summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2020-02-09mx7dsabre: Fix usbtog probe when use dfu or umsJoris Offouga
Before: => ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00 usb dr_mode not found CTRL+C - Operation aborted => dfu 0 mmc 0 usb dr_mode not found After : => ums 0 mmc 0 UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x1dacc00 => dfu 0 mmc 0 Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-02-09arm: dts: imx7s-warp7: Move u-boot specific node in u-boot.dtsiJoris Offouga
These nodes are not in upstream kernel, so move these in u-boot.dtsi Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-02-09arm: xea: dts: Add 'fec-3v3' regulator properties to prevent accidental ↵Lukasz Majewski
disablement The 'enable-active-high' DTS property configures GPIO so it is active with HIGH state (by default it is low). The 'regulator-boot-on' property indicates that the regulator was enabled in the 'earlier' stage - i.e. bootloader/firmware. In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in very early SPL code, so it shouldn't be modified at latter stages. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-02-09board: toradex: Add Verdin iMX8M Mini supportIgor Opaniuk
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-09arm: dts: imx8mm-pinfunc: sync latest linux-next pin func headerMarcel Ziswiler
Synchronise with latest linux-next kernel pin func header file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-02-07board: presidio-asic: Add basic G3 engr. development board supportAlex Nemirovsky
Add basic Presidio G3 engineering board support Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07gpio: do not include <asm/arch/gpio.h> for Cortina CAxxxx SoCsJason Li
The Cortina CAxxxx GPIO driver maintains DM_GPIO support across different CPU ISA in the CAxxxx Soc Family; Not just ARM. Therefore, it is not desirable to split out and maintain separete gpio header file for each CPU architecture. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Jason Li <jason.li@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
2020-02-07arm: dts: mediatek: add ethernet and sgmii dts node for mt7622MarkLee
This patch add eth and sgmii dts node for mt7622 to support ethernet Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
2020-02-06Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- Gen 5 and Watchdog fixes
2020-02-05Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes on ls1012a, ls1021a, ls1028ardb platforms Integrate fspi for ls1028a, add DM-I2C support, update secure boot header offset
2020-02-05Merge tag 'rpi-next-2020.04' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi - DFU support file operations lager then the default max size - add dfu support to dwc2 for bcm2835 - enable DFU for RPi4 - Fix RPi4 memory map to include the genet device - add driver for the genet ethernet device - enable network support in RPi4 config
2020-02-05ddr: altera: Add DDR2 support to Gen5 driverMarek Vasut
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated by Quartus are named differently than the DDR3 ones, use anon unions to store them in the same structures, without growing their size. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-02-05watchdog: designware: Convert to DM and DT probingMarek Vasut
Convert the designware watchdog timer driver to DM and add DT probing support. Perform minor coding style clean up, like drop superfluous braces. These ought to be no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
2020-02-04dm: arm64: ls1012a: add i2c DM supportBiwen Li
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1012A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04armv8: fsl-layerscape: spl: fix build error when DM_I2C is enabledBiwen Li
Fix below SPL build error when DM_I2C is enabled, - arch/arm/cpu/armv8/built-in.o: In function `board_init_f: arch/arm/cpu/armv8/fsl-layerscape/spl.c:74: undefined reference to `i2c_init_all' arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:(.text.board_init_f+0x30): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `i2c_init_all' make[2]: *** [spl/u-boot-spl] Error 1 make[1]: *** [spl/u-boot-spl] Error 2 make: *** [sub-make] Error 2 arch/arm/cpu/armv8/fsl-layerscape/spl.c: In function 'board_init_f': arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:2: warning: implicit declaration of function 'i2c_init_all'; did you mean 'misc_init_r'? [-Wimplicit-function-declaration]` Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: lx2160a: Add FSPI node propertiesKuldeep Singh
Align flexspi node properties with linux device-tree properties Tested on LX2160A-RDB Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: ls1028a: Add FSPI node propertiesKuldeep Singh
Align flexspi node properties with linux device-tree properties Tested on LS1028A-RDB Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: ls1028a: fix interrupt propertiesMichael Walle
Sync the interrupt properties with the ones from Linux. Also use the constants provided by the dt-bindings header. Please note, that there are actual changes/fixes in the irq flags. U-Boot won't use the interrupt properties anyway. It's just to be consistent with the Linux device tree. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: ls1028a: use the new flexspi driverMichael Walle
Also align the fspi node with the kernel one. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04arm: dts: k3-j721e-main: Add Support for gpio0Faiz Abbas
Add the main_gpio0 node. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Enable I2C expander for SPLVignesh Raghavendra
IO expanders are required to power cycle SD card. So enable the same Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Add I2C GPIO expanderVignesh Raghavendra
Add I2C GPIO expander required to power cycle MMC/SD Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e: Add I2C nodesVignesh Raghavendra
J721e SoC has 2 I2C instances in MCU domain and 7 I2C instances in main domain. Add DT nodes for the same Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: dts: k3-j721e-common-proc-board: Enable USB0 in peripheral modeVignesh Raghavendra
Enable USB0 in peripheral mode so that it be used for DFU Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: mach-k3: sysfw-loader: Add support to download SYSFW via DFUVignesh Raghavendra
Add support to download SYSFW into internal RAM via DFU in DFU boot mode. Prepare a DFU config entity entry dynamically using buffer address allocated for SYSFW and start DFU gadget to get SYSFW. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-04arm: mach-k3: j721e: Rename BOOT_DEVICE_USB to BOOT_DEVICE_DFUVignesh Raghavendra
J721e does not support USB Host MSC boot, but only supports DFU boot. Since BOOT_DEVICE_USB is often used for host boot mode and BOOT_DEVICE_DFU is used for DFU boot, rename BOOT_DEVICE_USB macro to BOOT_DEVICE_DFU Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-02-03ARM: socfpga: Drop last use of socfpga_reset_managerMarek Vasut
This particular chunk of code was not updated, likely due to the order in which the patches were posted and applied. Fix this missing part. Fixes: bb25aca13433 ("arm: socfpga: Convert reset manager from struct to defines") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dalon Westergreen <dwesterg@gmail.com> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2020-02-01Merge tag 'u-boot-rockchip-20200130' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Support redundant boot for rk3399 - Support binman for rockchip platform - Update ram driver and add ddr4 support for rk3328
2020-01-31Merge tag 'uniphier-v2020.04-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier UniPhier SoC updates for v2020.04 (2nd) Denali NAND driver changes: - Set up more registers in denali-spl for SOCFPGA - Make clocks optional - Do not assert reset signals in the remove hook - associate SPARE_AREA_SKIP_BYTES with DT compatible - switch to UCLASS_MTD UniPhier platform changes: - fix a bug in dram_init() - specify loadaddr for "source" command
2020-02-01ARM: uniphier: set gd->ram_base correctlyMasahiro Yamada
gd->ram_base is not set at all if the end address of the DRAM ch0 exceeds the 4GB limit. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-01mtd: rawnand: denali_dt: use UCLASS_MTD instead of UCLASS_MISCMasahiro Yamada
UCLASS_MTD is a better fit for NAND drivers. Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile drivers/mtd/mtd-uclass.c Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig of this platform enables NAND_DENALI_DT. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
2020-02-01ARM: uniphier: remove adhoc reset deassertion for the NAND controllerMasahiro Yamada
Now that the reset controlling of the Denali NAND driver (denali_dt.c) works for this platform, remove the adhoc reset deassert code. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-30rockchip: rk3308: add alias for emmc/sdmmcKever Yang
Add alias for mmc/sdmmc so that we can have a fix mmc number for emmc. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30ram: rk3328: update lpddr3 settingYouMin Chen
update lpddr3 setting for fix init fail about "col error". Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30ram: rk3328: add support ddr4 initYouMin Chen
Add rk3328-sdram-ddr4-666.dtsi for support ddr4 init. Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30rockchip: Add Single boot image (with binman, pad_cat)Jagan Teki
All rockchip platforms support TPL or SPL-based bootloader in mainline with U-Boot proper as final stage. For each stage we need to burn the image on to flash with respective offsets. This patch creates a single boot image component using - binman, for arm32 rockchip platforms - pad_cat, for arm64 rockchip platforms. This would help users to get rid of burning different boot stage images. The new image called 'u-boot-rockchip.bin' which can burn into flash like: ₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64 This would support all rockchip platforms, except rk3128 since it doesn't support for SPL yet. Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com> Cc: Wadim Egorov <w.egorov@phytec.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30arm: dts: rk3188: Add rk3188-u-boot.dtsiJagan Teki
Add U-Boot specific dtsi file for rk3188 SoC. This would help to add U-Boot specific dts nodes, properties which are common across rk3188. Right now, the file is empty, will add required changes in future patches. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30arm: dts: rk3036: Add rk3036-u-boot.dtsiJagan Teki
Add U-Boot specific dtsi file for rk3036 SoC. This would help to add U-Boot specific dts nodes, properties which are common across rk3036. Right now, the file is empty, will add required changes in future patches. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30rockchip: rk3399: Add bootcount supportJagan Teki
Add bootcount support for Rockchip rk3399. The bootcount value is preserved in PMU_SYS_REG0 register, this would help to support redundent boot. Once the redundant boot triggers, the altboot command will look for extlinux-rollback.conf on particular bootable partition which supposed to be a recovery partition where redundant boot required. Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30rockchip: Add common reset causeJagan Teki
Add cpu reset cause in common cpu-info file. This would help to print the reset cause for various resets. Right now it support rk3288, rk3399. rest of rockchip platforms doesn't have reset cause support ye but this code is more feasible to extend the same. Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30arm: rockchip: Add common cru.hJagan Teki
Few of the rockchip family SoC atleast rk3288, rk3399 are sharing some cru register bits so adding common code between these SoC families would require to include both cru include files that indeed resulting function declarations error. So, create a common cru include as cru.h then include the rk3399 arch cru include file and move the common cru register bit definitions into it. The rest of rockchip cru files will add it in future. Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30rockchip: Add cpu-infoJagan Teki
Add cpu information for rockchip soc. This would help to print the SoC family number, with associated temparature, clock and reason for reset etc. Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-30rockpro-rk3399: Enable SPI FlashJagan Teki
Enable winbond SPI flash for ROC-PC-RK3399 board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30roc-pc-rk3399: Enable SPI FlashJagan Teki
Enable winbond SPI flash for ROC-PC-RK3399 board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-30rockchip: dts: Sync ROC-RK3399-PC changes from LinuxJagan Teki
Sync the ROC-RK3399-PC device tree changes from Linux with below commit details: commit <c36308abe4110e4db362d5e2ae3797834a7b1192> ("arm64: dts: rockchip: Enable MTD Flash on rk3399-roc-pc") Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-29rpi4: Update memory map to accommodate scb devicesAmit Singh Tomar
Some of the devices(for instance, pcie and gnet controller) sitting on SCB bus falls behind/below the memory range that we currenty have. This patch updates the memory range to map those devices correctly. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-01-28Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-samsungTom Rini
- Various exynos fixes
2020-01-28arm: exynos: Read default MMC device from XOM[7:5] pinsMarek Szyprowski
XOM pins provide information for iROM bootloader about the boot device. Those pins are mapped to lower bits of OP_MODE register (0x10000008), which is common for all Exynos SoC variants. Set the default MMC device id to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for the eMMC). Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2020-01-27Merge tag 'u-boot-clk-26Jan2020' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-clk - Various clock fixes and enhancements
2020-01-26clock_imx8mq: Make frac_pll_init() staticPedro Jardim
Since frac_pll_init() is only used in this file, change it to 'static'. This fixes the following sparse warning: arch/arm/mach-imx/imx8m/clock_imx8mq.c:662:5: warning: no previous prototype for ‘frac_pll_init’ [-Wmissing-prototypes] Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
generated by cgit (git 2.34.1) at 2024-12-26 01:23:45 +0000