| Age | Commit message (Collapse) | Author |
|---|
|
At present this uses u32 to store an address. We should use unsigned long
and avoid special types in function return values and parameters unless
necessary. This makes the code more portable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We should use unsigned long rather than u32 for addresses. Update this so
that the table-generation code builds correctly on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Basically rename X86_SUBARCH_MRST to X86_SUBARCH_INTEL_MID to be more specific.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
configs/ls1046aqds_defconfig
configs/ls1046aqds_nand_defconfig
configs/ls1046aqds_qspi_defconfig
configs/ls1046aqds_sdcard_ifc_defconfig
configs/ls1046aqds_sdcard_qspi_defconfig
configs/ls1046ardb_emmc_defconfig
configs/ls1046ardb_qspi_defconfig
configs/ls1046ardb_sdcard_defconfig
|
|
eLBC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock ratio register (LCRR) used in
current implementation governs eLBC IP output cloc.
Update sys_info->freq_localbus to represent eLBC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable ELBC from Kconfig.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Enable IFC from Kconfig.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
PPA binary needs to be relocated on secure DDR, hence marking out
a portion of DDR as secure if CONFIG_SYS_MEM_RESERVE_SECURE flag
is set
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
|
|
The memcpy() function returns a pointer to trg.
Signed-off-by: Mark Marshall <Mark.Marshall@omicron.at>
Reviewed-by: Thomas Graziadei <thomas.graziadei@omicronenergy.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
The patch implements secure booting for the mvebu architecture.
This includes:
- The addition of secure headers and all needed signatures and keys in
mkimage
- Commands capable of writing the board's efuses to both write the
needed cryptographic data and enable the secure booting mechanism
- The creation of convenience text files containing the necessary
commands to write the efuses
The KAK and CSK keys are expected to reside in the files kwb_kak.key and
kwb_csk.key (OpenSSL 2048 bit private keys) in the top-level directory.
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
ddaa905 ("arm: mvebu: Add DM (driver model) support") removed the
assignment of the gd pointer, but kept the (now superfluous) declaration
of the gd pointer.
Remove this declaration.
Signed-off-by: Reinhard Pfau <pfau@gdsys.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Allow boards to do some initialization when PCIe comes up.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Armada 38x has four PCI ports, not three.
The optimization in pci_init_board() seems to assume that every port has
three lanes. This is obviously wrong, and breaks support for Armada 38x.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
We should use the symbolic names for the cache control bits.
Signed-off-by: Mark Marshall <Mark.Marshall@omicron.at>
Reviewed-by: Thomas Graziadei <thomas.graziadei@omicronenergy.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
To enable DM on MPC83xx, we need pre-relocation malloc, which is
implemented in this patch.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[York S: Fixed compiling warning for unused variable 'i']
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The r1 register is modified several times during the cache-ram setup of
the MPC83xx SoCs.
Since this SP modification confuses debuggers, we use a general purpose
register to compute the new stack pointer value, and only set the SP
once after all computations are done.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Erratum A-008336 applies to LS1046A per latest SoC document.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
|
|
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch provides u-boot support for Liebherr (LWN) mccmon6 board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The pinmuxing for i.MX53 FEC ethernet copied from
<kernel>/arch/arm/boot/dts/imx53-qsb-common.dtsi (at least until v4.9)
was bad. It is different from the manual pinmuxing in
<u-boot>/board/freescale/mx53loco/mx53loco.c which was used in
cx9020 implementation previously before mainlining into u-boot.
It seems the bug in imx53-qsb kernel device tree is hidden for so long,
because it was never used, by the kernel driver.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
|
|
Now U-Boot proper need not get the uniphier_boards array. Compile
it only for SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Make it look like cmd_ddrphy.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Just cosmetic changes:
- Rename prefix DMPHY_ to MPHY_ for consistency
- Move UMC parameters below for complete decouple of PHY and UMC
- Remove redundant whitespaces
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
It seems more readable to use arrays to get SoC specific parameters
instead of the crappy switch statement.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
For LD20 SoC, the last 64 byte of each DRAM bank is used for the
dynamic training of DRAM PHY. The regions must be reserved in DT to
prevent the kernel from using them. Now gd->bd->bi_dram reflects
the actual memory banks. Just use it instead of getting access to
the board parameters.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
U-Boot needs to set up available memory area(s) in dram_init() and
dram_init_banksize(). It is platform-dependent how to detect the
memory banks. Currently, UniPhier adopts the memory banks _alleged_
by DT. This is based on the assumption that users bind a correct DT
in their build process.
Come to think of it, the DRAM controller has already been set up
before U-Boot is entered (because U-Boot runs on DRAM). So, the
DRAM controller setup register seems a more reliable source of any
information about DRAM stuff. The DRAM banks are initialized by
preliminary firmware (SPL, ARM Trusted Firmware BL2, or whatever),
so this means the source of the reliability is shifted from Device
Tree to such early-stage firmware. However, if the DRAM controller
is wrongly configured, the system will crash. If your system is
running, the DRAM setup register is very likely to provide the
correct DRAM mapping.
Decode the SG_MEMCONF register to get the available DRAM banks.
The dram_init() and dram_init_banksize() need similar decoding.
It would be nice if dram_init_banksize() could reuse the outcome
of dram_init(), but global variables are unavailable at this stage
because the .bss section is available only after the relocation.
As a result, SG_MEMCONF must be checked twice, but a new helper
uniphier_memconf_decode() will help to avoid code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The two arrays ddrphy_{op,ip}_dq_shift_val, occupy more than 3.8 KB
memory footprint, which is significant in SPL.
There are PHY parameters for 5 boards, but they are actually not
board specific, but SoC specific. After all, we just need to have
2 patterns, for LD20 and LD21. Also, the shift values are small
enough to become "short" type instead of "int". This change will
save about 3 KB memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch adds support for the QSPI IP found in stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
|
|
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Use the clock setup function defined in clock.c instead of setting the
clock bits directly in the drivers.
Remove register definitions of RCC in rcc.h as these are already
defined in the struct in stm32.h
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
The fmc base address is defined twice, once in fmc.h and once in stm32.h.
Fix wrong definition in stm32.h.
Remove the definiton in fmc.h.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Cleanup stm32f7 files:
- use BIT macro
- use GENMASK macro
- use rcc struct instead of macro additions
Add missing stm32f7 register in rcc struct
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA<vikas.manocha@st.com>
|
|
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.
Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
|
|
The check for OMAP3630/3730 only checks for 800MHz 3630/3730, but
anything else is lumped into 36XX/37XX with an assumed 1GHz speed.
Based on the DM3730 TRM bit 9 shows the MPU Frequency (800MHz/1GHZ).
This also adds the ability to distinguish between the DM3730, DM3725,
AM3715, and AM3703 and correctly display their maximum speed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
|
|
Frequency is measured in Hz.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
|
|
This feature seems to be sometimes misunderstood. The intention is:
[1] Bring the slaves into the U-Boot proper image, not SPL (unless
you have a special reason to do otherwise).
[2] The operation must be done in a board (SoC) specific manner
since how to wake the slaves from the Boot ROM is SoC specific.
[3] The slaves must enter U-Boot proper after U-Boot relocates
itself because the "cpu-release-addr" property points to the
relocated memory area.
[2] is already explained in the help. We can make [1] even clearer
by mentioning "U-Boot proper" instead of "U-Boot". [3] is missing,
so I am adding it to the list. Instead, "before the master CPU
jumps to the kernel" is a matter of course, so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
chiliBoard is a development board which uses chiliSOM as its base.
Hardware specification:
* chiliSOM (TI AM335x, DRAM, NAND)
* Ethernet PHY (id 0)
* USB host (usb1)
* MicroSD slot (mmc0)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
chiliSOM is a System On Module (http://http://grinn-global.com/chilisom/).
It can't exists on its own, but will be used as part of other boards.
Hardware specification:
* TI AM335x processor
* 128M, 256M or 512M DDR3 memory
* up to 256M NAND
We place source inside arch/arm/mach-omap2/ directory and make it
possible to reuse initialization code (i.e. DDR, NAND init) for all
boards that use it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
ast2500 Eval Board device tree and board specific configuration.
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add configuration file with parameters that are very likely to be shared by
all ast2500-based boards.
Add ast2500-board.c file with the init code that is very likely to be
shared by all ast2500-based boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.
Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.
Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This re-syncs us with the official and full list of MACH_TYPE_xxx values
from http://www.armlinux.org.uk/developer/machines/
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
The LS1046A processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
