summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2016-09-14fsl: csu: add an API to set individual device access permissionHou Zhiqiang
Add this API to make the individual device is able to be set to the specified permission. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14arm: fsl-layerscape: move forward the non-secure access permission setupHou Zhiqiang
Move forward the basic non-secure access enable operation, so the subsequent individual device access permission can override it. And collect the dispersed callers in board level, and then move them to SoC level. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14board: ls1043ardb: move sec_init to board_initSumit Garg
sec_init() which was earlier called in misc_init_r() is now done in board_init() before PPA init as SEC block will be used during PPA image validation. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-06mx6ul_14x14_ev: Enable the CCGR clocks earlierFabio Estevam
To be in the safe side we need to enable the CCGR clocks prior to calling arch_cpu_init(). Inspired by Tim Harvey's commit d783c2744f9 ("imx: ventana: fix boot to SD"). Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com> Tested-by: Eric Nelson <eric@nelint.com>
2016-09-06mx6ul_14x14_evk: Adjust SPL DDR3 settingsFabio Estevam
Adjust DDR3 initialization done in SPL by comparing them against the NXP DCD table. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06mx6ul_14x14_evk: Pass refsel and refr fields to avoid hangFabio Estevam
When running a NXP 4.1 kernel with U-Boot mainline on a mx6ul-evk, we observe a hang when going into the lowest operational point of cpufreq. This hang issue does not happen on the NXP U-Boot version. After comparing the SPL DDR initialization against the DCD table from NXP U-Boot, the key difference that causes the hang is the MDREF register setting: DATA 4 0x021B0020 0x00000800 ,which means: REF_SEL = 0 --> Periodic refresh cycle: 64kHz REFR = 1 ---> Refresh Rate - 2 refreshes So adjust the MDREF initialization for mx6ul_evk accordingly to fix the kernel hang issue at low bus frequency. Reported-by: Eric Nelson <eric@nelint.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06mx6: ddr: Allow changing REFSEL and REFR fieldsFabio Estevam
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and REFR fields of the MDREF register as 1 and 7, respectively for DDR3 and 0 and 3 for LPDDR2. Looking at the MDREF initialization done via DCD we see that boards do need to initialize these fields differently: $ git grep 0x021b0020 board/ board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */ board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800 board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800 board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800 So introduce a mechanism for users to be able to configure REFSEL and REFR fields as needed. Keep all the mx6 SPL users in their current REF_SEL and REFR values, so no functional changes for the existing users. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2016-09-06mx7dsabresd: Directly write to register LDOGCTLFabio Estevam
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need to do a read-modify-write operation. Simplify the code by writing directly to this register. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06mx7dsabresd: Directly write to register LDOGCTLFabio Estevam
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need to do a read-modify-write operation. Simplify the code by writing directly to this register. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06mx6ul_14x14_evk: don't use array for SD2 card detect padEric Nelson
Only a single pad is changed to change sdhc2_dat3 from an SDIO pin to and from GPIO4:5, so remove the array and use the imx_iomux_v3_setup_pad() routine. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-09-06mx7dsabresd: Print secure/non-secure mode infoFabio Estevam
mx7dsabresd has two targets: - mx7dsabresd_defconfig: boots in non-secure mode - mx7dsabresd_secure_defconfig: boots in secure mode Print the mode that is being used to help users to easily identify which target is running on the board. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-08-26treewide: fix "followings" to "following"Masahiro Yamada
Most of them are my mistakes. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-02board/freescale: Update MAINTAINERS filesYork Sun
Update maintainers for secure boot targets. Signed-off-by: York Sun <york.sun@nxp.com>
2016-07-28Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-07-28mx7dsabresd: MAINTAINERS: Add mx7dsabresd_secure_defconfigFabio Estevam
Add an entry for the mx7dsabresd_secure_defconfig target. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-28mx6ul_14x14_evk: Remove unused defineDiego Dorta
Remove unused define constant. Signed-off-by: Diego Dorta <diego.dorta@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-26armv8: ls1043aqds: add IFC fixup in case QSPI is enabledQianyu Gong
QSPI and IFC are pin-multiplexed on LS1043AQDS board. If QSPI is enabled, IFC would not be initialized correctly. So disable the IFC node for Linux. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26ARMv7: PSCI: ls102xa: add more PSCI v1.0 functions implementionHongbo Zhang
This patch implements PSCI functions for ls102xa SoC following PSCI v1.0, they are as the list: psci_version, psci_features, psci_cpu_suspend, psci_affinity_info, psci_system_reset, psci_system_off. Tested on LS1021aQDS, LS1021aTWR. Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com> Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26armv8: ls1043aqds: Update MAINTAINERSYork Sun
Add ls1043aqds_lpuart_defconfig to file list. Signed-off-by: York Sun <york.sun@nxp.com>
2016-07-26armv8: ls2080aqds: Update MAINTAINERSYork Sun
Add ls2080aqds_qspi_defconfig to file list. Signed-off-by: York Sun <york.sun@nxp.com>
2016-07-26arm: ls1021atwr: Add SD secure boot targetSumit Garg
Add SD secure boot target for ls1021atwr. Implement board specific spl_board_init() to setup CAAM stream ID and corresponding stream ID in SMMU. Change the u-boot size defined by a macro for copying the main U-Boot by SPL to also include the u-boot Secure Boot header size as header is appended to u-boot image. So header will also be copied from SD to DDR. Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26SECURE_BOOT: Enable chain of trust in SPL frameworkSumit Garg
Override jump_to_image_no_args function to include validation of u-boot image using spl_validate_uboot before jumping to u-boot image. Also define macros in SPL framework to enable crypto operations. Reviewed-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-21powerpc/mpc85xx: T104x: Add nand secure boot targetSumit Garg
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC. In non-secure boot scenario from NAND, this address will map to CPC configured as SRAM. But in case of secure boot, this default address always maps to IBR (Internal Boot ROM). The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF. For secure boot target from NAND, the text base for SPL is kept same as non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000) As a the virtual and physical address of CPC would be different. The virtual address 0xFFFx_xxxx needs to be mapped to physical address 0xBFFx_xxxx. Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000 and update DCFG SCRTACH1 register with location of Header required for secure boot. The changes are similar to commit 467a40dfe35f48d830f01a72617207d03ca85b4d powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041 While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC is only 256K and thus SPL framework is used. The changes are only applicable for SPL U-Boot running out of CPC SRAM and not the next level U-Boot loaded on DDR. Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-21powerpc/mpc85xx: SECURE BOOT- Enable chain of trust in SPLSumit Garg
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate the next level U-boot image. Add a new function spl_validate_uboot to perform the validation. Enable hardware crypto operations in SPL using SEC block. In case of Secure Boot, PAMU is not bypassed. For allowing SEC block access to CPC configured as SRAM, configure PAMU. Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-19ARMv8/ls1043ardb: Integrate FSL PPAHou Zhiqiang
The PPA use PSCI to make secondary cores bootup. So when PPA was enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method between PSCI and spin-table. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-15armv8: Move secure_ram variable out of generic global dataYork Sun
Secure_ram variable was put in generic global data. But only ARMv8 uses this variable. Move it to ARM specific data structure. Signed-off-by: York Sun <york.sun@nxp.com>
2016-07-12mx6sxsabresd: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
2016-07-12mx6sxsabreauto: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12mx6slevk: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12mx6qsabreauto: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-28armv8: ls1043aqds: use configurable clockQianyu Gong
Get the clocks from FPGA through I2C, if IFC is disabled. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-24armv8: ls1043aqds: fix to get boot device info from FPGAQianyu Gong
The LBMAP switches on the board will tell which boot device is used. Only QSPI boot is supported if the boot device is IFCCard. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-18Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
2016-06-18Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-06-18imx: mx6ulevk: change QSPI PAD DSE to 120ohmPeng Fan
The current pad DSE for QSPI is 60ohm. This setting cause too strong drive to clock and data signals. Need to change the DSE to 120ohm for better signal quality. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx6ulevk: fix LCD_nPWREN settingPeng Fan
Q901 is PMOS, LCD_nPWREN should be at low voltage then output is 3V3. If LCD_nPWREN is high, output is 2.4V which is not correct. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx6ulevk: fix 74LV OE usagePeng Fan
Fix 74LV OE gpio index. gpio index is wrong, so gpio output will not have effect, since we use wrong GPIO5_IO18, but not correct GPIO5_IO8. And at the end of the initialization of 74lv init, should keep OE voltage level at LOW to make 74lv output the correct voltage. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18mx7dsabresd: Fix LCD_PWR_EN output settingYe Li
LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3 is actually 1.2V. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18mx6sabresd: Allow LVDS backlight to be functional after a kernel rebootMarco Franchi
Currently the LVDS backlight does not work in U-Boot after a “reboot” comand in the kernel. This problem occurs because the kernel uses this pin in PWM mode and U-Boot does not configure the backlight pin as GPIO functionality. So fix the problem by explicitly configuring the backlight pin as GPIO in U-Boot. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18Merge branch 'master' of git://git.denx.de/u-bootStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-06-13usb: xhci: fsl: Add workaround for USB erratum A008751Sriram Dash
This patch is doing the following: 1. Implementing the errata for LS2080. 2. Adding fixup for fdt for LS2080. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-06-13armv8: s32v234: Introduce basic support for s32v234evbEddy Petrișor
Add initial support for NXP's S32V234 SoC and S32V234EVB board. The S32V230 family is designed to support computation-intensive applications for image processing. The S32V234, as part of the S32V230 family, is a high-performance automotive processor designed to support safe computation-intensive applications in the area of vision and sensor fusion. Code originally writen by: Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com> Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com> Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com> Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
2016-06-12Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-06-10armv8: ls2080aqds: Enable QSPI boot supportYuan Yao
This patch adds QSPI boot support for LS2080AQDS board. The QSPI boot image need to be programmed into the QSPI flash first. Then we can switch to booting from QSPI memory space. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10armv8: ls2080aqds: Config QSPI pin mux via FPGA in NAND bootYuan Yao
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10armv8: ls2080aqds: disable IFC NOR & QIXIS when QSPI enableYuan Yao
When QSPI is enabled, NOR flash and QIXIS can't be accessed through IFC due to pin mux. Enable I2C QIXIS access and I2C early init to read the sysclk and ddrclk. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10armv8: ls2080aqds: Select QSPI CLK div via SCFGYuan Yao
QSPI module output SCLK divisor value is configured through SCFG. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10board: ls2080a: Add "mcinitcmd" env for MC & DPL deploymentPratiyush Mohan Srivastava
Environment variable mcinitcmd is defined to initiate MC and DPL deployment from the location where it is stored (NOR, NAND, SD, SATA, USB) during booting. If this variable is not defined then macro MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will not be applied during U-boot booting. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-04Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2016-06-04Merge git://git.denx.de/u-boot-nand-flashTom Rini
generated by cgit (git 2.34.1) at 2024-12-26 14:21:27 +0000