summaryrefslogtreecommitdiff
path: root/board/keymile
AgeCommit message (Collapse)Author
2014-02-13arm/km: make local function startup_allowed staticHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: drop unneeded defineHolger Brunck
CONFIG_BOOTCOUNT_LIMIT is used on all boards from this board series. So remove this unneeded define. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-03kmp204x: initial support for PCIe FPGA configurationValentin Longchamp
The PEXHC PCIe configuration mechanism ensures that the FPGA get configured at power-up. Since all the PCIe devices should be configured when the kernel start, u-boot has to take care that the FPGA gets configured also in other reset scenarios, mostly because of possible configuration change. The used mechanism is taken from the km_kirkwood design and adapted to the kmp204x case (slightly different HW and PCIe configuration). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: update I2C field of RCWValentin Longchamp
On the previous HW revision (now unsupported), there was a need for external DMA signals and thus the I2C3/4 signals were used DMA1_DONE/ACK/REQ. These signals now are configured as GPIO[16:19]. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: implement workaround for A-006559Valentin Longchamp
According to the errata, some bits of an undocumented register in the DCSR must be set for every core in order to avoid a possible data or instruction corruption. This is required for the 2.0 revision of the P2041 that should be used as soon as available in our design. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: I2C deblocking supportRainer Boschung
This patch adds support for using some GPIOs that are connected to the I2C bus to force the bus lines state and perform some bus deblocking sequences. The KM common deblocking algorithm from board/keymile/common/common.c is used. The GPIO lines used for deblocking the I2C bus are some external GPIOs provided by the QRIO CPLD: - SCL = GPIOA_20 - SDA = GPIOA_21 The QRIO GPIOs act in an open-drain-like manner, for 0 the line is driven low and for 1 the GPIO is set as input and the line gets pulled-up. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: introduce QRIO GPIO functionsValentin Longchamp
The QRIO GPIO functions can be of general interest. They are thus added to a qrio.c and their prototype are available from kmp204x.h. The QRIO prst function are also included in this file, as well as the functions required for the I2C deblocking support (open-drain). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: support for QRIO1 bootcounterRainer Boschung
Make use of the QRIO1 32bit register at 0x20 as bootcounter register Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Minor change to commit message] Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25Driver/DDR: Moving Freescale DDR driver to a common driverYork Sun
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-17Makefile: make directories by Makefile.buildMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-17Makefile: specifiy an explicite object name rather than $(BOARD).oMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-01board/keymile/kmp204x/Makefile: Convert to SPDX tagTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01board: powerpc: convert more makefiles to Kbuild styleTom Rini
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01board: powerpc: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de>
2013-11-01board: arm: convert makefiles to Kbuild styleMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Tom Rini <trini@ti.com>
2013-10-24mpc85xx: introduce the kmp204x reference design supportValentin Longchamp
This patch introduces the support for Keymile's kmp204x reference design. This design is based on Freescale's P2040/P2041 SoC. The peripherals used by this design are: - DDR3 RAM with SPD support - SPI NOR Flash as boot medium - NAND Flash - 2 PCIe busses (hosts 1 and 3) - 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5) - 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt FPGA - 2 HW I2C busses - last but not least, the mandatory serial port The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb support and was changed according to our design (that means essentially removing what is not present on the designs and a few adaptations). There is currently only one prototype board that is based on this design and this patch also introduces it. The board is called kmlion1. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> kmp204x: update the ENV #define The comments had to be refined as well as the total size Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: fix ddr.c] Acked-by: York Sun <yorksun@freescale.com>
2013-10-24KM: add CONFIG_KM_COMMON_ETH_INIT for km common eth initValentin Longchamp
This must be defined by a board support file that want to use the keymile common.c board_eth_init function that requires ethernet_present to be defined. Currently all the km architectures use it but the kmp204x architecture later supported in this series does use another board_eth_init function and thus does not define it. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2013-10-24KM: define CONFIG_SYS_I2C_INIT_BOARD only for concerned boardValentin Longchamp
This must be defined for all the keymile boards that use the common i2c_abort function that is used to "reset" the I2C bus. These are currently km82xx and km_arm boards. The km83xx boards use other functions and thus do not need this. This patch removes the CONFIG_SYS_I2C_INIT_BOARD from keymile-common.h and defines it for km_arm.h and km82xx.h. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2013-10-14Coding Style cleanup: remove trailing white spaceWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-09km/scripts: fix ramfsAndreas Huber
'actual_bank' is not used anymore, instead boot_bank is used. Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
2013-10-09powerpc/83xx: remove staticness for qe_iop_conf_tabHolger Brunck
commit a5510058 powerpc/83xx/km: make local functions and structs static removed the staticness also from this struct. But this struct is needed in arch/powerpc/cpu/mpc83xx/cpu_init.c and declared as extern. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-10-09Merge branch 'next' of git://git.denx.de/u-boot-mpc83xxTom Rini
2013-07-24Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-07-23i2c, multibus, keymile: get rid of EEprom_ivm envvariableHeiko Schocher
as the keymile boards use now the new i2c multibus/multiadapter framework, remove the EEprom_ivm Environmentvar, as not longer needed. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Holger Brunck <holger.brunck@keymile.com> Tested-By: Holger Brunck <holger.brunck@keymile.com>
2013-07-23i2c, fsl_i2c: switch to new multibus/multiadapter supportHeiko Schocher
- added to fsl_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23i2c, soft-i2c: switch to new multibus/multiadapter supportHeiko Schocher
- added to soft_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-06-10arm/km: make local functions staticHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-05-21powerpc/83xx/km: make local functions and structs staticHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2013-05-21powerpc/83xx/km: MV88e6122 errata fix for 1.9VHolger Brunck
Errata Fix: 1.9V Output from Internal 1.8V Regulator, acc. MV-S300889-00D.pdf , clause 4.5 Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2013-05-10Fix references to the documentation filesAnatolij Gustschin
Many boot image configuration files refer to the appropriate documentation file, but these references contain typos in the directory and file name. Fix them. Also fix reference to doc/README.SPL file. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2013-03-09powerpc/82xx/km: removed unneeded ifdefHolger Brunck
All boards from this serie uses i2c. So we can drop these unneeded defines. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-03-09powerpc/82xx/km: make handle_mgcoge3un_reset staticHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: drop uneeded dtt_bus environment varHolger Brunck
There is no need for a environment variable to configure the dtt bus. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/scripts: replace hardcoded uImageAndreas Huber
Replace uImage with ${uimage}. If uimage is not set, default it to uImage. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: add MV88E6122 switch support for kmvect1Karlheinz Jerg
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection to the switch MV88E6122. This switch has a connection to a frontport ethernet interface. The ethernet port used for network booting is automatically selected by u-boot. If a Piggy is plugged, the Piggy port is selected (UEC2, eth1). If the Piggy isn't present, the Frontport is selected (UEC0, eth0). The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28) and released at startup. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: rework piggy mac adress offset generationHolger Brunck
For the the kmvect1 board we will also need a functionality to add an offset to the IVMs MAC address, because these board will have two valid ethernet ports for debugging purpose. So move the code to an own function. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km82xx, km83xx: move ethernet_present() from common to cpu specificKarlheinz Jerg
For kmvect1 we need a special solution and for km_arm boards we already have. So move the common code to the architectur specific file. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: remove CONFIG_SYS_I2C_IVM_BUS related codeHolger Brunck
This define isn't set within our setup files. So we can safely remove the affected code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: remove obsolete codeHolger Brunck
EEprom_ivm_addr isn't set in our environment, so remove the usage of this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common: remove unneeded ifdefs for I2CHolger Brunck
All boards from this serie use i2c. There is no need to #ifdef the header. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-01-09kirkwood: make MPP arrays static constAlbert ARIBAUD
This saves stack and code memory for local copy, and consumes initialized data memory. For 22 of the 29 kirkwood-based boards, this results in a global saving of about 30 bytes. For 7 of them, it results in an increase of 6 to 14 bytes. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-01-09arm/km: remove duplicate codeValentin Longchamp
This patch removes 2 small portions of board specific code that are duplicated with common ARM code and thus unnecessary. These 2 portions of code concern the mach id that is given by u-boot to the Linux kernel to identify the system's MACH. The first one was the possibility to change the MACH thanks to the 'mach_id' enviroment variable. This is possible thanks to the 'machid' env variable (see arch/arm/lib/bootm.c:boot_jump_linux()). The seconde one is the setting of the bi_arch_number. This is already done in arch/arm/lib/board.c:board_init_f() since km_arm.h does #define CONFIG_MACH_TYPE. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
2013-01-09km/common: cosmetic change reported from checkpatchHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
2013-01-09arm/km: fix memory settingsHolger Brunck
On kmcoge5un we faced some serious problems with the memory during temperature tests. Reason was that we overwrite some registers for memory settings which have to leave untouched. These where registers 0x20148 , 0x2014c and 0x20154. So writing these registers is prohibited and this patch removes them from all km related config files. Even if the problem was only seen on kmcoge5un. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-10-23km83xx: add common support for km8309 boardsGerlando Falauto
Add support for Keymile boards based on mpc8309 (it would be only kmvect1 for now) Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> [#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully] Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-03arm/km: add mv88e6352 configuration for kmnusaValentin Longchamp
The kmnusa board uses a mv88e6352 switch that is connected to the main eth interface of the kirkwood. Therefore the switch must be configured so that the kirkwood's egiga eth inferface can be used. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-10-03arm/km: use kw_sdram_size_adjust to adjust SDRAM sizeHolger Brunck
Some boards may differ only in the SDRAM size. This function allows to fix the size accordingly and we can use the same u-boot binary for both boards. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2012-09-03arm/km: remove unused codeHolger Brunck
For some reasons we had an own implementaion of dram_init and dram_init_banksize. This is not needed anymore, use the standard kirkwood functions instead. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-09-03km/ivm: fix string len check to support 7 char board namesValentin Longchamp
The fanless boards now have a 7-digit (XXXXX-F) board name. This triggers a border condition when reading this string in the IVM although this string is smaller than the currenly read string size, but only by 1 character. This patch corrects this by changing the size check condition for string length. It is the same change that was done in the platform for this same bug. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Stefan Bigler <stefan.bigler@keymile.com>
generated by cgit (git 2.34.1) at 2024-12-28 21:30:15 +0000