summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2011-10-27tegra2: Add more pinmux functionsSimon Glass
This adds support for changing pinmux functions of pin groups. This is done by defining a PMUX_FUNC_... enum which can be used to select the function for each group using pinmux_set_func(). It is also possible to enable pullup/pulldown, and the existing tristate functionality is retained. Also provided is a means of configuring a list of pingroups by providing a configuration table to pinmux_config_table(). Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Warren <twarren@nvidia.com>
2011-10-27tegra2: Rename PIN_ to PINGRP_Simon Glass
The pin groupings are better named PINGRP, since on Tegra2 they refer to multiple pins. Sorry about this, but better to get it right now when there is only a small amount of code affected. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Warren <twarren@nvidia.com>
2011-10-27tegra2: Add more clock functionsSimon Glass
This adds most of the clock functions required by board and driver code: -query and adjust peripheral clocks -query and adjust PLLs -reset and enable control These functions are plumbed in as required. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Warren <twarren@nvidia.com>
2011-10-27tegra2: Rename CLOCK_PLL_ID to CLOCK_IDSimon Glass
Rename CLOCK_PLL_ID to CLOCK_ID which takes account of the fact that the code now deals with both PLL clocks and source clocks. This also tidied up the assert() to match the one sent upstream, and fixes an error in the PWM id. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Tom Warren <twarren@nvidia.com>
2011-10-26fdt: ARM: Add fdtcontroladdr to set device tree address in environmentSimon Glass
This adds support for a new environment variable called 'fdtcontroladdr'. If defined, the hex address is used as the address of the control fdt for U-Boot. Note: I have not changed CONFIG_PRAM section as I already have an outstanding patch on that. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26fdt: ARM: Implement and verify embedded and separate device treeSimon Glass
This locates the device tree either embedded within U-Boot or attached to the end as a separate binary. When CONFIG_OF_CONTROL is defined, U-Boot requires a valid fdt. A check is provided for this early in initialisation. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26fdt: ARM: Add device tree control of U-Boot (CONFIG_OF_CONTROL)Simon Glass
This adds a device tree pointer to the global data. It can be set by board code. A later commit will add support for making a device tree binary blob available to U-Boot for run-time configuration. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-24arm: Correct build error introduced by getenv_ulong() patchSimon Glass
Commit dc8bbea removed a local variable that is used in most ARM boards. Since we want to avoid an 'unused variable' warning with later compilers, and the #ifdef logic of whether this variable is required is bit painful, this declares the variable local to the block of code that needs it. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-23arm: Use getenv_ulong() in place of getenv(), strtoulSimon Glass
This changes the board code to use the new getenv_ulong() function. Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-23arm: cache: define ARCH_DMA_MINALIGN for DMA buffer alignmentAnton Staaf
Signed-off-by: Anton Staaf <robotboy@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-22build: add missing $(AR)->$(cmd_link_o_target) updateMike Frysinger
Seems people fixed their files to use libfoo.o, but didn't actually update the creation targets to use $(cmd_link_o_target). Update the rest of the Makefile's found with grep. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Simon Glass <sjg@chromium.org>
2011-10-22consolidate mdelay by providing a common function for all usersAnatolij Gustschin
There are several mdelay() definitions in the driver and board code. Remove them all and provide a common mdelay() in lib/time.c. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-17Move timestamp and version files into 'generated' subdirSimon Glass
There is a rather subtle build problem where the build time stamp is not updated for out-of-tree builds if there exists an in-tree build which has a valid timestamp file. So if you do an in-tree build, then an out-of-tree build your timestamp will not change. The correct timestamp_autogenerated.h lives in the object tree, but it is not always found there. The source still lives in the source tree and when compiling version.h, it includes timestamp_autogenerated.h. Since the current directory is always searched first, this will come from the source tree rather than the object tree if it exists there. This affects dependency generation also, which means that common/cmd_version.o will not even be rebuilt if you have ever done an in-tree build. A similar problem exists with the version file. This change moves both files into the 'generated' subdir, which is already used for asm-offsets.h. Then timestamp.h and version.h are updated to include the files from there. There are other places where these generated files are included, but I cannot see why these don't just use the timestamp.h and version.h headers. So this change also tidies that up. I have tested this with in- and out-of-tree builds, but not SPL. I have looked at various other options for fixing this, including sed on the dep files, -I- and -include flags to gcc, but I don't think they can be made to work. Comments welcome. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-17mx31: make HSP clock for mx3fb driver availableHelmut Raiger
This additionally updates mx31/generic.c by - replacing __REG() macro accesses with readl() and writel() - providing macros for PDR0 and PLL bit accesses Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-10-15punt unused clean/distclean targetsMike Frysinger
The top level Makefile does not do any recursion into subdirs when cleaning, so these clean/distclean targets in random arch/board dirs never get used. Punt them all. MAKEALL didn't report any errors related to this that I could see. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-09arm920t/s3c24x0/usb_ohci.c: fix warning: variable ... set but not usedWolfgang Denk
Fix: usb_ohci.c: In function 'dl_transfer_length': usb_ohci.c:768:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Remy Bohmer <linux@bohmer.net>
2011-10-09arch/arm/lib/board.c: fix warning: variable ... set but not usedWolfgang Denk
Fix: board.c:445:8: warning: variable 'bd' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-05board configs: drop NET_MULTI referencesMike Frysinger
Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05net: drop !NET_MULTI codeMike Frysinger
This is long over due. All but two net drivers have been converted, but those have now been dropped. The only thing left to do is actually delete all references to NET_MULTI and code that is compiled when that is not defined. So here we scrub the core code. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05image: push default arch values to arch headersMike Frysinger
This pushes the ugly duplicated arch ifdef lists we maintain in various image related files out to the arch headers themselves. Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Tested-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05POST: add post_log_res field for post results in global dataValentin Longchamp
The current post_log_word in global data is currently split into 2x 16 bits: half for the test start, half for the test success. Since we alredy have more than 16 POST tests defined and more could be defined, this may result in an overflow and the post_output_backlog would not work for the tests defined further of these 16 positions. An additional field is added to global data so that we can now support up to 32 (depending of architecture) tests. The post_log_word is only used to record the start of the test and the new field post_log_res for the test success (or failure). The post_output_backlog is for this change also adapted. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-10-05POST/arm: adaptations needed for POST on ARM to workValentin Longchamp
For post to run on ARM, 3 things are needed: - post_log_word to be defined in gd - a post.h include in arch/arm/lib/board.c Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05console: Implement pre-console bufferGraeme Russ
Allow redirection of console output prior to console initialisation to a temporary buffer. To enable this functionality, the board (or arch) must define: - CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer - CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer - CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes) The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes Any earlier characters are silently dropped.
2011-09-30zmx25: Fix build warning due to 'get_reset_cause' defined but not usedFabio Estevam
When building the zmx25 target we get: Configuring for zmx25 board... generic.c:108: warning: 'get_reset_cause' defined but not used Fix this warning by defining get_reset_cause only if CONFIG_DISPLAY_CPUINFO is defined. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2011-09-30MX5: Clean up the output of "clocks" commandMarek Vasut
The new output looks like this: > clocks PLL1 800 MHz PLL2 665 MHz PLL3 216 MHz AHB 133000 kHz IPG 66500 kHz IPG PERCLK 665000 kHz Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
2011-09-30MX5: Add AHB clock reporting and fix IPG clock reportingMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
2011-09-30MX5: Modify the PLL decoding algorithmMarek Vasut
The PLL decoding algorithm didn't take into account many configuration bits. Adjust it according to Linux kernel. Also, add PLL4 for MX53. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Hui <jason.hui@linaro.org> Tested-by: Jason Liu <Jason.hui@linaro.org>
2011-09-30FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.hMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30MX31: Disable watchdog during low-power modesFabio Estevam
Turn on the watchdog WDZST bit so that watchdog timer does not count during low power modes. Prior to applying this patch mx31pdk board got watchdog resets because when it booted in the Linux prompt and there was no activity, the system entered into idle mode while watchdog timer was still active. Fix this by disabling watchdog timer during idle mode. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-09-30MX25: tx25: Avoid the usage of extern in C fileFabio Estevam
Avoid the usage of extern in C file as pointed out by checkpatch. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-09-30MX31: Improve readability for reset causeFabio Estevam
Currently the reset cause is printed like: CPU: Freescale i.MX31 rev 2.0 at 531 MHz.Reset cause: POR Improve readability by adding a new line like it is done on other i.MX boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-09-30ARM: mx25: Print the source of resetFabio Estevam
Print the source of reset during boot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-09-30ARM: mx25: Print the silicon revisonFabio Estevam
Print the silicon revison during boot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-09-30arm, davinci, da8xx: add cpuinfoHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci, am1808: add lowlevel functions for booting from NORHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add NOR Boot Configuration WordHeiko Schocher
to add the "NOR Boot Configuration Word" on AM18xx based boards, define CONFIG_SYS_DV_NOR_BOOT_CFG. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add ddr2 definitionHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci, am1808, gpio: add missing defines for bank 8Heiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add some missing defines in hardware.hHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add SYSCFG1 base and register structHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add RTC base addrHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add internal WDT support for AM1808 cpusHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: add missing timer baseaddresses for !DA8xx cpuHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30arm, davinci: move davinci_timer in header fileHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30net, davinci_emac: add KSZ8864 switchHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30omap3: Fix compile warningSanjeev Premi
Building without option CONFIG_DISPLAY_CPUINFO leads to this warning: sys_info.c:50:14: warning: 'rev_s_37xx' defined but not used Signed-off-by: Sanjeev Premi <premi@ti.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30mmc: omap: config VMMC, MMC1_PBIASBalaji T K
Config VMMC voltage to 3V for MMC/SD card slot and PBIAS settings needed for OMAP4 Fixes MMC/SD detection on boot from eMMC. Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30devkit8000: Fix build breakSandeep Paulraj
Found a build erros when i ran MAKEALL. So fix it. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30omap-common: reorganize spl.cSimon Schwarz
split-up spl.c into spl.c, spl_mmc.c and spl_nand.c. This avoids problems with missing defines if a board does not use mmc or nand. This includes adding spl_ prefix to some functions which are now public. spl_image_t is now a public type. Added some of the common functions to omap-common.h Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30omap3: implement boot parameter savingSimon Schwarz
Implements the saving of boot params passed by OMAP3 ROM code. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit (git 2.34.1) at 2024-12-29 15:07:26 +0000