| Age | Commit message (Collapse) | Author |
|---|
|
Add USB related DT entries to enable USB device mode.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add the basic a72 basic dts for j7200. Following nodes were supported:
- UART
- MMC SD
- I2C
- TISCI communication
- LPDDR with 1600MTs configuration.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
|
|
Add the basic a72 dts for j7200. Following nodes were supported:
- UART
- MMC SD
- I2C
- TISCI communication
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Detect if sysfw is already loaded by ROM and pass this information to
sysfw loader. Based on this information sysfw loader either loads the
sysfw image from boot media or just receives the boot notification
message form sysfw.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
|
|
Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. ROM passes this information on number of images that are loaded
to bootloader at certain location. Add support for storing this
information before it gets corrupted.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
|
|
The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
It is targeted for automotive gateway, vehicle compute systems,
Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
The SoC aims to meet the complex processing needs of modern embedded
products.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, two clusters of lockstep
capable dual Cortex-R5F MCUs and a Centralized Device Management and
Security Controller (DMSC).
* Configurable L3 Cache and IO-coherent architecture with high data
throughput capable distributed DMA architecture under NAVSS.
* Integrated Ethernet switch supporting up to a total of 4 external ports
in addition to legacy Ethernet switch of up to 2 ports.
* Upto 1 PCIe-GEN3 controller, 1 USB3.0 Dual-role device subsystems,
20 MCANs, 3 McASP, eMMC and SD, OSPI/HyperBus memory controller, I3C and
I2C, eCAP/eQEP, eHRPWM among other peripherals.
* One hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
management.
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
Add support for detection J7200 SoC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
|
|
In main control mmr there is no partition 4 and partition 6 is available
only on J721e. Fix the same in ctrl_mmr_unlock function
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
|
|
Add an api soc_is_j721e(), and use it to enable certain functionality
that is available only on j721e. This detection is needed when DT is not
available.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
|
|
Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. In such cases, SPL need not load sysfw from boot media, but need
to receive boot notification message from sysfw. So separate out
remoteproc calls for system controller from sysfw loader and just
receive the boot notification if sysfw is already loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
|
|
mmr_unlock api is common for all k3 devices. Move it to a common
location.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
|
|
If SPL_MULTI_DTB_FIT is not enabled, then CONFIG_SPL_OF_LIST is not defined
And in turn tispl.bin ends up not embedding any DTB.
Fixing it by using CONFIG_DEFAULT_DEVICE_TREE if SPL_OF_LIST is empty.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Guard all eeprom probe with TI_I2C_BOARD_DETECT to avoid reading eeprom
when eeprom is not available
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Add nodes for USB0 in SPL to enable USB host boot mode
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Add USB0 nodes and set them to host mode to support USB host and
peripheral boot modes
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Add support for identifying USB host and device boot modes
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
U-boot only supports either USB host or device mode for a node at a
time in dts. To support both host and dfu bootmodes, set "peripheral"
as the default dr_mode but fixup property to "host" if host bootmode
is detected.
This needs to happen before the dwc3 generic layer binds the usb device
to a host or device driver. Therefore, add an fdtdec_setup_board()
implementation to fixup the dt based on the boot mode.
Also use the same fixup function to set the USB-PCIe Serdes mux to PCIe
in both the host and device cases. This is required for accessing the
interface at USB 2.0 speeds.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
config
Gate mmc related system related configurations with DM_MMC to avoid build
errors when MMC is not enabled
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Add support for loading system firmware from a USB mass storage device
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
In order to be able to use things like file system drivers early on in
SPL (before relocation) in a memory-constrained environment when DDR is
not yet available we cannot use the simple malloc scheme which does not
implement the freeing of previously allocated memory blocks. To address
this issue go ahead and enable the use of the full malloc by manually
initializing the required functionality inside board_init_f by creating
a full malloc pool inside the pre-relocation malloc pool.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
The various CBASS interconnect nodes on K3 J721E SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
|
|
The various CBASS interconnect nodes on K3 AM65x SoCs are defined
using the node name "interconnect". This is not a valid node name
as per the dt-schema. Fix these node names to use the standard name
used for SoC interconnects, "bus".
Signed-off-by: Suman Anna <s-anna@ti.com>
|
|
This commit completes the migrations for DM_ETH and DM_USB. The board
is now consistent with omap3_beagle and other remaining OMAP3 boards.
Cc: Tom Rini <trini@konsulko.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
When switching on or off the ARM caches some care must be taken to ensure
existing cache line allocations are not left in an inconsistent state.
An example of this is when cache lines are considered non-shared by
and L3 controller even though the lines are shared. To prevent these
and other issues all cache lines should be cleared before enabling
or disabling a coherent master's cache. ARM cores and many L3 controllers
provide a way to efficiently clean out all cache lines to allow for
this, unfortunately there is no such easy way to do this on current K3
MSMC based systems.
We could explicitly clean out every valid external address tracked by
MSMC (all of DRAM), or we could attempt to identify only the set of
addresses accessed by a given boot stage and flush only those
specifically. This patch attempts the latter. We start with cleaning the
SPL load address. More addresses can be added here later as they are
identified.
Note that we perform a flush operation for both the flush and invalidate
operations, this is not a typo. We do this to avoid the situation that
some ARM cores will promote an invalidate to a clean+invalidate, but only
emit the invalidation operation externally, leading to a loss of data.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Add DT entries for main domain watchdog0 and 1 instances on the J721e
well as RTI1-based watchdog on the AM65x. RTI0 does not work for this
purpose on the AM65x, so leave it out.
On AM65x, we mark the power-domain as shared because RTI firmware such
as https://github.com/siemens/k3-rti-wdt may request it as well in order
to prevent accidental shutdown of the watchdog.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
|
|
Add LED support for Cortina Access Presidio Engineering Board
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Simon Glass <sjg@chromium.org>
|
|
Factor out ppc-specific bdinfo setup from generic init sequence to
arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
|
|
Factor out m68k-specific bdinfo setup to arch_setup_bdinfo in
arch/m68k/lib/bdinfo.c. Also, use if(IS_ENABLED()) instead of #ifdef where
possible.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
|
|
Move all assignments to gd->bd->bi_mem{start,size} to generic code in
setup_bdinfo.
Xtensa architecture is special in this regard as it defines its own
handling of gd->bd->bi_mem{start,size} fields. In order to avoid defining
a weak SDRAM function, let arch_setup_bdinfo overwrite the generic flags.
For ARC architecture, remove ARCH_EARLY_INIT_R from Kconfig since it is
not needed anymore.
Also, use gd->ram_base to populate bi_memstart to avoid an ifdef.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Alexey Brodkin <abrokdin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
bi_sramstart and bi_sramsize are generic members of the bd_info structure,
so move the m68k/powerpc-specific prints to generic code. Also, print them
only if SRAM support is enabled via CONFIG_SYS_HAS_SRAM.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
|
|
Update the MikroTik CRS305-1G-4S flash layout to support redundant UBI
partitions.
Additionally enable the UBI commands in crs305-1g-4s_defconfig.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
- r2dplus updates
|
|
We still have some platforms that only implements functionalities in
PSCI 0.1 (e.g. Allwinner ARMv7 SoCs).
Add a Kconfig option for exporting only PSCI 0.1. The code to export
PSCI 0.1 is still available and gets activated by this patch.
In addition, default ARCH_SUNXI U-Boot PSCI implementation to export
PSCI 0.1, to fix poweroff/reboot regression on Allwinner multi-core
ARMv7 SoCs.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
|
|
SPL_CLEAR_BSS is called regardless of build type if
CONFIG_SPL_EARLY_BSS is defined. Add a guard for CONFIG_SPL_BUILD
to fix.
Signed-off-by: Brian Moyer <bdm310@gmail.com>
|
|
This patch adds a feature for block device cloning similar to dd
command, this should be useful for boot-strapping a device where
usb gadget or networking is not available. For instance one can
clone a factory image into a blank emmc from an external sd card.
Signed-off-by: John Chau <john@harmon.hk>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
|
|
- add DM based reset driver for SiFive SoC's.
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- doc: fix qemu-mips build instructions
- MIPS: add GPIO, CLK and SPI drivers for Octeon MIPS64
|
|
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
PRCI module within SiFive SoC's has register with which we can
reset the sub-systems within the SoC. The resets to DDR and ethernet
sub systems within FU540-C000 SoC are active low, and are hold low
by default on power-up. Currently these are directly asserted within
prci driver via register read/write.
With the DM based reset driver support here, we bind the reset
driver with clock (prci) driver and assert the reset signals of
both sub-system's appropriately.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
|
|
The resets to DDR and ethernet sub-system are connected to
PRCI device reset control register, these reset signals
are active low and are held low at power-up. Add these reset
producer and consumer details needed by the reset driver.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
|
|
This patch selects DM_SPI & DM_I2C for MIPS Octeon. DM_GPIO, DM_SERIAL
and DM_ETH are already selected.
Additionally the selections are now alphabetically sorted.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add the SPI flash DT node for the EBB7304.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add the Octeon SPI DT node to the dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch adds the DT nodes for the Octeon clock support via the
common clk_ API.
Signed-off-by: Stefan Roese <sr@denx.de>
|
