summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2020-02-13ARM: dts: stm32mp1: move FDCAN to PLL4_RAntonio Borneo
LTDC modifies the clock frequency to adapt it to the display. Such frequency change is not detected by the FDCAN driver that instead cache the value at probe and pretend to use it later. Keep the LTDC alone on PLL4_Q by moving the FDCAN to PLL4_R. Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13ARM: dts: stm32mp1: DT alignment with kernel v5.5-rc7Patrick Delaunay
Device tree and binding alignment with kernel v5.5-rc7 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13stm32mp1: pwr: use the last binding for pwrPatrick Delaunay
Update the driver to use the latest binding from kernel v5.5-rc1: no more use syscon or regmap to access to pwr register and only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg" is available. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13ARM: dts: stm32mp1: DT alignment with kernel v5.4Patrick Delaunay
Device tree and binding alignment with kernel v5.4 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13armV7R: K3: am654: Activate early console functionalityAndreas Dannenberg
Activate early console functionality on AM65x devices to allow for early diagnostic messages until the main console is ready to get activated. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-13arm: K3: j721e: Fix boot parameter table index memory addressAndreas Dannenberg
The boot parameter table index memory address for J721E was configured to an incorrect value which prevented the use of this definition to determine which boot parameter table is active which is needed to be able to distinguish between primary and backup boot modes. Fix this issue by updating the value to the correct one also in alignment with the J721E Technical Reference Manual (TRM). Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-13arm: mach-k3: Fix nomenclature on Silicon RevisionsLokesh Vutla
Data manual mentions the new silicon revisions as SR instead of PG. Use the same nomenclature inside U-Boot as well. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-13arm: dts: k3-j721e-r5-common-proc-board: Disable power-domains for mcu uartLokesh Vutla
mcu uart will be used during uart boot for loading sysfw.itb. Since sysfw is not yet available during uart load, power-domain cannot be enabled. We need to rely on ROM for doing that, so disable power-domains and clocks for mcu uart. Also fix the mcu uart frequency. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-13arm: dts: am437x-gp-evm: Add some nodes to u-boot.dtsiFaiz Abbas
Add scm_conf syscon node and its parents as well as the ethernet phy node to u-boot.dtsi. This enables ethernet boot. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-12ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 boardMarek Vasut
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board. This is an SoM with STM32MP15xx and an evaluation kit. The baseboard provides Ethernet, UART, USB, CAN and optional display. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-02-11Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dmTom Rini
sandbox conversion to SDL2 TPM TEE driver Various minor sandbox video enhancements New driver model core utility functions
2020-02-09board: ge: bx50v3: override panelIan Ray
Override the panel compatible string for LCD in U-Boot. Include U-Boot device tree overrides in device-specific device trees so that the panel compatible string is used. Fixes: 8c26739859c6 ("board: ge: bx50v3: sync devicetrees from Linux") Signed-off-by: Ian Ray <ian.ray@ge.com>
2020-02-09board: ge: mx53ppd: enable DM_VIDEOIan Ray
Enable DM_VIDEO for mx53ppd. Enable DM_REGULATOR_FIXED and DM_PWM for the backlight. Remove unused MX53PPD_LCD_POWER. Remove old (incorrect) setup_iomux_lcd. Enable backlight via display enable handler. Use cls command to initiate display in HW agnostic manner. Modify `failbootcmd' to use lcdputs. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09board: ge: mx53ppd: add i2c eeprom bootcount storageRobert Beckett
Add bootcount node, linking to i2c eeprom "bootcount" partitions for storage. Enable i2c eeprom bootcount backend storage. Enable bootcount command and use it for failbootcmd. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09board: ge: bx50v3: add i2c eeprom bootcount storageRobert Beckett
Add bootcount node, linking to i2c eeprom "bootcount" partitions for storage. Enable i2c eeprom bootcount backend storage. Enable bootcount command and use it for failbootcmd. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09board: ge: bx50v3, imx53ppd: use DM I2CRobert Beckett
Remove old (pre-DM) i2c setup code. Enable DM i2c. Convert common code to use DM rtc. Convert common code to read VPD from eeprom partition. Convert the generic i2c PMIC init code to use the new da9063 driver. mx53ppd only: Correct RTC compatible in device tree. Enable MXC DM i2c driver. Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc. Make GPIO banks available during preloc, since initialisation is done in board_early_init_f(). Add gpio_request() calls to satisfy the DM_GPIO compatibility API. Remove unused power configuration. Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Signed-off-by: Ian Ray <ian.ray@ge.com>
2020-02-09board: ge: bx50v3, imx53ppd: add eeprom partitionsRobert Beckett
Add eeprom partitions to device tree. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-02-09ARM: imx: novena: Enable DM ethernetMarek Vasut
Convert to DM ethernet to prevent board removal. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org>
2020-02-09ARM: imx: novena: Move defconfig bits to arch KconfigMarek Vasut
Just move the defconfig entries which are required into the Novena entry in arch Kconfig, no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org>
2020-02-09mx7dsabre: Fix usbtog probe when use dfu or umsJoris Offouga
Before: => ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00 usb dr_mode not found CTRL+C - Operation aborted => dfu 0 mmc 0 usb dr_mode not found After : => ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00 => dfu 0 mmc 0 Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-02-09arm: dts: imx7s-warp7: Move u-boot specific node in u-boot.dtsiJoris Offouga
These nodes are not in upstream kernel, so move these in u-boot.dtsi Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-02-09arm: xea: dts: Add 'fec-3v3' regulator properties to prevent accidental ↵Lukasz Majewski
disablement The 'enable-active-high' DTS property configures GPIO so it is active with HIGH state (by default it is low). The 'regulator-boot-on' property indicates that the regulator was enabled in the 'earlier' stage - i.e. bootloader/firmware. In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in very early SPL code, so it shouldn't be modified at latter stages. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-02-09board: toradex: Add Verdin iMX8M Mini supportIgor Opaniuk
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-09arm: dts: imx8mm-pinfunc: sync latest linux-next pin func headerMarcel Ziswiler
Synchronise with latest linux-next kernel pin func header file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-07board: presidio-asic: Add basic G3 engr. development board supportAlex Nemirovsky
Add basic Presidio G3 engineering board support Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07gpio: do not include <asm/arch/gpio.h> for Cortina CAxxxx SoCsJason Li
The Cortina CAxxxx GPIO driver maintains DM_GPIO support across different CPU ISA in the CAxxxx Soc Family; Not just ARM. Therefore, it is not desirable to split out and maintain separete gpio header file for each CPU architecture. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Jason Li <jason.li@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07arm: dts: mediatek: add ethernet and sgmii dts node for mt7622MarkLee
This patch add eth and sgmii dts node for mt7622 to support ethernet Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
2020-02-06Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- Gen 5 and Watchdog fixes
2020-02-05dm: core: Create a new header file for 'compat' featuresSimon Glass
At present dm/device.h includes the linux-compatible features. This requires including linux/compat.h which in turn includes a lot of headers. One of these is malloc.h which we thus end up including in every file in U-Boot. Apart from the inefficiency of this, it is problematic for sandbox which needs to use the system malloc() in some files. Move the compatibility features into a separate header file. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-02-05dm: core: Require users of devres to include the headerSimon Glass
At present devres.h is included in all files that include dm.h but few make use of it. Also this pulls in linux/compat which adds several more headers. Drop the automatic inclusion and require files to include devres themselves. This provides a good indication of which files use devres. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2020-02-05Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes on ls1012a, ls1021a, ls1028ardb platforms Integrate fspi for ls1028a, add DM-I2C support, update secure boot header offset
2020-02-05Merge tag 'rpi-next-2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi - DFU support file operations lager then the default max size - add dfu support to dwc2 for bcm2835 - enable DFU for RPi4 - Fix RPi4 memory map to include the genet device - add driver for the genet ethernet device - enable network support in RPi4 config
2020-02-05ddr: altera: Add DDR2 support to Gen5 driverMarek Vasut
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated by Quartus are named differently than the DDR3 ones, use anon unions to store them in the same structures, without growing their size. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-02-05watchdog: designware: Convert to DM and DT probingMarek Vasut
Convert the designware watchdog timer driver to DM and add DT probing support. Perform minor coding style clean up, like drop superfluous braces. These ought to be no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
2020-02-04dm: arm64: ls1012a: add i2c DM supportBiwen Li
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1012A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04armv8: fsl-layerscape: spl: fix build error when DM_I2C is enabledBiwen Li
Fix below SPL build error when DM_I2C is enabled, - arch/arm/cpu/armv8/built-in.o: In function `board_init_f: arch/arm/cpu/armv8/fsl-layerscape/spl.c:74: undefined reference to `i2c_init_all' arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:(.text.board_init_f+0x30): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `i2c_init_all' make[2]: *** [spl/u-boot-spl] Error 1 make[1]: *** [spl/u-boot-spl] Error 2 make: *** [sub-make] Error 2 arch/arm/cpu/armv8/fsl-layerscape/spl.c: In function 'board_init_f': arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:2: warning: implicit declaration of function 'i2c_init_all'; did you mean 'misc_init_r'? [-Wimplicit-function-declaration]` Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: lx2160a: Add FSPI node propertiesKuldeep Singh
Align flexspi node properties with linux device-tree properties Tested on LX2160A-RDB Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: ls1028a: Add FSPI node propertiesKuldeep Singh
Align flexspi node properties with linux device-tree properties Tested on LS1028A-RDB Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: ls1028a: fix interrupt propertiesMichael Walle
Sync the interrupt properties with the ones from Linux. Also use the constants provided by the dt-bindings header. Please note, that there are actual changes/fixes in the irq flags. U-Boot won't use the interrupt properties anyway. It's just to be consistent with the Linux device tree. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: ls1028a: use the new flexspi driverMichael Walle
Also align the fspi node with the kernel one. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: k3-j721e-main: Add Support for gpio0Faiz Abbas
Add the main_gpio0 node. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Enable I2C expander for SPLVignesh Raghavendra
IO expanders are required to power cycle SD card. So enable the same Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Add I2C GPIO expanderVignesh Raghavendra
Add I2C GPIO expander required to power cycle MMC/SD Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e: Add I2C nodesVignesh Raghavendra
J721e SoC has 2 I2C instances in MCU domain and 7 I2C instances in main domain. Add DT nodes for the same Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Enable USB0 in peripheral modeVignesh Raghavendra
Enable USB0 in peripheral mode so that it be used for DFU Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: mach-k3: sysfw-loader: Add support to download SYSFW via DFUVignesh Raghavendra
Add support to download SYSFW into internal RAM via DFU in DFU boot mode. Prepare a DFU config entity entry dynamically using buffer address allocated for SYSFW and start DFU gadget to get SYSFW. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: mach-k3: j721e: Rename BOOT_DEVICE_USB to BOOT_DEVICE_DFUVignesh Raghavendra
J721e does not support USB Host MSC boot, but only supports DFU boot. Since BOOT_DEVICE_USB is often used for host boot mode and BOOT_DEVICE_DFU is used for DFU boot, rename BOOT_DEVICE_USB macro to BOOT_DEVICE_DFU Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-03ARM: socfpga: Drop last use of socfpga_reset_managerMarek Vasut
This particular chunk of code was not updated, likely due to the order in which the patches were posted and applied. Fix this missing part. Fixes: bb25aca13433 ("arm: socfpga: Convert reset manager from struct to defines") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2020-02-01Merge tag 'u-boot-rockchip-20200130' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Support redundant boot for rk3399 - Support binman for rockchip platform - Update ram driver and add ddr4 support for rk3328
2020-01-31Merge tag 'uniphier-v2020.04-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier UniPhier SoC updates for v2020.04 (2nd) Denali NAND driver changes: - Set up more registers in denali-spl for SOCFPGA - Make clocks optional - Do not assert reset signals in the remove hook - associate SPARE_AREA_SKIP_BYTES with DT compatible - switch to UCLASS_MTD UniPhier platform changes: - fix a bug in dram_init() - specify loadaddr for "source" command
generated by cgit (git 2.34.1) at 2025-01-11 00:10:27 +0000