx 1100 1100 xx 1101 1000 xx 1110 900 xx 1111 800 Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-05-01imx8mm: Update CPU speed gradingYe Li
According to iMX8MM datasheet (IMX8MMIEC_Rev_D and IMX8MMCEC_Rev_D), the speed grading for imx8mm is 800Mhz, 1.2Ghz, 1.6Ghz and 1.8Ghz. Update them to get_cpu_speed_grade_hz function. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-05-01ARM: imx: imx8mm: Add missing clock entries for FEC clockMarek Vasut
All the FEC ethernet clock entries for iMX8MM are missing, while they are already present on iMX8MQ. Fill in the nodes on iMX8MM, as the FEC ethernet gets bogus clock information otherwise which makes ethernet inoperable. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-04-22spl: mmc: Rename spl_boot_mode() to spl_mmc_boot_mode()Harald Seiler
The function's name is misleading as one might think it is used generally to select the boot-mode when in reality it is only used by the MMC driver to find out in what way it should try reading U-Boot Proper from a device (either using a filesystem, a raw sector/partition, or an eMMC boot partition). Rename it to spl_mmc_boot_mode() to make it more obvious what this function is about. Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-04-20Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-imxTom Rini
2020-04-18Add support for i.MXRT1020-EVK boardGiulio Benetti
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-04-18Add i.MXRT1020 supportGiulio Benetti
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-04-17arch: arm: tqma6: apply default Kconfig for device modelMichael Krummsdorf
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
2020-04-17arm: imx6: configure NoC on i.MX6DQPBernhard Messerklinger
The i.MX6DP and i.MX6QP incorporate NoC interconnect logic which needs to be configured in order to use external DDR memory. This patch enables the SPL to configure the necessary registers in accordance with the NXP engineering bulletin EB828. Co-developed-by: Filip Brozović <fbrozovic@gmail.com> Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
2020-04-17mx7ulp: Only enable LDO if it is not already enabledFabio Estevam
LDO mode may be already enabled by the ROM and enabling it again can cause U-Boot to hang. Avoid this problem by only enabling LDO mode if it is initially disabled. Reported-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-04-17mx7ulp: Remove duplicated definitionsFabio Estevam
These PMC0 definitions are already defined in the beginning of the file, so remove the duplication. Reported-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-04-16arm: imx: update reference to README.mxc_habPatrick Delaunay
Update reference in files detected by scripts/documentation-file-ref-check doc/README.mxc_hab => doc/imx/habv4/* Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-04-13Merge branch 'next'Tom Rini
Pull in changes that have been pending in our 'next' branch. This includes: - A large number of CI improvements including moving to gcc-9.2 for all platforms. - amlogic, xilinx, stm32, TI SoC updates - USB and i2c subsystem updtaes - Re-sync Kbuild/etc logic with v4.19 of the Linux kernel. - RSA key handling improvements
2020-04-09imx: Fix imx8m FIT script issueYe Li
The FIT config node has reversed ATF and u-boot: ATF is set to 'firmware' but u-boot is set to 'loadables'. This script can work previously because spl fit driver wrongly appends fdt to all loadable images. With the issue fixed in commit 9d15d1d1c24f ("Revert "common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled"") the u-boot in 'loadables' does not have fdt appended and fails to work. So correct the script by moving u-boot to 'firmware' and ATF to 'loadables'. Signed-off-by: Ye Li <ye.li@nxp.com> Reported-by: Matt Porter <mporter@konsulko.com> Tested-by: Matt Porter <mporter@konsulko.com>
2020-03-17Merge tag 'ti-v2020.07-next' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-ti into next K3 J721E: * OSPI boot support * Support for loading remote cores in R5 SPL * PMIC ESM Support * Minor fixes for R5F and C7x remoteproc drivers K3 AM654: * Update AVS class 0 voltages. * Add I2C nodes DRA7xx/AM57xx: * Fixed Android boot on AM57xx AM33/AM43/Davinci: * switch to driver model for the net and mdio driver for baltos * Add DM/DTS support for omap video driver * Enable fastboot on am335x-evm
2020-03-10Merge tag 'mmc-2020-3-9' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
- DM support for CAxxxx SoCs - eMMC board for presidio-asic - Add defer probe for mmc sdhci - TI SoCs mmc misc update
2020-03-09imx8mm/mn: Add missing root clock entry for ARM core clockFrieder Schrempf
The current implementation in arch/arm/mach-imx/cpu.c uses non-DM code to retrieve the core clock frequency. As the root clock is not listed we currently get: CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Fix this by adding the missing entry, which results in: CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-09imx: Makefile: added missing ahab.oOliver Graute
added missing ahab.o in Makefile Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-09spl: mmc: Fix spl_mmc_get_uboot_raw_sector() implementationFaiz Abbas
The call to spl_mmc_get_uboot_raw_sector() completely ignores and overwrites the raw_sect value passed from the caller of spl_mmc_load(). Fix this by passing raw_sect to the function and returning the same value in the default case. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-03-03lib: elf: Move the generic elf loading/validating functions to libKeerthy
Move the generic elf loading/validating functions to lib/ so that they can be re-used and accessed by code existing outside cmd. While at it remove the duplicate static version of load_elf_image_phdr under arch/arm/mach-imx/imx_bootaux.c. Signed-off-by: Keerthy <j-keerthy@ti.com> Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-02-11Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dmTom Rini
sandbox conversion to SDL2 TPM TEE driver Various minor sandbox video enhancements New driver model core utility functions
2020-02-09ARM: imx: novena: Enable DM ethernetMarek Vasut
Convert to DM ethernet to prevent board removal. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org>
2020-02-09ARM: imx: novena: Move defconfig bits to arch KconfigMarek Vasut
Just move the defconfig entries which are required into the Novena entry in arch Kconfig, no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org>
2020-02-09board: toradex: Add Verdin iMX8M Mini supportIgor Opaniuk
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-05dm: core: Create a new header file for 'compat' featuresSimon Glass
At present dm/device.h includes the linux-compatible features. This requires including linux/compat.h which in turn includes a lot of headers. One of these is malloc.h which we thus end up including in every file in U-Boot. Apart from the inefficiency of this, it is problematic for sandbox which needs to use the system malloc() in some files. Move the compatibility features into a separate header file. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-02-05dm: core: Require users of devres to include the headerSimon Glass
At present devres.h is included in all files that include dm.h but few make use of it. Also this pulls in linux/compat which adds several more headers. Drop the automatic inclusion and require files to include devres themselves. This provides a good indication of which files use devres. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2020-01-26clock_imx8mq: Make frac_pll_init() staticPedro Jardim
Since frac_pll_init() is only used in this file, change it to 'static'. This fixes the following sparse warning: arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous prototype for ‘frac_pll_init’ [-Wmissing-prototypes] Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-26clock_imx8mq: Remove the function sscg_pll_init()Pedro Jardim
Function sscg_pll_init() is not used anywhere, so it can simply be deleted. This was found because of the following sparse warning: arch/arm/mach-imx/imx8m/clock_imx8mq.c:702:5: warning: no previous prototype for ‘sscg_pll_init’ [-Wmissing-prototypes] int sscg_pll_init(u32 pll) ^~~~~~~~~~~~~ Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-26clock_imx8mq: Make do_imx8m_showclocks() staticPedro Jardim
Since do_imx8m_showclocks() is only used inside this file, make it 'static'. This fixes the following sparse warning: arch/arm/mach-imx/imx8m/clock_imx8mq.c:836:5: warning: no previous prototype for ‘do_imx8m_showclocks’ [-Wmissing-prototypes] int do_imx8m_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, ^~~~~~~~~~~~~~~~~~~ Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-26clock_imx8mq: Delete not used init_usb_clk()Pedro Jardim
Function init_usb_clk() is not used anywhere, so it can simply be deleted. This was detected by the following sparse warning: arch/arm/mach-imx/imx8m/clock_imx8mq.c:377:6: warning: no previous prototype for ‘init_usb_clk’ [-Wmissing-prototypes] void init_usb_clk(void) ^~~~~~~~~~~~ Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
2020-01-21Merge tag 'u-boot-imx-20200121' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx --------------------------------- imx8: cleanup, fix warnings imx6ull: add VisionSOM SoM and EVK mx7ulp: fix warning due network, cleanup mx7dsabre: Fix dm probe pmic imx6: fixed for vining2000 Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/639512296
2020-01-20imx8m: clock_imx8mm: Staticize functionsAlifer Moraes
Functions fracpll_configure(), decode_intpll(), decode_fracpll(), get_root_src_clk() and get_root_clk() are used only in the scope of this file, so make them static to fix the following sparse warnings: arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous prototype for ‘fracpll_configure’ [-Wmissing-prototypes] arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous prototype for ‘decode_intpll’ [-Wmissing-prototypes] arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous prototype for ‘decode_fracpll’ [-Wmissing-prototypes] arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous prototype for ‘get_root_src_clk’ [-Wmissing-prototypes] arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous prototype for ‘get_root_clk’ [-Wmissing-prototypes] Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-12 15:38:18 +0000