summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2018-06-11LS1012AFRWY: Add Secure Boot supportVinitha V Pillai
Added the following: 1. defconfig for LS1012AFRWY Secure boot 2. PfE Validation support Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11board: ls1012a: FRWY-LS1012A board supportBhaskar Upadhaya
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> [yorks: rebase and fix SPDX tag] [yorks: fix board/freescale/ls1012afrdm/Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board: Kconfig: Re-Arrangement of PPA firmware and header addressesBhaskar Upadhaya
PPA firmware and header address may vary depending upon different boards, configure ppa firmware and header address in board specific Kconfig. Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board/freescale,lsch3: Add entry for 0.9vPriyanka Jain
As per updated hardware documentation for lsch3 based chips like LS2088A, 0.9v support has been added in possible supported SoC volatges Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-11Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-05-10board/freescale: Remove invalid fsl email addressesFabio Estevam
These fsl email addresses are no longer valid and they do not have a correspondent nxp.com entry. Remove all invalid fsl email addresses and mark the boards as orphan. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-05-10p1022ds: Change Timur's email addressFabio Estevam
timur@freescale.com is not a valid email for quite some time, so change it to Timur's updated email. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Timur Tabi <timur@tabi.org>
2018-05-09armv8: ls1088: Update 1900MT/s DDR timing to bring consistencyAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09armv8: ls1088aqds: Enable mdio commands on u-boot promptAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-01MAINTAINERS: Switch nxp.com domainFabio Estevam
freescale.com domain is no longer reachable, so switch the maintainers' emails to nxp.com domain instead. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-30Merge git://git.denx.de/u-boot-imxTom Rini
2018-04-27Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTRTom Rini
We have a large number of places where while we historically referenced gd in the code we no longer do, as well as cases where the code added that line "just in case" during development and never dropped it. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-26mx7dsabresd: Remove the mx7dsabresd_secure_defconfig targetFabio Estevam
mx7dsabresd_secure_defconfig was introduced to allow booting NXP kernel that has CAAM support and needs to boot in secure mode. Instead of keeping two different config targets for the same board, remove mx7dsabresd_secure_defconfig and select CONFIG_ARMV7_BOOT_SEC_DEFAULT inside mx7dsabresd_defconfig so that this target could be used to boot both mainline and the vendor kernel. This makes maintenance task easier and avoid potentially confusion for the end user. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
2018-04-15Merge git://git.denx.de/u-boot-imxTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15mx31ads: DeleteTom Rini
This platform has been marked as orphaned since September 2013, remove. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-22board: freescale: ls1012a2g5rdb: enable network support on ls1012a2g5rdbCalvin Johnson
This patch enables ethernet support for ls1012a2g5rdb. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22board: freescale: ls1012ardb: enable network support on ls1012ardbCalvin Johnson
This patch enables ethernet support for ls1012ardb. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22board: freescale: ls1012afrdm: enable network support on ls1012afrdmCalvin Johnson
This patch enables ethernet support for ls1012afrdm. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22board: freescale: ls1012aqds: enable network support on ls1012aqdsCalvin Johnson
This patch enables ethernet support for ls1012aqds. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-20armv8: ls1088aqds: Add IFC-NOR as boot source for LS1088Ashish Kumar
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT. Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and IFC-NOR to be used as flash. This allows writing to IFC-NOR flash. QSPI and DSPI cannot be accessed in this defconfig. IFC-NOR image is generated using ls1088aqds_defconfig. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20armv8: ls1088a: Add i2c_early_init() func for LS1088AQDSAshish Kumar
This function is required for enabling access to early i2c function for correct usage of QIXIS_READ and QIXIS_WRITE. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-20armv8: ls1088a: Add clock related function in CONFIG_SPL_BUILDAshish Kumar
get_board_ddr_clk(), get_board_sys_clk() and if_board_diff_clk() is now available for SPL build. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-03-05libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>Masahiro Yamada
Thomas reported U-Boot failed to build host tools if libfdt-devel package is installed because tools include libfdt headers from /usr/include/ instead of using internal ones. This commit moves the header code: include/libfdt.h -> include/linux/libfdt.h include/libfdt_env.h -> include/linux/libfdt_env.h and replaces include directives: #include <libfdt.h> -> #include <linux/libfdt.h> #include <libfdt_env.h> -> #include <linux/libfdt_env.h> Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-02-04mx6memcal: enable SDP supportEric Nelson
The initial implementation of mx6memcal reset the CPU after running the memory calibration procedure because the generic board has no information about which boot devices are available. Now that we have SDP support in SPL, use it to allow a full U-Boot to be uploaded (i.e. to use "mtest"). Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-04arm: imx: mx53loco: remove usage of mx53_dram_sizePatrick Bruenn
Static variables are not available during board_init_f(). 'static uint32_t mx53_dram_size[2];' was used in board specific dram_init(), dram_init_banksize() and get_effective_memsize() to avoid multiple calls to get_ram_size(). Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2018-01-30armv8: ls2088ardb: Add 3DS RDIMM supportYork Sun
Tested with MTA72ASS8G72PSZ-2S6G1. This is 3DS RDIMM module with x4 DDR chips. LS2088ARDB needs to be modified to connect all DQS signals. Some of them are grounded by default for x8 chips. Tested with RDIMM MTA18ASF2G72PDZ on main memory controllers. DP-DDR doesn't support RDIMM. Dropped related timing table. Signed-off-by: York Sun <york.sun@nxp.com>
2018-01-30armv8: ls1046ardb: Add RDIMM supportYork Sun
This adds 2Rx8 RDIMM on LS1046ARDB board. Tested with RDIMM MTA18ASF2G72PDZ and MTA9ASF1G72PZ. Signed-off-by: York Sun <york.sun@nxp.com>
2018-01-23fsl: common: qixis: Add ifc and emmc switching via qixisAshish Kumar
Currently only SD, NAND can be secondary boot sources controlled by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR can be secondary boot source, while QSPI-NOR is the primary. Add options in qixis to switch to other boot sources including ifc and emmc. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23armv8: ls1088a: vid: Compiling VID specific functions for SPLRajesh Bhagat
Enables and compiles VID specific functions for SPL. Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23ls1088a: Add VID support for QDS and RDB platformsRajesh Bhagat
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems. It reads the fusesr register and changes the VDD accordingly by adjusting the voltage via LTC3882 regulator. This patch also takes care of the special case of 0.9V VDD is present in fusesr register. In that case,it also changes the SERDES voltage by disabling the SERDES, changing the SVDD and then re-enabling SERDES. Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23common: board_f: vid: Add VID specific API to adjust core voltageRajesh Bhagat
Adds a VID specific API in init_sequence_f and spl code flow namely init_func_vid which is required to adjust core voltage. VID specific code is required in spl, hence moving flag CONFIG_VID out of spl flags. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23ls1088a: ddr: configure DDR for 0.9v for VID supportRajesh Bhagat
When VID feature is supported, check the contents of fuse register and configure DDR operate at 0.9v. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Add support for LTC3882 voltage regulator chipRajesh Bhagat
Restructures common driver to support LTC3882 voltage regulator chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23Kconfig: Add LTC3882 voltage regulator configRajesh Bhagat
Adds below LTC3882 voltage regulator config: CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Move IR chip specific code in flagRajesh Bhagat
Moves IR chip (IR36021) specific code in flag to resolve compilation issue where it is not present. For example, LS1088A is having a new LTC3882 voltage chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Add board specific vdd adjust APIRajesh Bhagat
Adds a board specific API namely board_adjust_vdd which is required to define the board VDD adjust settings. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common:vid: Add LS1088A VID Supported voltage valuesRajesh Bhagat
Adds below voltage values supported by LS1088A Soc: 1.025V(default), 0.9875V, 0.9750V, 0.9V, 1.0V, 1.0125V, 1.0250V. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-19powerpc: Drop unreferenced CONFIG_* definesTuomas Tynkkynen
The following config symbols are only defined once and never referenced anywhere else: CONFIG_CYRUS CONFIG_IDS8313 CONFIG_MPC8308_P1M CONFIG_MPC8308RDB CONFIG_MPC8349EMDS CONFIG_MPC8349ITXGP CONFIG_SBC8349 CONFIG_SBC8548 CONFIG_SBC8641D CONFIG_TQM834X CONFIG_VE8313 CONFIG_XPEDITE5140 CONFIG_XPEDITE5200 CONFIG_XPEDITE550X Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Mario Six <mario.six@gdsys.cc>
2018-01-19m68k: Drop unreferenced CONFIG_* definesTuomas Tynkkynen
The following config symbols are only defined once and never referenced anywhere else: CONFIG_AMCORE CONFIG_ASTRO5373L CONFIG_M52277EVB CONFIG_M5253DEMO CONFIG_M5253EVBE CONFIG_M5275EVB CONFIG_M54418TWR CONFIG_STMARK2 Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-01-17Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-01-17freescale: Ensure common commands are not included in SPL binaryTom Rini
Both the "qixis_reset" and esbc_validate" commands can only be used in full U-Boot so do not build them in SPL. As part of this rework the qixis code to declare things as static and make use of __weak for function aliases. Cc; York Sun <york.sun@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15arm: ls1021atwr: Rework local commands to not be included in SPLTom Rini
Move some of the code for the "lane_bank" and "cpld" code local commands so that they are not built for SPL as they can only be used in full U-Boot. This means we can mark a few functions as static as well now. Cc: Alison Wang <alison.wang@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: York Sun <york.sun@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Alison Wang <alison.wang@nxp.com> Tested-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15powerpc: P1010RDB: Rework local command to not be included in SPLTom Rini
Add a CONFIG_SPL_BUILD guard around the code for the "mux" command so it is not included in SPL. Cc: Qiang Zhao <qiang.zhao@nxp.com> Cc: York Sun <york.sun@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com> Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
2018-01-15board/ls2081ard: Correct code to get QMAP value in checkboardPriyanka Jain
QMAP value contains information about QSPI chip-selects. These bits are used to display information of boot device in checkboard() function. QMAP value is stored in most significant 3-bits of 8-bit register brdcfg[0] in Qixis, this patch corrects code to get QMAP bits using below logic: (brdcfg[0] >> 5) & 0x7 Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15board/ls2081ardb: Update board related printsPriyanka Jain
Remove Board Arch print as its value is always constant '1' and does not contain any important information to display during boot. Add print to display Board FPGA version. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15configs: SECURE_BOOT: Enable CONFIG_CMD_EXT4_WRITESumit Garg
As part of chain of trust with confidentiality along with distro boot, linux kernel image needs to be stored in encrypted form on ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of Secure boot on ARM based platforms. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15board: ls1012a: LS1012A-2G5RDB board supportBhaskar Upadhaya
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-12mx6memcal: spl: Disambiguate the error messageFabio Estevam
Currently mmdc_do_dqs_calibration() and mmdc_do_write_level_calibration() show the same error message, which is confusing for debugging. Disambiguate the mmdc_do_dqs_calibration() error message. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-12mx6memcal: spl: Also take i.MX6ULL into accountFabio Estevam
i.MX6ULL also does not support 64-bit DDR bus, so add it to the check logic. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-27 22:15:24 +0000