| Age | Commit message (Collapse) | Author |
|---|
|
Add device tree based on evaluation board pcb112.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
|
|
Add device tree based on evaluation board pcb111.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
|
|
Add device tree based on evaluation board pcb110.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
|
|
As the Ocelot and Luton SoCs, this family of SoCs are found
in Microsemi Switches solution.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
|
|
Thes patch change the luton base device tree to use the newly added
SPI bitbang driver.
It also updates the "mscc_luton_defconfig" to use the new driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.
Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
There is no real difference between the generic variant and
the custom variant except that the generic variant is more
optimised. This also saves 24 Bytes in the SPL binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
|
|
Discard ABI related sections which are not required for debugging.
Rearrange debug sections similar to Linux. Remove the remaining
explicitely specified sections in the unused part because those
sections are not created anymore or because the linker puts them
by default at the end of the ELF binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
|
|
This enables the use of the MSCC serial GPIO driver on the MSCC
VCoreIII 'ocelot' SOC, and add gpio-leds nodes to the pcb123 and
pcb120 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
|
|
This enables the use of the MSCC serial GPIO driver, and add gpio-leds
nodes to the 'luton' pcb090 and pcb091 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
|
|
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
|
|
This prepares individual device trees for MSCC luton-based reference
boards - pcb090 and pcb091.
Note: Even though the devices trees are quite common, they will differ
significantly in coming patches.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
|
|
The GPIO control function can be used for controlling alternate
functions associated with a GPIO.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
|
|
The PHY MIIM utility functions can/will be used for board detection
purposes.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
|
|
|
|
|
|
The SDMMC reset is missing from DT, so the reset manager cannot unreset
the SDMMC. Add the missing DT reset entry.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
The SPL option for USB gadget should be named after the option for u-boot
(CONFIG_USB_GADGET)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This allows us to properly map the USB controller indexes
Tested on dra76 evm, am572 evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Fixes for 2019.01
|
|
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return
32768Hz to reflect the reality.
This also keeps the values in sync with the Linux clock tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
The CPU banner printed is as following:
CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz
1. Drop the CPU:
2. Change vendor from Freescale to NXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
|
|
According to the data sheet bits 10-8 are PHYDRAM_CK_EN. Fix mask
to allow setting PHYDRAM_CK_EN correctly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
corruption
Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Building peach-pi smdk5420 and peach-pit with thumb mode for SPL
ends-up in the following error:
Error: Thumb encoding does not support an immediate here -- `msr cpsr_c,#0x13|0xC0'
Use an intermediate register to be able to use thumb for exynos5 SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
All the source code of sdram_rk3036.c are from Rockchip, update the
copyright to owned by Rockchip.
Because rockchip may use this copy of code both for open source
project and internal project, update the license to use both
GPL2.0+ and BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This is workaround for issue we can't get correct size for 4GB ram
in 32bit system and available before we really need ram space
out of 4GB, eg.enable ARM LAPE(rk3288 supports 8GB ram).
The size of 4GB is '0x1 00000000', and this value will be truncated
to 0 in 32bit system, and system can not get correct ram size.
Rockchip SoCs reserve a blob of space for peripheral near 4GB,
and we are now setting SDRAM_MAX_SIZE as max available space for
ram in 4GB, so we can use this directly to workaround the issue.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
imx for 2019.01
- introduce support for i.MX8M
- fix size limit for Vhybrid / pico boards
- several board fixes
- w1 driver for MX2x / MX5x
|
|
Remove unused DDRC register macros.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy
firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to
DRAM.
The boot log with Arm trusted firmware console enabled:
"
U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
PMIC: PFUZE100 ID=0x10
Normal Boot
Trying to boot from MMC2
NOTICE: Configureing TZASC380
NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty
NOTICE: BL31: Built : 09:28:54, Nov 8 2018
lpddr4 swffc start
NOTICE: sip svc init
U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800)
CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: Freescale i.MX8MQ EVK
DRAM: 3 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 using MAC address from ROM
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Introduce DDR driver for i.MX8M. The driver will be used by SPL to
initialze DDR PHY and DDR Controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce lpddr4 header file
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
No need to build bootaux in SPL stage
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
imximage.cfg will be used to generate the flash.bin
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce script to generate fit image for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add MMC BOOT Device for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Rename mx8m,MX8M to imx8m,IMX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
|
|
Introduce is_imx8mq header macro
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce CHIP_REV_2_1 macro.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
