summaryrefslogtreecommitdiff
path: root/arch/arm
AgeCommit message (Collapse)Author
2018-05-31arm64: zynqmp: Disable WP on zcu111Michal Simek
On this board there is SD slot without WP connected. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Remove broken-cd from zcu100-revCMichal Simek
Card detect bit was broken on revA and it is working fine with revC board that's why this property can be removed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Fix address for tca6416_u97 chip on zcu104Michal Simek
I2c address is not 0x21 but 0x20. This patch is fixing both revA and revC boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Add ina226 to zcu104 revCMichal Simek
Add new ina226 chip present on i2c bus which wasn't on revA. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm: zynq: Add support for Bitmain Antminer S9 control boardEzequiel Garcia
This is control board on Bitmain Antminer S9. There are 3 board variables with 256MB, 512MB and 1024MB DDR. DDR memory is automatically detected with using get_with using get_ram_size(). Bitmain is using 16MB space for FPGA which is handled via reserved-memory. Also U-Boot is allocating 16B for storing bootcounts. Watchdog is started but never service in U-Boot. SPL MMC is working. SPL NAND is not working because it is not supported as of now. Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm: zynq: Add initial support for Avnet MiniZedIbai Erkiaga
Initial support for Avnet MiniZed board. Tested UART1 (serial console), QSPI(Flash), SDHCI1 (eMMC), USB. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31soc: zynqmp: Update required API version to 1.0Rajan Vaja
Existing EEMI version is to as 1.0 (available from xilinx v2018.1 version). Update required API version to match with EEMI API version. New PMUFW version is required for operations with programmable logic. Signed-off-by: Rajan Vaja <rajanv@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Get rid of emulation platformsMichal Simek
ZynqMP emulation platforms are no longer tested and supported that's why remove macros and code around. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Show reset reasonMichal Simek
Read reset reason reg and show it in log and also save it as variable. Clearing reset reason when it is read to show only one status Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-26stm32mp1: use OTP to configure MAC address and serial numberPatrick Delaunay
Use OTP57 and 58 for MAC address - OTP57 = MAC address bits [31:0] - OTP58 = MAC address bit [47:32] stored in OTP LSB's Use manufacture information in OTP13 to OTP15 to build unique chip id saved in env variable "serial#" (used for USB device enumeration) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26stm32mp1: add FUSE command supportPatrick Delaunay
Add support of fuse command (read/write/program/sense) on bank 0 to access to BSEC SAFMEM (4096 OTP bits). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26stm32mp1: add bsec driverPatrick Delaunay
Add a MISC driver with read and write access to BSEC IP (Boot and Security and OTP control) - offset 0: shadowed values - offset 0x80000000: OTP fuse box values (SAFMEM) Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26stm32mp1: remove the second TAMP_BOOT_CONTEXT updatePatrick Delaunay
The register TAMP_BOOT_CONTEXT is already updated in get_bootmode() in cpu.c and no need to be done twice. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26stm32mp1: Allow to activate CONFIG_DEBUG_UARTPatrick Delaunay
Add the needed information to enable the debug uart to have printf before the serial driver probe (so before probe for clock, pincontrol and reset drivers) To enable the debug on uart 4 (default console): + CONFIG_DEBUG_UART=y + CONFIG_DEBUG_UART_STM32=y Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26ram: stm32_sdram: Adds stm32f429-disco fixes for HardFault at bootingRadoslaw Pietrzyk
- adds reading FMC swap setting from DTB to SDRAM driver - sets FMC swap for stm32f429-disco board - changes ram start address to 0x90000000 Signed-off-by: Radoslaw Pietrzyk <radoslaw.pietrzyk@gmail.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26db410: added pinctrl node and serial bindingsRamon Fried
Added TLMM pinctrl node for pin muxing & config. Additionally, added a serial node for uart. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-05-26mach-snapdragon: Introduce pinctrl driverRamon Fried
This patch adds pinmux and pinctrl driver for TLMM subsystem in snapdragon chipsets. Currently, supporting only 8016, but implementation is generic and 8096 can be added easily. Driver is using the generic dt-bindings and doesn't introduce any new bindings (yet). Signed-off-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-26mach-snapdragon: Fix UART clock flowRamon Fried
UART clock enabling flow was wrong. Changed the flow according to downstream implementation in LK. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-05-26db820c: set clk node to be probed before relocationRamon Fried
The clock and serial nodes are needed before relocation. This patch ensures that the msm-serial driver will probe and provide uart output before relocation. Signed-off-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-23arm: print instructions pointed to by pcHeinrich Schuchardt
If an exception occurs in a loaded image and the relocation offset is unknown, it is helful to know the instructions pointed to by the program counter. This patch adds the missing output. A possible output is: Code: e1c560d0 e12fff1e e120077b e12fff1e (e7f7defb) The parentheses indicate the instruction causing the exception. The output can be disassembled using the decodecode script provided by the Linux kernel project. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-05-23arm64: timer: Create timer_get_bootus for bootstage supportMichal Simek
Implement timer_get_boot_us() based on available functions to support bootstage command. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-23arm: armv7m: Clean up some thumb / compiler flag optionsTom Rini
- The correct way to build with thumb mode is to select SYS_THUMB_BUILD - We should be setting -march=armv7-m in arch/arm/Makefile not the sub-config.mk file. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-22at91: Minor tweaks to SPL logic for space savings on smartwebTom Rini
- spl_board_init is empty on smartweb so drop that function - When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in SPL and instead let full U-Boot handle it. Instead of an empty function just do not call a function. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-23ARM: dts: uniphier: sync with Linux 4.17-rc6Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: uniphier: rename environment variable fdt_file to fdtfileMasahiro Yamada
For booting Linux in the generic distro mechanism, cmd/pxe.c retrieves the FDT file name from "fdtfile" environment variable. Rename "fdt_file" to "fdtfile" for easier migration to distro boot. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: change phy-mode to 'internal' for LD11Kunihiko Hayashi
Change the phy-mode property to 'internal' that means to use a built-in PHY implemented on LD11 SoC. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: add clock-names and reset-names to ethernet nodeKunihiko Hayashi
Add clock-names and reset-names because this node recognizes multiple clocks and resets. ("ether", and so on, for each) Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: add required clocks and resets to Pro4 ethernet nodeKunihiko Hayashi
The GIO clock/reset, another MAC clock, and the PHY clock are required for the ethernet of Pro4 SoC. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23ARM: dts: uniphier: add syscon-phy-mode property to each ethernet nodeKunihiko Hayashi
Add syscon-phy-mode property specifying a phandle of system controller to each ethernet node. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-20SPDX: Fixup SPDX tags in a few new filesTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-20Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-05-20Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2018-05-20Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2018-05-20ARM: rmobile: Unify Gen2 Makefile entryMarek Vasut
Drop per-SoC Makefile entries and replace them with one unified entry now that the PFC tables are gone. Shuffle the Makefile around a bit to make it more organized. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-20ARM: rmobile: Drop old R8A7794 PFC tablesMarek Vasut
All the boards use new modern PFC framework, the old PFC tables are no longer used, so remove them. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-20ARM: rmobile: Drop old R8A7793 PFC tablesMarek Vasut
All the boards use new modern PFC framework, the old PFC tables are no longer used, so remove them. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-20ARM: rmobile: Drop old R8A7792 PFC tablesMarek Vasut
All the boards use new modern PFC framework, the old PFC tables are no longer used, so remove them. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-20ARM: rmobile: Drop old R8A7791 PFC tablesMarek Vasut
All the boards use new modern PFC framework, the old PFC tables are no longer used, so remove them. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-20ARM: rmobile: Drop old R8A7790 PFC tablesMarek Vasut
All the boards use new modern PFC framework, the old PFC tables are no longer used, so remove them. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-20ARM: rmobile: Update V2H BlancheMarek Vasut
The V2H Blanche port was broken since some time. This patch updates the V2H Blanche port to use modern frameworks, DM, DT probing, SPL for the preloading and puts it on par with the M2 Porter board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-18Fixup various SPDX tags from the latest mergeTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-18arm64: zynqmp: Use DWC3 generic driver and DM_USBMichal Simek
Remove harcoded XHCI lists and detect mode, speed based on DT. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Serial-changes: 2 - Remove also XHCI macros from hardware.h - Remove additional new line in zcu106
2018-05-18Merge git://git.denx.de/u-boot-imxTom Rini
2018-05-18arm: dts: socfpga: stratix10: update dtsi and dtsLey Foon Tan
Update dtsi and dts files for resets, phy node and other properties. Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18arm: socfpga: misc: Add CONFIG_SYS_L2_PL310 switchLey Foon Tan
Preparation for Stratix 10 enablement. In ARM64, L2 cache controller is accessed through processor registers. So, add CONFIG_SYS_L2_PL310 switch conditional build in order this file can by shared across other SOCFPGAs. Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18arm: socfpga: stratix10: Add pinmux support for Stratix10 SoCLey Foon Tan
Add pinmux driver support for Stratix SoC Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18arm: socfpga: stratix10: Add reset manager driver for Stratix10 SoCLey Foon Tan
Add Reset Manager driver support for Stratix SoC Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18arm: socfpga: stratix10: Add clock manager driver for Stratix10 SoCLey Foon Tan
Add Clock Manager driver support for Stratix SoC Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18arm: socfpga: stratix10: Add watchdog and firewall base addressesLey Foon Tan
Add the base address for watchdog and firewall. Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-05-18ARM: socfpga: Fix Documentation errors in scu_registersBen Kalo
According to ARM Cortex-A9 MPCore TRM section 2.2 - SCU registers Access Control register offset is 0x50. Signed-off-by: Ben Kalo <ben.h.kalo@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
generated by cgit (git 2.34.1) at 2024-12-27 07:39:48 +0000