| Age | Commit message (Collapse) | Author |
|---|
|
This patch moves the qrio and i2c deblocking code to
keymile/common as it will also be used by the upcoming CENT2 board.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
To acheive this, the qrio_uprstreq() function that sets the UPRSTREQN
flag in the qrio RESCNF reg is added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
To achieve this, the qrio_cpuwd_flag() function that sets the CPU watchdog
flag in the REASON1 reg is added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
This adds the reset support for the following devices that was until
then not implemented:
- BFTIC4
- QSFPs
This also fixes the configuration of the prst behaviour for the other
resets: Only the u-boot and kernel relevant subsystems are taken out of
reset (pcie, ZL30158, and front eth phy).
Most of the prst config move to misc_init_f(), except for the PCIe
related ones that are in pci_init_board and the bftic and ZL30158 ones
that should be done as soon as possible.
Only the behavior of the Hooper reset is changed according to the
documentation as the application is not able to not configure the switch
when it is not reset.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
Add readout of dip-switch to revert to factory settings.
If one or more dip-switch are set, launch bank 0 that contains the
bootloader to do the required action.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
The unit LEDs are managed by the QRIO CPLD. This patch adds support for
accessing these LEDs in the QRIO.
The LEDs then are set to a correct boot state:
- UNIT-LED is red
- BOOT-LED is on.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
|
|
The QRIO GPIO functions can be of general interest. They are thus added
to a qrio.c and their prototype are available from kmp204x.h. The QRIO
prst function are also included in this file, as well as the functions
required for the I2C deblocking support (open-drain).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c]
Signed-off-by: York Sun <yorksun@freescale.com>
|
