| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
It also enables commands for cache enable/disable/status.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
This patch adds armv7m instruction & data cache support.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
|
|
Recent Linux distributions (e.g. Debian 9) include cross-compilers for
AArch64, but only for the aarch64-linux-gnu triplet only. It can thus
be expected that users will attempt to use the system cross-compiler
(instead of an aarch64-elf variant) to compile U-Boot for their ARMv8
target systems.
One key differences between an aarch64-linux-gnu and an aarch64-elf
compiler are the default settings regarding position-independent: with
the aarch64-linux-gnu compiler, the default will create and use the
global offset table.
This change-set adjusts the list of sections copied on ARMv8 to include
the GOT sections. With this added, the list matches the previous setup
for AArch32 closely.
Note that this is not an 'academic' issue, but was in fact encountered
by our QA during testing of the RK3399-Q7 BSP and resulted in an
early failure of the SPL stage during FDT setup.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
commit 56b0730157f70dc23d6caff9e7ceb8b377b96b9f upstream.
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Those DT will be part of 4.10, sync them so we can have our own config.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add the i2c-gpio nodes for fuelgauge and max77693.
There are i2c8 and i2c9.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
With d53ecad92f06 some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
trini: Disable CONFIG_SPL_USE_ARCH_MEMSET on orangepi_2
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This header file is used by three archs. It could be used by all of them
since relocation is a common function. Move it into a generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This header file is used by two archs. It could be used by all of them
since it allows the cache to be on during relocation. Move it into a
generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We don't need this PPC-specific function in generic code. Move it to
the powerpc directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
At present we misuse print_cpuinfo() do so CPU init on x86. This is done
because it is the next available call after the console is enabled. But
several arches use checkcpu() instead. Despite the horrible name (which
we can fix), it seems a better choice.
Adjust the various x86 CPU implementations to move their init code into
checkcpu() and use print_cpuinfo() only for printing CPU info.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Move these two function calls into checkcpu(), which is called on this
arch immediately after these two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
We don't need a special hook for sandbox as one of the later ones will do
just as well. We can print error messages about bad options after we
print the banner. In fact, it seems better.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This function is called just before checkcpu() on MPX83xx. Move it to the
code for that arch.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
There is no good reason to use a different name on PowerPC. Change it to
timer_init() like the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
We can just call this from the only place that needs it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
We can just call this from the only function that needs it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
We really don't need to have a name like this in the generic init
sequence. Use the generic get_clocks() name so that we can merge these
two at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
While x86 is the only user and this could in principle be moved to
arch_cpu_init() there is some justification for this being a separate
call. It provides a way to handle init which is not CPU-specific, but
must happen before the CPU can be set up.
Rename the function to be more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
There is no need to have this call in the generic init sequence and no
other architecture has needed it in the time it has been there. Move it
into sandbox's private code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
The OpenRISC architecture is currently unmaintained, remove.
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The SPARC architecture is currently unmaintained, remove.
Cc: Francois Retief <fgretief@spaceteq.co.za>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The architecture is currently unmaintained, remove.
Cc: Benjamin Matthews <mben12@gmail.com>
Cc: Chong Huang <chuang@ucrobotics.com>
Cc: Dimitar Penev <dpn@switchfin.org>
Cc: Haitao Zhang <hzhang@ucrobotics.com>
Cc: I-SYST Micromodule <support@i-syst.com>
Cc: M.Hasewinkel (MHA) <info@ssv-embedded.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Strubel <strubel@section5.ch>
Cc: Peter Meerwald <devel@bct-electronic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Valentin Yakovenkov <yakovenkov@niistt.ru>
Cc: Wojtek Skulski <info@skutek.com>
Cc: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.
Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The Allwinner H5 Soc is bascially an H3 with high SRAM and ARMv8 cores.
As the peripherals and the pinmuxing are almost identical, we piggy
back on the shared MACH_SUN8I_H3_H5 config symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The DRAM controller in the Allwinner H5 SoC is again very similar to
the one in the H3 and A64.
Based on the existing socid parameter, add support for this controller
by reusing the bulk of the code and only deviating where needed.
These new bits set or cleared here and there have been mostly found by
looking at DRAM register dumps after using the H5 boot0 and comparing
them to what we set in the code. So for now it's mostly unclear what
those bits actually mean - hence the missing names and comments.
Also add the delay line parameters taken from the boot0 and libdram
disassembly.
Register setup differences between H5 and H3 are courtesy of Jens Kuske.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Every armv8 board needs the memory map, so change the #ifdef to
ARM64 to avoid enumerating every single board or SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
If we take the liberty to use register r0 to perform our bit set, we
should be nice enough to tell the compiler about it.
Add r0 to the clobber list to avoid potential mayhem.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
This patch adds a call to dm_remove_devices_flags() to
announce_and_cleanup() so that drivers that have one of the removal flags
set (e.g. DM_FLAG_ACTIVE_DMA_REMOVE) in their driver struct, may do some
last-stage cleanup before the OS is started.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Sort rk3288 boards in alphabetical order.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The (shared) rk3399.dtsi had defined the 'rockchip,vbus-gpio'
properties for each USB 3.0 controller.
As the GPIO usage will vary (e.g. one of those GPIOs shuts down one of
the regulators on the RK3399-Q7) between boards, we move this from the
shared dtsi into the device tree file for the EVB board which these
GPIO definitions match.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The RK3399-Q7 is a system-on-module featuring the Rockchip RK3399
in a Qseven-compatible form-factor.
These changes add a device-tree describing the board and its
interfaces for basic functionality (e.g. GbE, SPI, eMMC, SD-card).
This includes the following changes from the original development:
* dts: rk3399-puma: include DTS for RK3399-Q7 SoM in the Makefile
* dts: rk3399-puma: add gmac for the RK3399-Q7
This change enables the Gigabit Ethernet support on the RK3399-Q7.
* dts: rk3399-puma: use serial0 for stdout
* dts: rk3399-puma: prepare the sdmmc node for SPL booting
* dts: rk3399-puma: enable spi1 and spi5, add /spi1/spiflash
The RK3399-Q7 (Puma) unsually (this is a build-time option for
customised boards) has an on-module SPI-flash connected to SPI1.
As of today, this is a Winbond W25Q32DW (32MBit) device.
The SPI5 controller is routed to the Q7 edge connector and provides
general-purpose SPI connectivity for customer base-boards.
With some minor improvements on integration into our outbound tree
- explicitly modelled the SPI flash as 'spiflash' under spi0
[dts: rk3399-puma: explicitly model spi-flash under spi1]
- renamed the aliases to spi0 and spi1 to allow easier use of
commands and legacy (SPL) infrastructure... i.e. the controllers
will be 0 and 1 for 'sf probe', 'sspi', etc.
[dts: rk3399-puma: rename aliases to number spi as 0 and 1 for commands]
* dts: rk3399-puma: include SPI in the spl-boot-order property
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
