summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)Author
2019-10-08imx: wandboard: convert FEC support to DM_ETHAnatolij Gustschin
Remove CONFIG_DM_ETH conversion warning to avoid board removal. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-10-08dts: imx28: Remove #include "imx28.dtsi" from imx28-u-boot.dtsi fileLukasz Majewski
After this change it is possible to use imx28-<board>-u-boot.dtsi with the imx28-u-boot.dtsi explicitly included without breaking setup from imx28-<board>.dts file. The problem is that the imx28.dtsi included in a wrong place overrides the changes made in imx28-<board>.dts. As a result some devices are "disabled" in the final DTB. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon modeLukasz Majewski
This change tries to fix the following problem: - The board boots (to be more precise - ROM loads SPL) from a slow SPI-NOR memory. As a result the spl_boot_device() will return SPI-NOR as a boot device (which is correct). - The problem is that in 'falcon boot' the eMMC is used as a boot medium to load kernel from its partition. Calling spl_boot_device() will break things as it returns SPI-NOR device. To fix this issue the new CONFIG_SPL_FORCE_MMC_BOOT Kconfig flag is introduced to handle this special use case. By default it is not defined, so there is no change in the legacy code flow. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: WDT: Convert WDT driver to use DM/DTS (including SYSRESET)Lukasz Majewski
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover, the SYSRESET_WATCHDOG driver is used to support 'reset' command. As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is enabled for it. This allows the legacy SPL code to work properly. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL)Lukasz Majewski
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not supported as of time of this conversion. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: eth: Switch display5 board to use DM_ETHLukasz Majewski
After this commit the display5 device would use FEC driver supporting driver model (DM_ETH). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: mmc: Switch display5 board to use DM_MMC and BLK (USDHC)Lukasz Majewski
After this commit the display5 device would use eMMC driver supporting driver model (DM_MMC and BLK). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: I2C: Switch display5 board to use DM_I2CLukasz Majewski
After this commit the display5 device would use I2C driver supporting driver model (DM_I2C). The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize on-bus devices according to device tree description. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08pico-imx6: Add initial supportFabio Estevam
Add the initial support for the pico-imx6 variants. DDR initialization is based on the TechNexion's U-Boot code. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08mx6: clock: Allow enable_ipu_clock() to be built for SPL codeFabio Estevam
Allow enable_ipu_clock() to be built for SPL code. This is done in preparation for configuring the NoC registers on i.MX6QP in SPL. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08configs: pico-imx7d: Convert to DM_VIDEOJoris Offouga
This commit convert all pico-imx7d to DM_VIDEO Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-10-08ARM: dts: pico-imx7d: sync device tree with v5.3-rc6Joris Offouga
Synchronize device tree with v5.3-rc6 label Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-10-08ARM: dts: pico-imx7d: Add u-boot.dtsi for uboot specific dts changeJoris Offouga
This commit introduce u-boot.dtsi Signed-off-by: Joris Offouga <offougajoris@gmail.com> Suggested-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: cpu: fix mac fuse word for i.MX8QMPeng Fan
i.MX8QM does not share same FUSE MAC word index, so update the word index for i.MX8QM. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: move i.MX8 cpu desc code to drivers/cpu/imx8_cpu.cPeng Fan
Move cpu desc code to cpu driver directory and name it imx8_cpu.c No functional change. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: scu_api: add sc_pm_is_partition_startedPeng Fan
Add sc_pm_is_partition_started to check whether a partition has been started. This will be used to detect M4 partition booted up or not, then we could choose which dtb to use. If M4 is up, we need use dtb, such as imx8qm-mek-rpmsg.dtb. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: fdt: add optee nodePeng Fan
Add OP-TEE device tree node for Linux according to args passed from ATF. If ATF has been built with OP-TEE running, boot_pointer[1] will indicate that. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: save args passed from ATFPeng Fan
We use information from ATF to know whether OP-TEE is running or not. So save args passed from ATF. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: fdt: configure sid for mastersPeng Fan
On i.MX8QM, sid is programmable, so we could program sid according the value encoded in device tree. This patch support legacy bindings which are still being used by XEN and new bindings used by Linux Kernel. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: scu_api: add sc_rm_set_master_sidPeng Fan
Add sc_rm_set_master_sid to set stream sid of masters to make sure they could use smmu. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: disable node when the resource is not ownedPeng Fan
When resource is not assigned to non-secure Linux, if linux continue to use the node, linux may crash or hang. So need to set the node status to disabled for not owned resources. The resource id is in the power-domains property in device tree, so parse the power-domains property to get the resource id and use scfw api to check whether it is owned by current partition. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8qm: power up SMMUPeng Fan
There is SMMU in i.MX8QM. To use SMMU in Linux, need power up it. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: sys_proto: add is_imx8qm helperPeng Fan
Add is_imx8qm helper which could be used by SoC and Driver code. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: Probe the SCU driver by using uclass functionYe Li
Since SCU MU driver has been bound in dm_init, so we don't need to bind it again. Just replace by using uclass function to probe it. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: add container targetPeng Fan
To support SPL loading container file, add a new Makefile target, and introduce a new Kconfig file to source the cfg file which will be parsed by mkimage. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: support parsing i.MX8 Container filePeng Fan
Add parsing i.MX8 Container file support, this is to let SPL could load images in a container file to destination address. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: imx6qdl: dtsi: move U-Boot specific change to u-boot.dtsiPeng Fan
The changes were added by following patch: commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video") commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes") Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08Kconfig: Migrate CONFIG_CSF_SIZE to KconfigBreno Matheus Lima
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000. mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08i.MX7ULP: Change clock rate calculation for NIC1 BUS and EXTYe Li
On i.MX7ULP B0, there is change in NIC clock dividers architecture. On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but on B0 they are parallel with NIC1 DIV. So now the dividers are independent. This patch modifies the scg_nic_get_rate function according to this change. Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Set A7 core frequency to 500Mhz for B0 chipYe Li
The normal target frequency for ULP A7 core is 500Mhz, but now ROM set the core frequency to 413Mhz. So change it to 500Mhz in u-boot. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Add CPU revision check for B0Peng Fan
Since there is no register for CPU revision, we use ROM version to check the A0 or B0 chip. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Workaround APLL PFD2 to 345.6MhzYe Li
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28) to workaround the problem. The correct fix should let GPU handle the clock rate in kernel. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix SPLL/APLL clock rate calculation issueYe Li
The num/denom is a float value, but in the calculation it is convert to integer 0, and cause the result wrong. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix wrong i2c configuration nameYe Li
Wrong I2c driver configuration name is used in codes, so I2c driver is not built. Correct it. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Add CONFIG_MX7ULP to kconfigYe Li
Since many drivers need this CONFIG_MX7ULP to distiguish the settings for i.MX7ULP only. Add this entry to cpu's kconfig. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix PCC register bits mask and offset issueYe Li
The offset for FRAC and the mask for PCD are not correct. If we set FRAC, we can't get the right frequency. Fix them to correct value. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Correct the clock indexBai Ping
On i.MX7ULP, value zero is reserved in SCG1 RCCR register, so the val should be decreased by 1 to get the correct clock source index. Signed-off-by: Bai Ping <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: Fix system reset after a7 rtc alarm expired.Bai Ping
The board will reboot if A7 core enter mem mode by rtc, then M4 core enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode to fix this issue. Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access it. So check the CPU rev and not apply the settings for B0. Signed-off-by: Bai Ping <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: i.MX7ULP: add get_boot_devicePeng Fan
Add get_boot_device for i.MX7ULP Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Fabio Estevam <festevam@gmail.com>
2019-10-08nitrogen6x: migrate to using device treeTroy Kisky
Migrate to using device tree required for further driver model integration. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08ARM: imx: Support larger SPL size on IMX6DQRobert Hancock
Previously the SPL size on all iMX6 platforms was restricted to 68KB because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the other iMX6 variants have 256KB of OCRAM. Add an option CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which don't need to support the SL/DL variants. This allows for an SPL size of 196KB, which makes it much easier to use configurations such as SPL with driver model and FDT control. Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
2019-10-08spl: imx: only use HAB if spl fit signature is not enabledRicardo Salveti
There is no need to use HAB for FIT signature validation when SPL_FIT_SIGNATURE is also enabled, as that will be validated via the normal U-Boot signed FIT image flow. This allows having SPL validated by HAB and the payloads to follow being validated with FIT signatures only. Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: apalis_imx6: select MX6Q via KconfigRicardo Salveti
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q variants, which are quite similar and already managed via only one dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in order to automatically enable the HAS_CAAM and MX6_SMP features. Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08arm: dts: imx: fsl-imx8qm.dtsi: add gpio aliases to fix gpio commandPeng Fan
The gpio command currently uses equal bank names "GPIO0_" for all existing gpio banks, i. e.: U-Boot# gpio status -a Bank GPIO0_: GPIO0_0: input: 0 [ ] GPIO0_1: input: 0 [ ] ... Bank GPIO0_: GPIO0_0: input: 0 [ ] GPIO0_1: input: 0 [ ] ... So the command is broken, it is not possible to address a desired bank. Add gpio aliases to fix this. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08spl: pass args to board_return_to_bootromPeng Fan
Pass spl_image and bootdev to board_return_bootrom. i.MX8MN needs the args to let ROM to load images Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-10-08imx: mx6ul_14x14_evk: convert to DM_VIDEOPeng Fan
To support DM_VIDEO, Add display node for lcdif Drop board iomuxc settings. Enable DM_VIDEO Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-08imx: add i.MX6ULZ boardPeng Fan
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible with i.MX6ULL. so most code of i.MX6ULL can be reused by i.MX6ULZ. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08imx: add i.MX6ULZ cpu typePeng Fan
Add i.MX6ULZ cpu type and helper. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08arm: dts: import dts for i.MX6ULZPeng Fan
Import kernel dts for i.MX6ULZ from commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08arm: dts: sync dts for i.MX6ULLPeng Fan
Sync kernel dts for i.MX6ULL from commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux") Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
generated by cgit (git 2.34.1) at 2024-12-30 21:58:35 +0000