summaryrefslogtreecommitdiff
path: root/arch/powerpc
AgeCommit message (Collapse)Author
2011-03-05powerpc/85xx: Fix plat_mp_up() disabling of BPTR for CoreNet PlatformsEd Swarthout
Copying directly from ECM/PQ3 is not correct for how CoreNet based platforms handle boot page translation. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-05powerpc/mpc8xxx: Fix DDR3 timing_cfg_1 and sdram_mode registersYork Sun
The write recovery time of both registers should match. Since mode register doesn't support cycles of 9,11,13,15, we should use next higher number for both registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-10powerpc/8xxx: Add additional cycle to write-to-read turnaound for DDR3York Sun
When DDR data rate is higher than 1200MT/s or controller interleaving is enabled, additional cycle for write-to-read turnaround is needed to satisfy dynamic ODT timing. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-09Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2011-02-07ppc4xx: Add DLVision-10G board supportDirk Eibach
Board support for the Guntermann & Drunck DLVision-10G. Adds support for multiple FPGAs per board for gdsys 405ep architecture. Adds support for dual link osd hardware for gdsys 405ep. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-02-06Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
2011-02-05mpc83xx: Use correct register to calculate clocks.Joakim Tjernlund
Use SPMR instead of HRCWL when calculating clocks as HCRWL may be changed and the CPU will not pick up all changes until there is a POR. u-boot will think SPMF has changed and get the clocks wrong. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-02-05mpc83xx: fix pcie configuration space read/writeLeo Liu
This patch fix a problem for the pcie enumeration when the mpc83xx pcie controller is connected with switch or we use both of the two pcie controller. Signed-off-by: Leo Liu <liucai.lfn@gmail.com> fix codingstyle and compiler warning: 'pcie_priv' defined but not used Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-02-04powerpc/8xxx: Fix possible compile issue related to P1013Kumar Gala
The P1013 is a single core version of P1022 and thus should use the p1022_serdes.c code. It was acciently pointing to p1013_serdes.c which doesn't exist. Reported-by: Renaud Barbier <renaud.barbier@ge.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03powerpc/mpc85xx: implement workaround for errata DDR111 and DDR134York Sun
Workaround for the following errata: DDR111 - MCKE signal may not function correctly at assertion of HRESET DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can calibrate to incorrect values These two workarounds must be implemented together because they touch common registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03powerpc/85xx: Rename MPC8572 DDR erratum to DDR115York Sun
Use unique erratum number instead of platform number. Enable command that reports errata on MPC8572DS. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03powerpc/85xx: Remove unnecessary polling loop from DDR initYork Sun
This polling loop is not required normally, unless specifically stated in workaround. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03fsl_esdhc: Add the workaround for erratum ESDHC-A001 (enable on P2020)Kumar Gala
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8, and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03powerpc/85xx: Enable ESDHC111 Erratum on P2010/P2020 SoCsKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-02Minor Coding Style Cleanup.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-01-25Divides variable of linker flags to LDFLAGS-u-boot and LDFLAGSNobuhiro Iwamatsu
Linker needs to use the proper endian/bfd flags even when doing partial linking. LDFLAGS_u-boot sets linker option which is called it when U-boot is built (u-boot final). LDFLAGS sets necessary option by partial linking (use in cmd_link_o_target). CC: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-01-25Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2011-01-24powerpc/8xxx: Fix compile warning when build for a DDR1 or DDR2 boardKumar Gala
ctrl_regs.c: In function 'set_ddr_sdram_mode_2': ctrl_regs.c:690:6: warning: unused variable 'i' 'i' is only used by DDR3 code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/85xx: Protect all LBC code with CONFIG_FSL_LBCDipen Dudhat
Future SoC (like the P1010) replace the LBC controller with the new IFC (Integrated Flash Controller) so ensure we properly protect code that is related to the LBC. Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/p4080: Fix warning in serdes code from early use of hwconfigYork Sun
Hwconfig is called before relocating. Use the new hwconfig APIs. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19corenet_ds: Extend board specific parametersYork Sun
Extend board specific parameters to include cpo, write leveling override Extend write leveling sample to 0xf Adding rcw overrid for quad-rank RDIMMs Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19mpc85xx: Implement workaround for erratum DDR-A003York Sun
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM. Also adding polling after enabling DDR controller to ensure completion. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19mpc85xx: Enable unique mode registers and dynamic ODT for DDR3York Sun
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version (major, minor, errata) to determine if unique mode registers are available. If true, always use unique mode registers. Dynamic ODT is enabled if needed. The table is documented in doc/README.fsl-ddr. This function may also need to be extend for future other platforms if such a feature exists. Enable address parity and RCW by default for RDIMMs. Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for quad-rank RDIMMs. Use a formula to calculate rodt_on for timing_cfg_5. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19mpc85xx: Adding more registers and optionsYork Sun
This patch exposes more registers which can be used by the DDR drivers or interactive debugging. U-boot doesn't use all the registers in DDRC. When advanced tuning is required, writing to those registers is needed. Add writing to cdr1, cdr2, err_disable, err_int_en and debug registers Add options to override rcw, address parity to RDIMMs. Use array for debug registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19mpc8xxx: Enable ECC on/off control in hwconfigYork Sun
Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file, ECC can be turned on/off by this switch. If this switch is omitted, it is ON by default. Updated hwconfig calls to use local buffer. Syntax is hwconfig=fsl_ddr:ecc=on Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19mpc8xxx: Display RDIMM if detectedYork Sun
Print a message when a RDIMM is detected. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/8xxx: Introduce 85xx, 86xx, QorIQ config headersKumar Gala
Add new headers that capture common defines for a given SoC/processor rather than duplicating that information in board config.h and random other places. Eventually this should be handled by Kconfig & defconfigs Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-19powerpc/8xxx: Add hwconfig APIs to address early parsing used by DDR initKumar Gala
There are several users of the hwconfig APIs (8xxx DDR) before we have the environment properly setup. This causes issues because of the numerous ways the environment might be accessed because of the non-volatile memory it might be stored in. Additionally the access might be so early that memory isn't even properly setup for us. Towards resolving these issues we provide versions of all the hwconfig APIs that can be passed in a buffer to parse and leave it to the caller to determine how to allocate and populate the buffer. We use the _f naming convention for these new APIs even though they are perfectly useable after relocation and the environment being ready. We also now warn if the non-f APIs are called before the environment is ready to allow users to address the issues. Finally, we convert the 8xxx DDR code to utilize the new APIs to hopefully address the issue once and for all. We have the 8xxx DDR code create a buffer on the stack and populate it via getenv_f(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-19powerpc/p2040: Add various p2040 specific informationKumar Gala
Add P2040 SoC specific information: * SERDES Table * Added p2040 to cpu_type_list and SVR list * Added number of LAWs for p2040 * Set CONFIG_MAX_CPUS to 4 for p2040 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/p5020: Add various p5020 specific informationKumar Gala
Add P5020 SoC specific information: * SERDES Table * LIODN setup * Portal configuration Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/p3041: Add various p3041 specific informationKumar Gala
Add P3041 SoC specific information: * SERDES Table * LIODN setup * Portal configuration Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/85xx: Add Support for Freescale P1014 ProcessorPoonam Aggrwal
The P1014 is similar to the P1010 processor with the following differences: - 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC) - no eCAN interface. (P1010 has 2 eCAN interfaces) - Two SGMII interface (P1010 has 3 SGMII) - No secure boot Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19powerpc/85xx: Add Support for Freescale P1010 ProcessorPoonam Aggrwal
Key Features include of the P1010: * e500v2 core frequency operation of 500 to 800 MHz * Power consumption less than 5.0 W at 800 MHz core speed * Dual SATA 3 Gbps controllers with integrated PHY * Dual PCI Express controllers * Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs) * TCP/IP acceleration and classification capabilities * IEEE 1588 support * Lossless flow control * RGMII, SGMII * DDR3 with support for a 32-bit data interface (40 bits including ECC), up to 800 MHz data rate 32/16-bit DDR3 memory controller * Dedicated security engine featuring trusted boot * TDM interface * Dual controller area networks (FlexCAN) controller * SD/MMC card controller supporting booting from Flash cards * USB 2.0 host and device controller with an on-chip, high-speed PHY * Integrated Flash controller (IFC) * Power Management Controller (PMC) * Four-channel, general-purpose DMA controller * I2C controller * Serial peripheral interface (SPI) controller with master and slave support * System timers including a periodic interrupt timer, real-time clock, software watchdog timer, and four general-purpose timers * Dual DUARTs Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19Fix wrong CONFIG_SYS_MPC85xx_SERDES1_ADDRPrabhakar
CONFIG_SYS_MPC85xx_SERDES1_ADDR was defined wrong as CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES2_OFFSET. It should be as CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES1_OFFSET. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2011-01-19powerpc/85xx: Move RESET_VECTOR_ADDRESS into config.hKumar Gala
Rather than defining it config.mk we can set it in config.h and remove config.mk from several boards that don't need it. We mimic what 4xx does and introduce CONFIG_RESET_VECTOR_ADDRESS for config.h to set. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-198xxx/ddr: add support to only compute the ddr sdram sizeHaiying Wang
This patch adds fsl_ddr_sdram_size to only calculate the ddr sdram size, in case that the DDR SDRAM is initialized in the 2nd stage uboot and should not be intialized again in the final stage uboot. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19Replace "FLASH" strings with "Flash" or "flash"Peter Tyser
There's no compelling reason to have the output on bootup or the "flinfo" command print "flash" in uppercase, so use the proper case where appropriate. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2011-01-14powerpc/85xx: Add the workaround for erratum ELBC-A001 (enable on P4080)Kumar Gala
Simultaneous FCM and GPCM or UPM operation may erroneously trigger bus monitor timeout. Set timeout to maximum to avoid. Based on a patch from Lan Chunhe <b25806@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14powerpc/85xx: Add the workaround for erratum CPC-A003 (enable on P4080)Kumar Gala
CoreNet Platform Cache single-bit data error scrubbing will cause data corruption. Disable the feature to workaround the issue. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14powerpc/85xx: Add the workaround for erratum CPC-A002 (enable on P4080)Kumar Gala
CoreNet Platform Cache single-bit tag error scrubbing will cause tag corruption. Disable the feature to workaround the issue. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14powerpc/8xxx: Move fsl_is_spd() into generic 8xxx ddr codeKumar Gala
Move the parsing of hwconfig to determine if to use spd into common code so we can share it across all boards instead of duplicating it everywhere. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14fsl_esdhc: Add the workaround for erratum ESDHC136 (enable on P4080)Roy Zang
False multi-bit ECC errors will be reported by the eSDHC buffer which can trigger a reset request. We disable all ECC error checking on SDHC. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14fsl_esdhc: Add the workaround for erratum ESDHC135 (enable on P4080)Roy Zang
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host controller capabilities register (HOSTCAPBLT) are incorrect. The default of these bits should be zero instead of one. Clear these bits out when we read HOSTCAPBLT. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14fsl_esdhc: Add the workaround for erratum ESDHC111 (enable on P4080)Jerry Huang
Do not issue a manual asynchronous CMD12. Instead, use a (software) synchronous CMD12 or AUTOCMD12 to abort data transfer. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14powerpc/86xx: Enable common SRIO init codeKumar Gala
Add the needed defines and code to utilize the common 8xxx srio init code to setup LAWs and modify device tree if we have SRIO enabled on a board. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14powerpc/8xxx: Refactor SRIO initialization into common codeKumar Gala
Moved the SRIO init out of corenet_ds and into common code for 8xxx/QorIQ processors that have SRIO. We mimic what we do with PCIe controllers for SRIO. We utilize the fact that SRIO is over serdes to determine if its configured or not and thus can setup the LAWs needed for it dynamically. We additionally update the device tree (to remove the SRIO nodes) if the board doesn't have SRIO enabled. Introduced the following standard defines for board config.h: CONFIG_SYS_SRIO - Chip has SRIO or not CONFIG_SRIO1 - Board has SRIO 1 port available CONFIG_SRIO2 - Board has SRIO 2 port available (where 'n' is the port #) CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup) CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup) [ These mimic what we have for PCI and PCIe controllers ] Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14fsl_pci: Update PCIe boot ouputPeter Tyser
This change does the following: - Adds printing of negotiated link width. This information can be useful when debugging PCIe issues. - Makes it optional for boards to implement board_serdes_name(). Previously boards that did not implement it would print unsightly output such as "PCIE1: Connected to <NULL>..." - Rewords the PCIe boot output to reduce line length and to make it clear that the "base address XYZ" value refers to the base address of the internal processor PCIe registers and not a standard PCI BAR value. - Changes "PCIE" output to the standard "PCIe" Before change: PCIE1: connected to <NULL> as Root Complex (base addr ef008000) 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 05 PCIE2: connected to <NULL> as Endpoint (base addr ef009000) PCIE2: Bus 06 - 06 After change: PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device PCIe1: Bus 00 - 05 PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000 PCIe2: Bus 06 - 06 Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14powerpc/fsl-pci: Add generic code to setup PCIe controllersKumar Gala
Since all the PCIe controllers are connected over SERDES on the SoCs we can utilize is_serdes_configured() to determine if a controller is enabled. After which we can setup the ATMUs and LAWs for the controller in a common fashion and allow board code to specify what the controller is connected to for reporting reasons. We also provide a per controller (rather than all) for some systems that may have special requirements. Finally, we refactor the code used by the P1022DS to utilize the new generic code. Based on patch by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14powerpc/fsl-pci: Determine pci_controller based on cfg addr for dts fixupKumar Gala
Previously we passed in a specifically named struct pci_controller to determine if we had setup the particular PCI bus. Now we can search for the struct so we dont have to depend on the name or the struct being statically allocated. Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct back by searching for it means we can do things like dynamically allocate them or not have to expose the static structures to all users. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14powerpc/85xx: Fix bug in dcache_disableKumar Gala
We set the L1 dache register with a bogus register value. Need to be using 'r3' instead of 'r0'. Reported-by: John Traill <john.traill@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2025-01-05 20:40:35 +0000