| Age | Commit message (Collapse) | Author |
|---|
|
These functions relate to memory init so move them into the init
header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
To get memory size from device tree instead of
get_ram_size(). This can avoid memory access fault
in U-Boot proper after PMP configurations in OpenSBI.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
|
|
This patch provides four configurations which can support U-Boot SPL
to boot from RAM or FLASH and then boot FIT image including OpenSBI
FW_DYNAMIC firmware and U-Boot proper images from RAM or MMC boot devices.
With ae350_rv[32|64]_spl_defconfigs:
U-Boot SPL will be loaded by gdb or FSBL and runs in RAM in machine mode
and then load FIT image from RAM device on AE350.
With ae350_rv[32|64]_spl_xip_defconfigs:
U-Boot SPL can be burned into SPI flash and run in flash in machine mode
and then load FIT image from SPI flash or MMC device on AE350.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
|
|
Find the UCLASS_CACHE driver to configure the cache controller's
settings.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When AE350 boots from flash, use CONFIG_OF_SEPARATE instead of
CONFIG_OF_BOARD.
Also remove unused code about prior_stage_fdt_address.
And modify CONFIG_SYS_FDT_BASE as flash address.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
Add two defconfigs to support AE350 SMP booting from flash.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
Remove cpu name from the defconfig naming.
Because other cpus maybe run on AE350 platform.
So only use platfrom name in defconfig naming
will be better.
Also sync MAINTAINERS:
Rename
a25-ae350_32_defconfig as ae350_rv32_defconfig
ax25-ae350_64_defconfig as ae350_rv64_defconfig
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
There is no need to expose RISCV_NDS to the Kconfig menu as it is
an ax25-specific option. Introduce a dedicated Kconfig option for
the cache ops of ax25 platform and use that to guard the cache ops.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
ax25-ae350 use CONFIG_OF_BOARD via a2 and CONFIG_SYS_SDRAM_BASE
to boot from ram which allow the board to override the fdt
address originally.
But after this patch
riscv: save hart ID and device tree passed by prior boot stage
It provide prior_stage_fdt_address which offer a temporary
memory address to keep the dtb address passing from loader(gdb)
to u-boot with a1.
So passing via a2 and CONFIG_SYS_SDRAM_BASE is redundant and
can be removed. And it also somehow may corrupted BBL if it
was be arranged in CONFIG_SYS_SDRAM_BASE.
In board_fdt_blob_setup()
When boting from ram:
prior_stage_fdt_address will be use to reserved dtb temporarily.
When booting from ROM:
dtb will be pre-burned in CONFIG_SYS_FDT_BASE, if it is flash base.
Or CONFIG_SYS_FDT_BASE maybe a memory map space (NOT RAM or ROM)
which is provided by HW.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
|
|
|
|
Since the mach_id is not used by RISC-V, remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
Add smc_init() to get register base from dts and
deal with atfsmc020 controler initialzation job.
Write protect is enabled by default. So WP shall
be disabled when startup, then cfi flash can be
detected and erasing and writing can be executed.
Adp-ae3xx and adp-ag101p both do smc initilize job
in lowlevel_init.S and get register base fron
CONFIG_FTSMC020_BASE. They also can be moved those
codes to board stage. Remind them as todo jobs.
After that CONFIG_FTSMC020_BASE can be removed.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
Rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Enable CONFIG_OF_BOAD to support delivery dtb to u-boot
at run time instead of embedded.
There are two methods to delivery dtb.
1 Pass from loader:
When u-boot boot from RAM, gdb or loader can pass dtb
via a2 to u-boot dynamically. Of course gdb or loader
shall be in charge of dtb delivery.
2 Configure CONFIG_SYS_FDT_BASE:
It can be configured as RAM or ROM base statically,
no mater u-boot boot from RAM or ROM.
If it was configured as ROM base, dtb can be burned
into ROM(spi flash) by spi driver.
Meanwhile remove CONFIG_SKIP_LOWLEVEL_INIT which is
useless in nx25-ae250 configuration.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
Remove board_mmc_init() in adp-ag101p, adp-ae3xx
and nx25-ae250 boards.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
Add nx25-ae250 board to do platform initializations.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
|
|
AG101P/AE3XX enable ftsdc010 dm flow.
Signed-off-by: Rick Chen <rick@andestech.com>
|
|
Add #include <asm/mach-types.h> to fix it.
Signed-off-by: rick <rick@andestech.com>
|
|
With a few tweaks we can avoid including these files, which are only
needed by two C files.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
Boot linux kernel via dhcp and bootm ok.
NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4899 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'boomimage-310y-ae300-spi.bin'.
Load address: 0x600000
Loading: #################################################################
#################################################################
#################################################################
...
...
###################################
233.4 KiB/s
done
Bytes transferred = 13872076 (d3abcc hex)
NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4592 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'ae300.dtb'.
Load address: 0x2000000
Loading: #
82 KiB/s
done
Bytes transferred = 2378 (94a hex)
NDS32 # bootm 0x600000 - 0x2000000
Image Name:
Created: 2017-03-22 6:52:03 UTC
Image Type: NDS32 Linux Kernel Image (uncompressed)
Data Size: 13872012 Bytes = 13.2 MiB
Load Address: 0000c000
Entry Point: 0000c000
Verifying Checksum ... OK
Booting using the fdt blob at 0x2000000
Loading Kernel Image ... OK
Loading Device Tree to 01efc000, end 01eff949 ... OK
Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
#293 PREEMPT Wed Mar 22 14:49:28 CST 2017
CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: rick <rick@andestech.com>
|
|
Support Andestech AE3xx platform: serial, timer device tree flow.
Signed-off-by: rick <rick@andestech.com>
|
|
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Remove ag101 and ag102 support
Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>
|
|
Add nds32 ag101p generic board support.
Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>
|
|
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Macpaul Lin <macpaul@gmail.com>
|
|
There is a missing in previous
commit 951344b778d6ac67b94011d942a5a55da7202027
(nds32: Convert Makefiles to use COBJS-y style)
will cause compile error.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
Cc: Andes <uboot@andestech.com>
Signed-off-by: Andes <uboot@andestech.com>
|
|
|
|
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The original adp-ag101/adp-ag101p initialize only one bank(64MB)
by default at boot time, but it is not enough for some application,
so increasing to two banks(128M).
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
|
|
Due to improper external function declaration,
building U-Boot for the adp-ag102 board shows
this warning:
adp-ag102.c: In function 'pci_init_board':
adp-ag102.c:95: warning: function declaration isn't a prototype
Include the 'faraday/ftpci100.h' header which
provides the proper declaration and remove the
local declaration to get rid of the warning.
Compile tested only.
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
|
|
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
Add board specific files.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
|
|
Add softcore SoC ag101p and the board adp-ag101p support.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
|
|
Add evaluation board "adp-ag101" configuration file adp-ag101.h.
Add adp-ag101.c board config and related settings.
Add board adp-ag101 into boards.cfg
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
|
