summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2020-01-07stm32mp1: reset coprocessor status at cold bootFabien Dessenne
Reset ResourceTableAddress and CoprocessorState at cold boot, preserve these values at standby wakeup. Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com> Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-01-07stm32mp1: declare backup registers for coprocessorFabien Dessenne
Use the backup register #17 as coprocessor resource table address and backup register #18 as coprocessor state. Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com> Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-01-07Merge tag 'u-boot-imx-20200107' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx New for 2020.04 --------------- - New boards Embedded Artists COM board Xea Board - Switch to DM: Aristainetos boards Toradex colibri (DM_ETH) iCubox GE bx50v3 mx7dsabre (DM_ETH) cx9020 - New features: Bootaux with elf files Default SYS_THUMB_BUILD for i.MX6/7 - Fixes: DHCOM i.MX6 PDK Engicam i.MX8M tools (imx8m_image) Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/633679664
2020-01-07Merge tag 'u-boot-atmel-2020.04-a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel features for 2020.04 cycle This feature set is a patch series from Tudor Ambarus which includes parsing of the spi flash SFDP parser for SST flashes, and using those tables to retrieve unique saved per device MAC address. This is then used as base mac address on the SAMA5D2 Wireless SOM EK board.
2020-01-07ARM: mxs: spl_boot.c: make early_delay more robustRasmus Villemoes
It's true that booting normally doesn't take long enough for the register to roll (which actually happens in a little over an hour, not just a few seconds). However, the counter starts at power-on, and if the board is held in reset to be booted over USB, one actually risks hitting wrap-around during boot, which can both result in too short delays (if the "st += delay" calculation makes st small) and theoretically also unbound delays (if st ends up being UINT_MAX and one just misses sampling digctl_microseconds at that point). It doesn't take more code to DTRT, and once bitten, twice shy. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-01-07ARM: dts: imx6qdl-icore-1.5: Remove duplicate phy reset methodsMichael Trimarchi
Engicam i.CoreM6 1.5 Quad/Dual MIPI dtsi is reusing fec node from Engicam i.CoreM6 dtsi but have sampe copy of phy-reset-gpio and phy-mode properties. So, drop this phy reset methods from imx6qdl-icore-1.5 dsti file. Cc: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-07ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DLJagan Teki
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on the 1.5 version of the i.Core MX6 cpu module. The 1.5 version differs from the original one for a few details, including the ethernet PHY interface clock provider. With this commit, the ethernet interface works properly: SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver While before using the 1.5 version, ethernet failed to startup do to un-clocked PHY interface: fec 2188000.ethernet eth0: could not attach to PHY Similar fix has merged for i.Core MX6Q but missed to update for DL. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-07ARM: dts: icorem6: Sync engicam device trees from v5.4Jagan Teki
Sync Engicam device tree file from v5.4 linux-next. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-07arm: mxs: be more careful when enabling gpmi_clkRasmus Villemoes
The data sheet says that the DIV field cannot change while the CLKGATE bit is set or modified. So do it a little more carefully, by first clearing the bit, waiting for that to appear, then setting the DIV field. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-01-07arm: mxs: fix comments in arch_cpu_init to match the codeRasmus Villemoes
The comment says to clear the bypass bit, but in fact it sets it, thus selecting ref_xtal. And the next line of code does not set the divider to 12, but to (the reset value of) 1. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-01-07arm: mxs: fix register definitions for clkctrl_gpmi and clkctrl_sspXRasmus Villemoes
I tried clearing a bit by writing to hw_clkctrl_gpmi_clr, then busy-waiting for it to actually clear. My board hung. The data sheet agrees, these registers do not have _set, _clr, _tog, so fix up the definitions. git grep -E 'clkctrl_(gpmi|ssp[0-9])_' says that nobody uses those non-existing ops registers. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-01-07mach-imx: nandbcb: improve cmd helpIgor Opaniuk
Add info about supported i.MX7, improve details the usage of bcbonly subcommand. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07ddr: imx8m: Return error values from LPDDR4 trainingFrieder Schrempf
In cases when the same SPL should run on boards with i.MX8MM, that differ in DDR configuration, it is necessary to try different parameters and check if the training done by the firmware suceeds or not. Therefore we return the DDR training/initialization success to the upper layer in order to be able to retry with different settings if necessary. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2020-01-07arm: imx: Default to SYS_THUMB_BUILD for i.MX6/7Tom Rini
In the case of i.MX6 and i.MX7 family SoCs it is safe (from an errata point of view) to use thumb2 by default to save space. Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-01-07mach-imx: bootaux: elf firmware supportIgor Opaniuk
Currently imx-specific bootaux command doesn't support ELF format firmware for Cortex-M4 core. This patches introduces a PoC implementation of handling elf firmware (load_elf_image_phdr() was copy-pasted from elf.c just for PoC). ELF64 binaries isn't supported yet. This has the advantage that the user does not need to know to which address the binary has been linked to. However, in order to handle and load the elf sections to the right address, we need to translate the Cortex-M4 core memory addresses to primary/host CPU memory addresses (Cortex A7/A9 cores). This allows to boot firmwares from any location with just using bootaux, e.g.: > tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr} Similar translation table can be found in the Linux remoteproc driver [1]. [1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.c Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07ARM: dts: imx7: imx7_colibri: introduce fec nodeIgor Opaniuk
Sync DTS with the mainline Linux and introduce fec node and regulator configuration for rn5t567 PMU. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07ARM: dts: imx6_apalis: introduce fec nodeIgor Opaniuk
Sync DTS with the mainline Linux and introduce fec node. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07ARM: dts: imx6_colibri: introduce fec nodeIgor Opaniuk
Sync DTS with the mainline Linux and introduce fec node. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07mx7dsabre: Enable DM_ETHJoris Offouga
Also sync device tree with v5.5-rc1 Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2020-01-07mx7ulp: Add support for Embedded Artists COM boardFabio Estevam
The Embedded Artists COM board is based on NXP i.MX7ULP. It has a BD70528 PMIC from Rohm with discrete DCDC powering option and improved current observability (compared to the existing NXP i.MX7ULP EVK). Add the initial support for the board. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-01-07imx: cx9020: migrate cx9020 to CONFIG_DM_USBSteffen Dirkwinkel
Note: gpio7_8 was never used for usb power regulator so we remove it here Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2020-01-07imx: cx9020: migrate cx9020 to CONFIG_DM_ETHSteffen Dirkwinkel
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2020-01-07imx: sync with kernel device tree for Phycore SoMParthiban Nallathambi
Sync the Linux Kernel 5.4-rc6 device tree for Phytec Phycore SoM and Segin board based on imx6UL and imx6ULL. Changes includes Phytec naming convention for the devicetree files. Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-01-07mach-imx: bootaux: add dcache flushing before enabling M4Igor Opaniuk
This patch fixes the issue with broken bootaux command, when M4 binary is loaded and data cache isn't flushed before M4 core is enabled. Reproducing: > tftpboot ${loadaddr} ${board_name}/hello_world.bin > cp.b ${loadaddr} 0x7F8000 $filesize > bootaux 0x7F8000 Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07mach-imx: bootaux: print stack pointer and reset vectorIgor Opaniuk
1. Change information printed about loaded M4 binary, print the stack pointer and reset vector addressed. 2. Add sanity check for the address provided as param. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07ARM: mx6: ddr: Add support for iMX6SXMarek Vasut
This patch adds support for iMX6SX MMDC into the DDR calibration code. The only difference between MX6DQ and MX6SX is that the SX has 2 SDQS registers, while the DQ has 8. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07ARM: mx6: ddr: Configure all SDQS pullups using loopMarek Vasut
Instead of explicitly setting up each SDQS register, use a loop. No functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07ARM: mx6: ddr: Factor out SDQS configuration codeMarek Vasut
Pull out the code turning SDQS pullups on and off into a separate function, since it is replicated in two places in the code and it is the single place in the entire function which is SoC dependent. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07ARM: mx6: ddr: Make debug prints work with tiny printfMarek Vasut
The %08X format returns just zeroes with tiny printf, which is horribly confusing, especially when debugging DRAM calibration problems. Change the format to %08x (with lowercase x), which behaves correctly with either implementation of printf in SPL. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Eric Nelson <eric@nelint.com>
2020-01-07ARM: dts: dh-imx6: add u-boot specific wdt-reboot nodeClaudius Heine
The wdt-reboot node is needed for the sysreset_watchdog driver to register a watchdog as a reset handler in case 'CONFIG_SYSRESET' is enabled. Signed-off-by: Claudius Heine <ch@denx.de>
2020-01-07arm: dts: hummingboard: add cubox/hummingboard DT (part 2 of 2)Baruch Siach
These DT files are copied from kernel v5.3 with no changes. This is part 2 of 2 commits. Included are DT files for SOM rev 1.5, and Hummingboard2 Gate/Edge. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-01-07arm: dts: hummingboard: add cubox/hummingboard DT (part 1 of 2)Baruch Siach
These DT files are copied from kernel v5.3 with no changes. This is part 1 of 2 commits. Included are DT files for the original Cubox-i and Hummingboard Base/Pro. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-01-07board: ge: mx53ppd: use imx wdtRobert Beckett
Enable DM imx WDT Enable SYSRESET_WATCHDOG to maintain WDT based reset ability Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07board: ge: bx50v3: use imx wdtRobert Beckett
Enable DM imx WDT Enable SYSRESET_WATCHDOG to maintain WDT based reset ability Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07board: ge: ppd: sync device tree from LinuxRobert Beckett
Copy device tree from linux for PPD. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07board: ge: bx50v3: sync devicetrees from LinuxRobert Beckett
Copy device trees from linux, keeping them as separate files for each board to ease future sync. Update board code to use generic bx50v3 dt initially, then select the specific dt based on board detection. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07imx: Add support for i.MX28 based XEA boardLukasz Majewski
This patch introduces support for i.MX28 based XEA board. This board supports DM/DTS in U-Boot proper as well as DM aware drivers in SPL (u-boot.sb) by using OF_PLATDATA. More detailed information regarding usage of it can be found in ./board/liebherr/xea/README file. U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200) Trying to boot from MMC1 MMC0: Command 8 timeout (status 0xf0344020) mmc_load_image_raw_sector: mmc block read error U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200) CPU: Freescale i.MX28 rev1.2 at 454 MHz BOOT: SSP SPI #3, master, 3V3 NOR Model: Liebherr (LWE) XEA i.MX28 Board DRAM: 128 MiB MMC: MXS MMC: 0 Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB OK In: serial Out: serial Err: serial Net: Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2 eth0: ethernet@800f0000 Hit any key to stop autoboot: 0 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-01-07imx6: aristainetos: add support for rev C boardHeiko Schocher
add support for revision C boards. This board has no longer a NAND. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add aristainetos 2b cslHeiko Schocher
add aristainetso board version CSL. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: readd aristainetos 2b boardHeiko Schocher
readd aristainetos 2b board. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add DM_SERIAL supportHeiko Schocher
add DM_SERIAL support for the aristainetos board, and remove not used code from board code. remove CONSOLE_OVERWRITE_ROUTINE. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: prepare dts for other board versionsHeiko Schocher
as we switch to support DM and DTS, rework the existing DTS trees. Change also Linux specific Device trees, goal is to push this changes to linux. Collect U-Boot specific changes in separate "*u-boot*" dts files. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add device tree from linuxHeiko Schocher
Add device trees from Linux in preparation for driver model conversions. device tree files taken from Linux: 71ae5fc87c34: "Merge tag 'linux-kselftest-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest" and added SPDX license identifier. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: remove 2b versionHeiko Schocher
remove 2b version of aristainetos board, as it is easier to make the DM / DTS port and introduce the 2b board version again (also some more board version). Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: move defines to KconfigHeiko Schocher
move defines, which are already moved to Kconfig out of board config. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: remove aristainetos boardHeiko Schocher
remove not anymore used aristainetos board. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-06Merge branch 'next'Tom Rini
Bring in the following merges: commit 8fbbec12f7d2c18f8883f3371cfca74a98b5dd87 Merge: 87f69f467a83 63618e71e89b Author: Tom Rini <trini@konsulko.com> Date: Fri Jan 3 09:48:47 2020 -0500 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next - updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support commit 87f69f467a8335b171c71bf217d2625d515acd7c Merge: c0912f9bbfb2 4466b9970319 Author: Tom Rini <trini@konsulko.com> Date: Tue Dec 24 08:18:19 2019 -0500 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next - Enable DM driver on ppc/km boards - Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x, T104x, P4080, P2041, P2020, P1020, P3041 - Some updates in mpc85xx-ddr driver, km boards commit c0912f9bbfb26dd03d189953678691b799d35b6e Merge: 533c9f5714bd a1d6dc3f8407 Author: Tom Rini <trini@konsulko.com> Date: Wed Dec 18 07:20:19 2019 -0500 Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next - Various x86 common codes updated for TPL/SPL - I2C designware driver updated for PCI - ICH SPI driver updated to support Apollo Lake - Add Intel FSP2 base support - Intel Apollo Lake platform specific drivers support - Add a new board Google Chromebook Coral commit 533c9f5714bdba79dc6f2629284d4c1a08a611d1 Merge: 553cb0688782 033e18b47bd0 Author: Tom Rini <trini@konsulko.com> Date: Tue Dec 17 07:53:08 2019 -0500 Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next i2c: for next - misc: i2c_eeprom: Add partition support and add ability to query size of eeprom device and partitions - i2c common: add support for offset overflow in to address and add sandbox tests for it. commit 553cb06887825314e74a9bdac337467c77d1db88 Merge: f39abbbc531e b4f98b3b16ec Author: Tom Rini <trini@konsulko.com> Date: Thu Dec 12 08:18:59 2019 -0500 Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next buildman improvements including toolchain environment feature sandbox unicode support in serial
2020-01-03arm: mach-k3: Enable WA for R5F deadlockLokesh Vutla
On K3 devices there are 2 conditions where R5F can deadlock: 1.When software is performing series of store operations to cacheable write back/write allocate memory region and later on software execute barrier operation (DSB or DMB). R5F may hang at the barrier instruction. 2.When software is performing a mix of load and store operations within a tight loop and store operations are all writing to cacheable write back/write allocates memory regions, R5F may hang at one of the load instruction. To avoid the above two conditions disable linefill optimization inside Cortex R5F which will make R5F to only issue up to 2 cache line fills at any point of time. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-03arm: dts: k3-j721e: ddr: Update to 0.2 version of DDR config toolLokesh Vutla
Update the ddr settings to use the DDR reg config tool rev 0.2.0. This reduces the aging count(in DDRSS_CTL_274_DATA reg) to 15 in-order to avoid DSS underflow errors. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Kevin Scholz <k-scholz@ti.com>
2020-01-02Merge tag 'u-boot-rockchip-20191231' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fix latest mainline kernel for rk3308 - Update rk3288-evb config to suport OP-TEE - Fix for firefly-px30 DEBUG_UART channel and make it standalone - Script make_fit_atf add python3 support - Fix rk3328 timer with correct COUNTER_FREQUENCY - Fix rk3328 ATF support with enable spl-fifo-mode
generated by cgit (git 2.34.1) at 2024-12-29 00:56:38 +0000