summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2015-05-04mmc: fsl_esdhc: Add peripheral clock supportYangbo Lu
The SD clock could be generated by platform clock or peripheral clock for some platforms. This patch adds peripheral clock support for T1024/T1040/T2080. To enable it, define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04mmc: fsl_esdhc: Add adapter card type identification supportYangbo Lu
Add adapter card type identification support by reading FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function, define CONFIG_FSL_ESDHC_ADAPTER_IDENT. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> [York Sun: resolve conflicts in README.fsl-esdhc] Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04powerpc/mpc85xx: Don't deref NULL if qman portal lacks cell-indexScott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04powerpc: add 2 common dcache assembly functionsValentin Longchamp
This patch defines the 2 flush_dcache_range and invalidate_dcache_range functions for all the powerpc architecture. Their implementation is borrowed from the kernel's misc_32.S file and replace the ones from mpc86xx and ppc4xx since they were equivalent. This is a fix for the problem introduced by this patch: http://patchwork.ozlabs.org/patch/448849/ Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04fsl/pci: Set CFG_READY for PCIe v3.0 and laterMinghuan Lian
Freescale PCIe controllers v3.0 and later need to set bit CFG_READY to allow all inbound configuration transactions to be processed normally when in EP mode. However, bit CFG_READY has been moved from PCIe configuration space to CCSR PCIe configuration register comparing previous version. The patch is to set this bit according to PCIe version. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04powerpc/t4rdb: Add SD boot support for T4240RDB boardChunhe Lan
This patch adds SD boot support for T4240RDB board. SPL framework is used. PBL initializes the internal RAM and copies SPL to it. Then SPL initializes DDR using SPD and copies u-boot from SD card to DDR, finally SPL transfers control to u-boot. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> [York Sun: Fix T4240RDB_SDCARD_defcofig] Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04drivers: usb: fsl: Workaround for Erratum A004477Nikhil Badola
Add a delay of 1 microsecond before issuing soft reset to the controller to let ongoing ULPI transaction complete. This prevents corruption of ULPI Function Control Register which eventually prevents phy clock from entering to low power mode Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04mpc85xx/T4240EMU: Remove T4240EMU boardYork Sun
T4240 SoC has been available for a long time. Emulator support is no longer needed. Signed-off-by: York Sun <yorksun@freescale.com>
2015-05-04powerpc/mpc85xx: Use GOT when loading IVORs post-relocationScott Wood
Commit 96d2bb952bb ("powerpc/mpc85xx: Don't relocate exception vectors") simplified IVOR initialization a bit too much, failing to use the post-relocation offset. This doesn't cause a problem with normal NOR boot, in which both the pre-relocation and post-relocation addresses are 64 KiB aligned. However, if TEXT_BASE is only 4 KiB aligned, such as for NAND/SD/etc. boot on some targets, as well as the QEMU target, the post-relocation address will not be the same in the lower 16 bits, as reserve_uboot() ensures that the relocation address is always 64 KiB aligned even if the pre-relocation address was not. Use the GOT to get the proper post-relocation offsets. Fixes: 96d2bb952bb ("powerpc/mpc85xx: Don't relocate exception vectors") Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Alexander Graf <agraf@suse.de> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Tested-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-29Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini
2015-04-29ARM: zynq: rename CONFIG_ZYNQ to CONFIG_ARCH_ZYNQMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29ARM: zynq: move SoC headers to mach-zynq/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-zynq/* -> arch/arm/mach-zynq/include/mach/* Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29ARM: zynq: move SoC sources to mach-zynqMasahiro Yamada
Move arch/arm/cpu/armv7/zynq/* -> arch/arm/mach-zynq/* Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29ARM: zynq: pass "-mfpu=neon" only to lowlevel_init.SMasahiro Yamada
The comment line in arch/arm/cpu/armv7/zynq/config.mk says that the option "-mfpu=neon" is necessary for compiling lowlevel_init.S. We do not have to give it to all the source files. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynqmp: Enable SDHCI0 optionsMichal Simek
Enable SDHCI0 for zynqmp. Add empty gpio.h because of sdhci requirement. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynqmp: Add SPI driver support for ZynqMPSiva Durga Prasad Paladugu
Added the SPI driver support for ZynqMP The controller is same as zynq SPI controller Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-04-29zynqmp: i2c: Enable i2c driver for zynqMPSiva Durga Prasad Paladugu
Enable the i2c driver for ZynqMP Also enable the eeprom for read and writes to eeprom on ZynqMP ZynqMP uses the same i2c controller as in Zynq Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynqmp: Add support for EMMC bootmodeMichal Simek
Add support for EMMC bootmode. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynqmp: Add support for emulation platform - VeloceMichal Simek
Add support for Veloce - zynqmp emulation platform. Platform doesn't support SDHCI. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynq: timer: Fix wrong timer calculationSiva Durga Prasad Paladugu
Fix wrong timer calculation in get_timer_masked incase of overflow. This fixes the issue of getting wrong time from get_timer() calls. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynqmp: Add support for R5 sw loadingMichal Simek
Add support for loading sw for R5 with enabling for zynqmp. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2015-04-29zynqmp: caches: Enable dcache for zynqmpSiva Durga Prasad Paladugu
Define the mmu table till 2MB granularity enable dcaches for zynqmp. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynq: slcr: Disable all level shiftersSiva Durga Prasad Paladugu
Disable all level shifters before enabling the PS-to-PL level shifters as it would be good to disable all level shifters before enabling the PS-to-PL in order to ensure that it is in proper state Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29ARM: zynq: drop legacy ps7_init.c/h supportMasahiro Yamada
We are about to change the location for ps7_init files, breaking the current work-flows. It is good time to drop the legacy ps7_init.c/h support. Going forward, please use ps7_init_gpl.c/h all the time. If you are still using old Xilinx tools that are only able to generate ps7_init.c/h, rename them into ps7_init_gpl.c/h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Sören Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29zynq: Add Zynq PicoZed board supportNathan Rossi
The PicoZed is a System-on-Module board which is marketed as part of the ZedBoard/MicroZed/etc. collection. It includes a Zynq-7000 processor. This patch adds support that covers all the variants of the PicoZed including the SKUs with Z7010/Z7020 and Z7015/Z7030 Zynq chips. This patch set however only covers support for the System-on-Module and does not cover any extra components that are available on carrier boards (except those that are fanned out of the module itself). More information on this board, its variants and available carrier boards is available at: http://zedboard.org/product/picozed Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29gpio: add Xilinx Zynq PS GPIO driverAndrea Scian
Most of the code is taken (and adapted) from Linux kernel driver. Just add CONFIG_ZYNQ_GPIO to you config to enable it Signed-off-by: Andrea Scian <andrea.scian@dave.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-28Merge branch 'master' of git://www.denx.de/git/u-boot-socfpgaTom Rini
2015-04-28Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-04-27socfpga: implement arria V socdk SPI flash config in dtsPavel Machek
Arria V SocDK has same QSPI and SPI flash configuration as Socrates. Add support for it. Signed-off-by: Pavel Machek <pavel@denx.de>
2015-04-24Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini
2015-04-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2015-04-24MIPS: implement device-tree handover to Linux kernelDaniel Schwierzeck
Add device-tree handover to Linux kernel conforming with MIPS UHI [1]. Register $a0 will be set to the reserved value -2. The address of the device-tree blob will be stored as KSEG0 address in $a1. $a2 and $a3 are set to zero. [1] http://prplfoundation.org/wiki/MIPS_documentation Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-04-24socfpga: implement socdk SPI flash config in dtsPavel Machek
SocDK has same QSPI and SPI flash configuration as Socrates. Add support for it. Signed-off-by: Pavel Machek <pavel@denx.de>
2015-04-23armv8/fsl-lsch3: Implement workaround for I2C erratum A009203York Sun
This erratum requires setting GLITCH_EN bit in debug register to enable digital filter to improve clock stability. Signed-off-by: York Sun <yorksun@freescale.com> CC: Heiko Schocher <hs@denx.de>
2015-04-23ls2085a: esdhc: Add esdhc support for ls2085aYangbo Lu
This patch adds esdhc support for ls2085a. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23armv8/ls2085ardb: Enable NAND SPL supportScott Wood
Enable NAND boot support using SPL framework. To boot from NAND, either use DIP switches on board, or "qixis_reset nand" command. Details of forming NAND image can be found in README. Signed-off-by: Scott Wood <scottwood@freescale.com> [York Sun: Remove +S from defconfig after commit 252ed872] Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23armv8/ls2085aqds: NAND boot supportScott Wood
This adds NAND boot support for LS2085AQDS, using SPL framework. Details of forming NAND image can be found in README. Signed-off-by: Scott Wood <scottwood@freescale.com> [York Sun: Remove +S from defconfig after commit 252ed872] Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23driver/ifc: Add 64KB page supportJaiprakash Singh
IFC has two register pages.Till IFC version 1.4 each register page is 4KB each.But IFC ver 2.0 register page size is 64KB each.IFC regiters structure is break into two viz FCM and RUNTIME.FCM(Flash control machine) registers are defined in PAGE0 and controls IFC generic functionality. RUNTIME registers are defined in PAGE1 and controls NAND and GPCM funcinality. FCM and RUNTIME structures defination is common for IFC version 1.4 and 2.0. Signed-off-by: Jaiprakash Singh <b44839@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23Merge branch 'master' of git://git.denx.de/u-boot-dmTom Rini
2015-04-23usb: host: Add ehci-vf USB driver for ARM Vybrid SoC'sSanchayan Maity
This driver adds support for the USB peripheral on Freescale Vybrid SoC's. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-04-23ARM: vf610: Initial integration for Colibri VF50/VF61Sanchayan Maity
This adds initial support for Colibri VF50/VF61 based on Freescale Vybrid SoC. - CPU clocked at 396/500 MHz - DDR3 at 396MHz - for VF50, use PLL2 as memory clock (synchronous mode) - for VF61, use PLL1 as memory clock (asynchronous mode) - Console on UART0 (Colibri UART_A) - Ethernet on FEC1 - PLL5 based RMII clocking (E.g. No external crystal) - UART_A and UART_C I/O muxing - Boot from NAND by default Tested on Colibri VF50/VF61 booting using serial loader over UART. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Acked-by: Stefan Agner <stefan@agner.ch>
2015-04-23ARM: vf610: Enable cachesStefan Agner
Enables caches which provides a rather huge speedup of the boot loader. Also mark the on-chip RAM as cachable since this is the area U-Boot runs from. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-04-23ARM: vf610: Add SoC and CPU type detectionSanchayan Maity
Vybrid product family consists of several rather similar SoC which can be determined by softare during boot time. This allows use of variable ${soc} for Linux device tree files. Detect VF5xx CPU's by reading the CPU count register. We can determine the second number of the CPU type (VF6x0) which indicates the presence of a L2 cache. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-04-23ARM: vf610: Enable external 32KHz oscillatorStefan Agner
Enable the SCSC (Slow Clock Source Controller) and select the external 32KHz oscillator. This improves the accuracy of the RTC. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-04-23ARM: vf610: Move DDR3 initialization to imx-commonSanchayan Maity
In order to avoid code duplication, move the DDR3 initialization to the common place under imx-common. Currently ROW_DIFF and COL_DIFF can be chosen from the board file. The JEDEC timings are specified using a common ddr3_jedec_timings structure. Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-04-23arm: am437x: mux: Update mux namesBryan De Faria
Correct and complete the mux names following AM437x Technical Reference Manual. Signed-off-by: Bryan De Faria <bdefaria-ext@adeneo-embedded.com>
2015-04-23m68k: add architecture-specific u-boot.ldsangelo@sysam.it
Add architecture-specific u-boot.lds and remove all board-specific u-boot.lds. All the .text customization that was board-specific have been moved inside the related include/configs, inside a LDS_BOARD_TEXT define. Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2015-04-23fastboot: ARM: OMAP5: Enable reboot-bootloaderDileep Katta
Implemented fb_set_reboot_flag() for OMAP5 to set an environment variable 'dofastboot' when reboot-bootloader called. This environment variable will be checked in boot command and fastboot will be called if the variable is set. If the bootcmd env variable of OMAP5 common is overwritten with board-specific command, then these changes will not apply. This was originally intended for DRA7 platform, but now applies to all OMAP5. Ref: http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=19da2e436e9806259cf1f4988b9e046ab256bf2c Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Dileep Katta <dileep.katta@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Make it check for !CONFIG_ENV_IS_NOWHERE as we can't saveenv() in that case] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-23ARM: DRA7: Set serial number environment variableDileep Katta
This patch populates serial number environment variable from die_id_0 and die_id_1 register values for DRA7xx boards. The function is added in omap common code so that this can be re-used. Serial# environment variable will be useful to show correct information in "fastboot devices" commands. Ref: http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=a6bcaaf67f6e4bcd97808f53d0ceb4b0c04d583c Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Dileep Katta <dileep.katta@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-23davinci: add support for omapl138-lcdk boardPeter Howard
Signed-off-by: Peter Howard <phoward@gme.net.au> [trini: Add config file, update for ..._ether_addr() -> ..._ethaddr() rename] Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2025-02-05 23:37:41 +0000