| Age | Commit message (Collapse) | Author |
|---|
|
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
|
|
This patch configures and initializes the L2 switch on T1040rdb board.
The external L2 switch ports may be connected to PHYs only over
QSGMII, for T1040rdb.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
|
|
This patch configures and initializes the L2 switch on T1040QDS board.
The L2 switch ports must be initialized according to the SerDes
protocols.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
|
|
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Sinan Akman <sinan@writeme.com>
Cc: Tom Rini <trini@ti.com>
|
|
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T1024RDB-PB board adds 2.5G SGMII support with AQR105 PHY.
rcw_0x095 is used for 10G XFI + 3x PCIex1
rcw_0x135 is used for 2.5G SGMII + 2x PCIex1
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Besides, added SPI/SD/NAND boot deep sleep support.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Secure boot target is added for T1042RDB platform.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
SerDes 2 protocol 56 is not valid any longer due to
the new RCW; protocol 55 is used instead, so add
SerDes 2 protocol 55 to align with RCW.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Secure boot target is added for P5040DS platform.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add NOR and SPI flash secure boot target for C29XPCIE board.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Mingkai.Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
|
|
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rune Torgersen <runet@innovsys.com>
|
|
|
|
Add spi nor boot support for mx6slevk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Configure the pad setting and enable qspi clock to support qspi
flashes access.
Add QSPI related macro in configuration header file.
Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
get_board_rev() just returns the cpu revision, which does not make it really
useful for distinguishing between revisions of the board.
Let's get rid of get_board_rev() as it is not being used with its correct
meaning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
As per the mx51evk schematics MX51EVK_USB_CLK_EN_B is GPIO2_1, not GPIO2_2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add pinmux settings and implement board_ehci_hcd_init
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
Add pinmux settings, implement board_ehci_hcd_init and board_ehci_power
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
A new interface is introduced to support generic board structure.
Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Conflicts:
board/freescale/mx6sxsabresd/mx6sxsabresd.c
Signed-off-by: Tom Rini <trini@ti.com>
|
|
|
|
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The Freescale LS1021AQDS share some pins, so Add the hwconfig option
that allows the user to choose which the function he wants.
The main pin mux IP is:
eSDHC, SAI, IIC2, RGMII, CAN, SAI.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Through adding CONFIG_QIXIS_I2C_ACCESS macro,
QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used
for both i2c and ifc access to QIXIS FPGA. This is
more convenient for coding.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
When resuming from deep sleep, the I2C channel may not be
in the default channel. So, switch to the default channel
before accessing DDR SPD.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
BRDCFG1_EMI1_SEL_MASK has been changed to 0x78, which contains
selection bits and connected status bit. So the Corresponding mux
value of RGMII is changed to BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The new device trees use a more generic interface for
supporting muxing mdio buses. The mux property is thus
specified in "reg", rather than "fsl,hydra-mdio-muxval".
In order to support using old device trees, we keep the
old fixup in there. Linux will therefore see the both
properties, but will ignore fsl,hydra-mdio-muxval.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Initialize retimer for XFI on t1024qds.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add multiplexing support among SPI flash, TDM riser card and SDXC.
it routes SPI pins to SPI flash by default.
Route SPI pins to SD slot if "adaptor=sdxc" is set in hwconfig.
Route SPI pins to TDM riser card and do fixup for dts if "pin_mux=tdm"
is set in hwconfig.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0,
and also update core frequency to 1.8GHz for v1.1.
We reserve the support for T2080 v1.0 and enable v1.1 by default.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
