summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2015-04-22imx: ventana: updated 16bit DDR calibrationTim Harvey
Updated 16bit DDR calibration using values obtained from running the i.MX6 DDR Stress Test tool over a set of boards over full operationg temperature. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: added DT fixup for GW551x-A video inputTim Harvey
The GW551x-A revision does not have the CSI0_DATA_EN pin connected, therefore we need to make sure that signal is not muxed to the CSI_DATA_EN signal internally and do so by steering it to the unused GPIO5_IO20. We do this so that the kernel device-tree can properly define the signal for RevB and beyond boards that do have this hooked up properly and require it. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: gsc: add new hwmon railsTim Harvey
Add a new voltage rail added in various -C revision PCB's. Additionally make VDD_CORE, VDD_SOC, and VDD_IO2 common as all Ventana boards have those. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: add mem_mb dynamic env varTim Harvey
Certain OS bootscripts need to know how much memory a board has to adjust kernel parameters (namely Android). This allows those boards to determine mem size in MB. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: remove GSC hwmon voltage rail min/max testTim Harvey
The min/max of each depends not only on board but on CPU. Simplify by removing this rarely needed and difficult to maintain feature and just display the rails and their values. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: only pinmux FEC enet signals for boards using itTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: add wdis config for GW5520Tim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: Add support for GW551xTim Harvey
The GW551x is a small form factor board based on the IMX6 SoC that includes: * up to 512MB DDR3 memory * up to 2GB NAND flash * 1x miniPCIe socket (with USB) * HDMI out (micro-HDMI) * HDMI in (micro-HDMI) * TTL level I/O (supported by GW16111 breakout board): * I2C * 2x UART * CAN * 2x DIO (GPIO/PWM) * USB OTG Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: disable IMX6 watchdogs on GW51xx RevA and RevBTim Harvey
A board level errata causes the IMX6 watchdog to be unstable on the GW51xx RevA and RevB boards which can cause the watchdog to trip extremely early (under 5seconds) under certain operating conditions. Disable the watchdog node in the device-tree to work around this issue. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: fix various sparse warningsTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: set LTC3676 PMIC to appropriate values per datasheetTim Harvey
The IMX6 Datasheets specifies that when the IMX6 LDO is enabled (internal Anatop LDO's for VDD_ARM, VDD_SOC, and VDD_xPU) you need to provide 1350mV on VDD_ARM_IN and VDD_SOC_IN for IMX6Q@1GHz (Automotive) and 1275mV for IMX6DL@800MHz (Industrial). While we are still about 50mV shy on the IMX6Q operating at 1GHz we set it to the max we can and leave it up to the kernel to implement a regulator driver for the LTC3676 and put the LDO's in bypass mode which allows us to drop the voltages by 125mV respectively. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: add support for 4Gb density mem devices with IMX6DLTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: enable precharge power-down fast-exit modeTim Harvey
Enable fast-exit precharge mode necessary for some DDR3 devices being used on Ventana boards. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: add usb_pcisel hwconfig supportTim Harvey
The GW52xx has a MUX that can direct front-panel USB OTG to one of the miniPCIe sockets (for use with a cellular modem for example). Use hwconfig to steer this. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: remove unused GPIO configurationTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: assign default ethprime dynamicallyTim Harvey
Gateworks Ventana boards don't all use IMX6 FEC, so lets define default ethprime based off the first detected device. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: add i210 supportTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22mx6: Add initial SPL support for HummingBoard-i2eXFabio Estevam
Add the initial SPL support for HummingBoard-i2eX, which is based on a MX6 Dual. For more information about HummingBoard, please check: http://www.solid-run.com/products/hummingboard/ Based on the work from Jon Nettleton and Rabeeh Khoury. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-13Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-04-13ARM: rpi: add a couple more revision IDsStephen Warren
According to Gordon Henderson's WiringPi library, there are some more Pi revision IDs out there. Add support for them. http://git.drogon.net/?p=wiringPi;a=blob_plain;f=wiringPi/wiringPi.c;hb=5edd177112c99416f68ba3e8c6c4db6ed942e796 At least ID 0x13 is out in the wild: Reported-by: Chee-Yang Chau <cychau@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-10Merge git://git.denx.de/u-boot-arcTom Rini
2015-04-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2015-04-10lpc32xx: add support for board work_92105Albert ARIBAUD \(3ADEV\)
Work_92105 from Work Microwave is an LPC3250- based board with the following features: - 64MB or 128MB SDR DRAM - 1 GB SLC NAND, managed through MLC controller. - Ethernet - Ethernet + PHY SMSC8710 - I2C: - EEPROM (24M01-compatible) - RTC (DS1374-compatible) - Temperature sensor (DS620) - DACs (2 x MAX518) - SPI (through SSP interface) - Port expander MAX6957 - LCD display (HD44780-compatible), controlled through the port expander and DACs This board has SPL support, and uses the LPC32XX boot image format. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-09odroid-XU3: update board maintainerPrzemyslaw Marczak
At present Hyungwon can't take care of this board in U-Boot, so I will keep it working. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Hyungwon Hwang <human.hwang@samsung.com>
2015-04-09mcx: update maintainer and convert to generic boardAnatolij Gustschin
Remove obsolete email address from MAINTAINERS. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tom Rini <trini@konsulko.com>
2015-04-09board: axs10x - support v3 mother-boardAlexey Brodkin
There're 2 versions of motherboards that could be used in ARC SDP. The only important difference for U-Boot is different NAND IC in use: [1] v2 board (we used to support up until now) sports MT29F4G08ABADAWP while [2] v3 board sports MT29F4G16ABADAWP They are almost the same except data bus width 8-bit in [1] and 16-bit in [2]. And for proper support of 16-bit data bus we have to pass NAND_BUSWIDTH_16 option to NAND driver core - which we do now knowing board type we're running on. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-04-09ARM: mx5: add support for USB armory boardAndrej Rosano
Add support for Inverse Path USB armory board, an open source flash-drive sized computer based on Freescale i.MX53 SoC. http://inversepath.com/usbarmory Signed-off-by: Andrej Rosano <andrej@inversepath.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Chris Kuethe <chris.kuethe@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Vagrant Cascadian <vagrant@debian.org> Tested-By: Vagrant Cascadian <vagrant@debian.org> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
2015-04-08ARM: zynq: Remove Jagan from list of maintainersMichal Simek
Email address is not longer valid that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-08mx53loco: Disable printing cpuinfoFabio Estevam
Since commit 32df39c741788e ("mx5: fix get_reset_cause") we have the following boot messages on a mx53qsb: U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: POR Board: MX53 LOCO I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial CPU: Freescale i.MX53 rev2.1 at 1000 MHz Reset cause: unknown reset Net: FEC [PRIME] The CPU and Reset cause lines appear twice. Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via I2C to raise the CPU voltage so that it can run at 1GHz. To avoid such misleading double printings, disable printing cpu info for now. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2015-04-06smdk5420: Remove GPIO enumsAjay Kumar
Remove GPIOs from smdk5420 board file and because the same is already specified via DT. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-04-03Merge git://git.denx.de/u-boot-arcTom Rini
2015-04-03Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
Conflicts: board/armltd/vexpress64/vexpress64.c Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-03board: AXS10x - update SDIO clock valueAlexey Brodkin
With the most recent board firmware correct SDIO clock is 50MHz as opposed to 25 MHz before. Also set max frequency of MMC data exchange equal to SDIO clock - because there's no way to transfer data faster than interface clock. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-03-31Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2015-04-01ARM: atmel: at91sam9n12ek: enable spl supportBo Shen
Enable SPL support for at91sam9n12ek boards, now it supports boot up from NAND flash, serial flash. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-04-01ARM: atmel: at91sam9x5ek: enable spl supportBo Shen
Enable SPL support for at91sam9x5ek board. Now, it supports boot up from NAND flash and SPI flash. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-04-01ARM: atmel: at91sam9m10g45ek: enable spl supportBo Shen
Supports boot up from NAND flash with software ECC eanbled. And supports boot up from SD/MMC card with FAT file system. As the boot from SD/MMC card with FAT file system, the BSS segment is too big to fit into SRAM, so, use the lds to put it into SDRAM. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-04-01ARM: at91: sama5d4: display the U-Boot version on LCDWu, Josh
This patch will display the U-Boot version on LCD. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Bo Shen <voice.shen@atmel.com>
2015-03-31Merge git://git.denx.de/u-boot-nand-flashTom Rini
2015-03-31Merge branch 'master' of git://git.denx.de/u-boot-imxTom Rini
2015-03-30nand: Remove CONFIG_MTD_NAND_VERIFY_WRITEPeter Tyser
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some time and a more generic method of NAND verification now exists in U-Boot. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
2015-03-30ARM: tegra: colibri_t20: fix nand pinmuxMarcel Ziswiler
Pingroup ATC seems to come out of reset with config set to NAND, so we need to explicitly configure some other function to this group in order to avoid clashing settings. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-30ARM: tegra: fix colibri_t20 asix resetMarcel Ziswiler
Fix ASIX USB to Ethernet chip reset. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-30ARM: tegra: rename colibri_t20 board/configuration/device-treeMarcel Ziswiler
In accordance with our other modules supported by U-Boot and as agreed upon for Apalis/Colibri T30 get rid of the carrier board in the board/ configuration/device-tree naming. While at it also bring the prompt more in line with our other products. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-30ARM: tegra: get rid of colibri_t20-commonMarcel Ziswiler
As a preparatory step to renaming the board folder as well first get rid of the colibri_t20-common after having integrated it into colibri_t20_iris for now. While at it also migrate to using NVIDIA's common.mk magic. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-30tegra: seaboard: Correct the gpio_request() callSimon Glass
Requesting a GPIO without a name is not supposed anymore. This causes the request to fail. Add a name so that the serial console works on seaboard. Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-29sunxi: UTOO_P66: Add missing MAINTAINERS entryHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29sunxi: use CONFIG_SYS_CLK_FREQ to set cpu clockIain Paton
make the CPU clock selectable via Kconfig this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each soc header and replaces it's use in board/sunxi/board.c with CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board specific frequency on boot Signed-off-by: Iain Paton <ipaton0@gmail.com> [hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the arch-timer clk speed on sun7i to fix mis-compile on sun7i] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-28powerpc: ppc4xx: convert AMCC boards to generic boardAnatolij Gustschin
Add CONFIG_SYS_GENERIC_BOARD to amcc-common.h and CONFIG_DISPLAY_BOARDINFO to Kconfig files. canyonlands.h includes amcc-common.h, so remove CONFIG_SYS_GENERIC_BOARD definition there. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Feng Kan <fkan@amcc.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tom Rini <trini@konsulko.com>
2015-03-28m68k: fix 3 broken boardsangelo@sysam.it
Fix eb_cpu5282 and eb_cpu5282_internal unresolved external error. These boards have video but don't need any ppc related video_setmem(). Fix M53017EVB moving away embedded env to a different offset, as in M52277EVB. Signed-off-by: Angelo Dureghello <angelo@sysam.it>
generated by cgit (git 2.34.1) at 2025-01-27 06:00:04 +0000