summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2020-01-07board: ge: bx50v3: Fix run-time warningIan Ray
Fix GPIO reservation warning on code paths that do not need LVDS power. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07board: ge: bx50v3: sync devicetrees from LinuxRobert Beckett
Copy device trees from linux, keeping them as separate files for each board to ease future sync. Update board code to use generic bx50v3 dt initially, then select the specific dt based on board detection. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-07imx: Add support for i.MX28 based XEA boardLukasz Majewski
This patch introduces support for i.MX28 based XEA board. This board supports DM/DTS in U-Boot proper as well as DM aware drivers in SPL (u-boot.sb) by using OF_PLATDATA. More detailed information regarding usage of it can be found in ./board/liebherr/xea/README file. U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200) Trying to boot from MMC1 MMC0: Command 8 timeout (status 0xf0344020) mmc_load_image_raw_sector: mmc block read error U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200) CPU: Freescale i.MX28 rev1.2 at 454 MHz BOOT: SSP SPI #3, master, 3V3 NOR Model: Liebherr (LWE) XEA i.MX28 Board DRAM: 128 MiB MMC: MXS MMC: 0 Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB OK In: serial Out: serial Err: serial Net: Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2 eth0: ethernet@800f0000 Hit any key to stop autoboot: 0 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-01-07imx6: aristainetos: add support for rev C boardHeiko Schocher
add support for revision C boards. This board has no longer a NAND. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add aristainetos 2b cslHeiko Schocher
add aristainetso board version CSL. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: readd aristainetos 2b boardHeiko Schocher
readd aristainetos 2b board. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: enable HAB bootHeiko Schocher
enable IMX_HAB on aristianetos board Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: cleanup bootmode settingsHeiko Schocher
on the aristainetos there are some jumpers for changing behaviour setting up Environment. Clean this up. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add i2c eeprom supportHeiko Schocher
add support for i2c eeprom and add parsing "Rescue" or "DefEnv" at offset 0x1ff0. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: get rid of CONFIG_BOARDNAMEHeiko Schocher
CONFIG_BOARDNAME is not longer needed, as we use the model information from DTS. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: convert to DM_PWM/DM_BACKLIGHTHeiko Schocher
use DM_PWM and DM_BLACKLIGHT support and remove board code. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add DM_I2C supportHeiko Schocher
enable DM_I2C in defconfig and remove i2c specific board code. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add DM_VIDEO supportHeiko Schocher
add DM_VIDEO support and remove now unneeded board code. As we show a bmp logo on boot, call now bmp_display() from board code and do not use cfb_console anymore. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: enable DM_ETHHeiko Schocher
enable DM_ETH and remove unneeded board code. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: convert CONFIG_DM_SPIHeiko Schocher
enable CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH and get rid of build removal warnings. define CONFIG_GPIO_ENABLE_SPI_FLASH is not longer needed, so remove it from config_whitelist.txt Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: convert to DM_USBHeiko Schocher
Drop CONFIG_USB_MAX_CONTROLLER_COUNT and enable DM_USB in defconfig. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: convert gpio pins to DM and DTSHeiko Schocher
Enable DM_GPIO, GPIO_HOG, LED and LED_GPIO as gpio and LEDs are now defined in DTS. Enable also here the pinctrl driver, so pinmux setup is also done. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: convert to DM_MMCHeiko Schocher
Enable DM_MMC support. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add DM_SERIAL supportHeiko Schocher
add DM_SERIAL support for the aristainetos board, and remove not used code from board code. remove CONSOLE_OVERWRITE_ROUTINE. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: prepare dts for other board versionsHeiko Schocher
as we switch to support DM and DTS, rework the existing DTS trees. Change also Linux specific Device trees, goal is to push this changes to linux. Collect U-Boot specific changes in separate "*u-boot*" dts files. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: remove aristainetos-v2.cHeiko Schocher
remove aristainetos-v2.c file, as we now want to switch to DM/DTS support and have all board specific code in one file. Goal is to setup differences through DT. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: add device tree from linuxHeiko Schocher
Add device trees from Linux in preparation for driver model conversions. device tree files taken from Linux: 71ae5fc87c34: "Merge tag 'linux-kselftest-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest" and added SPDX license identifier. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: remove 2b versionHeiko Schocher
remove 2b version of aristainetos board, as it is easier to make the DM / DTS port and introduce the 2b board version again (also some more board version). Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: aristainetos: move defines to KconfigHeiko Schocher
move defines, which are already moved to Kconfig out of board config. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-07imx6: remove aristainetos boardHeiko Schocher
remove not anymore used aristainetos board. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-01-06Merge branch 'next'Tom Rini
Bring in the following merges: commit 8fbbec12f7d2c18f8883f3371cfca74a98b5dd87 Merge: 87f69f467a83 63618e71e89b Author: Tom Rini <trini@konsulko.com> Date: Fri Jan 3 09:48:47 2020 -0500 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next - updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support commit 87f69f467a8335b171c71bf217d2625d515acd7c Merge: c0912f9bbfb2 4466b9970319 Author: Tom Rini <trini@konsulko.com> Date: Tue Dec 24 08:18:19 2019 -0500 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next - Enable DM driver on ppc/km boards - Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x, T104x, P4080, P2041, P2020, P1020, P3041 - Some updates in mpc85xx-ddr driver, km boards commit c0912f9bbfb26dd03d189953678691b799d35b6e Merge: 533c9f5714bd a1d6dc3f8407 Author: Tom Rini <trini@konsulko.com> Date: Wed Dec 18 07:20:19 2019 -0500 Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next - Various x86 common codes updated for TPL/SPL - I2C designware driver updated for PCI - ICH SPI driver updated to support Apollo Lake - Add Intel FSP2 base support - Intel Apollo Lake platform specific drivers support - Add a new board Google Chromebook Coral commit 533c9f5714bdba79dc6f2629284d4c1a08a611d1 Merge: 553cb0688782 033e18b47bd0 Author: Tom Rini <trini@konsulko.com> Date: Tue Dec 17 07:53:08 2019 -0500 Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next i2c: for next - misc: i2c_eeprom: Add partition support and add ability to query size of eeprom device and partitions - i2c common: add support for offset overflow in to address and add sandbox tests for it. commit 553cb06887825314e74a9bdac337467c77d1db88 Merge: f39abbbc531e b4f98b3b16ec Author: Tom Rini <trini@konsulko.com> Date: Thu Dec 12 08:18:59 2019 -0500 Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next buildman improvements including toolchain environment feature sandbox unicode support in serial
2019-12-28Merge tag 'u-boot-imx-20191228' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.01 ----------------- - Fixes for Nitrogen6x - Fix corruption for mx51evk - colibri i.MX6: fix broken ESDHC conversion - mx6sxsabresd: fix broken mmcdev - imx6q_logic: cleanup boot sequence - update ATF for imx8mq_evk - pfuze: fix pmic_get() Travis CI: https://travis-ci.org/sbabic/u-boot-imx/builds/630007464
2019-12-27Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- Orange Pi Zero Plus 2 support - sunxi psci, prcm fixes
2019-12-27ARM: imx6q_logic: Cleanup boot sequence checkAdam Ford
The board_boot_order() function currenly assumes that the boot source is MMC/eMMC, but this isn't true for the NAND devices. This patch cleans up board_boot_order() to check for NAND, SD, ESD, MMC or EMMC. Anything beyond these are not supported, so it will default back to the serial downloader if any of those devices are not available. Fixes: 9fb50c68daa6 ("ARM: imx6q_logic: Fix MMC2 booting") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-12-27nitrogen6x: prepare for CONFIG_MX6QDLTroy Kisky
The next patch adds CONFIG_MX6QDL so that errata will be enabled again. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-12-27imx8mq_evk: Update the required ATF branchFabio Estevam
Following the README instructions leads to a non-booting U-Boot: U-Boot SPL 2020.01-rc3-00070-g9a0cbae22a (Nov 25 2019 - 13:08:24 -0300) PMIC: PFUZE100 ID=0x10 DDRINFO: start DRAM init DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done Normal Boot Trying to boot from MMC2 (It hangs here) Use the "imx_4.19.35_1.0.0" ATF branch instead, which fixes such problem and allow the boot to complete again. Suggested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-12-27pfuze: Fix the pmic_get() parameter in the DM caseFabio Estevam
Currently the following hang is observed when booting a imx6sx-sdb board: U-Boot 2020.01-rc5-00004-g643366bcd5 (Dec 19 2019 - 14:56:23 -0300) CPU: Freescale i.MX6SX rev1.0 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 32C Reset cause: POR Model: Freescale i.MX6 SoloX SDB RevB Board Board: MX6SX SABRE SDB revA DRAM: 1 GiB initcall sequence bffd8514 failed at call 87804cc0 (err=-19) ### ERROR ### Please RESET the board ### When pmic_get() is used with DM the first parameter must be the complete node name plus the unit address. Fix the pmic_get() parameter to fix the boot regression. Tested on a imx6sx-sdb and imx6q-sabresd boards. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-12-27colibri_imx6: fix broken fsl_esdhc_imx conversionIgor Opaniuk
Not all CONFIG_FSL_ESDHC defines were properly replaced with CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on Colibri iMX6 SoMs. U-boot is stuck after this message: Commercial temperature grade DDR3 timings, 64bit bus width. Trying to boot from MMC1 Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-12-26board: davinci: Update OMAPL138_LCDK maintainerLokesh Vutla
As per the email discussion[0], add myself as a maintainer to OMAPL138_LCDK and drop Peter's entry. [0] http://u-boot.10912.n7.nabble.com/OMAP-L138-LCDK-giving-up-maintainership-td394211.html Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-12-26armv8: ls1028ardb: enable DisplayPort Power supportWen He
Enable DP_PWR signal to power the DP to HDMI converter cable. Signed-off-by: Wen He <wen.he_1@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26armv8: ls1046afrwy: Fix get_board_version implementationPramod Kumar
Current implementation to get board version through GPIO is broken due to endianness issue hence it is not working for rev B board. Fix it to make it work for Rev A as well as Rev B boards Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-23board/km: remove CONFIG_KM_BOARD_NAMEHolger Brunck
We can use the existing CONFIG_SYS_CONFIG_NAME define for that and remove the option. Also fix the boot string for all km83xx boards. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> CC: Priyanka Jain <priyanka.jain@nxp.com> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
2019-12-23ppc/km: convert KM_DEF_NETDEV to KconfigHolger Brunck
Remove this from the board header files and move it to Kconfig. Also use the correct default address for kmtegr1. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> CC: Priyanka Jain <priyanka.jain@nxp.com> CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
2019-12-18sun8i: h3: Support H3 variant of Orange Pi Zero Plus 2Diego Rondini
Orangepi Zero Plus 2 is an open-source single-board computer, available in two Allwinner SOC variants, H3 and H5. We add support for H3 variant here, as the H5 is already supported. H3 Orangepi Zero Plus 2 has: - Quad-core Cortex-A7 - 512MB DDR3 - microSD slot and 8GB eMMC - Debug TTL UART - HDMI - Wifi + BT - OTG + power supply Sync dts from linux v5.2 commit: "ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry" (sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b) Commit: "ARM: dts: sun8i: h3: Refactor the pinctrl node names" (sha1: a4dc791974e568a15f7f37131729b1a6912f4811) has been avoided as it breaks U-Boot build. Signed-off-by: Diego Rondini <diego.rondini@kynetics.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-12-17board: atmel: sama5d27_wlsom1_ek: Set ethaddr from spi-nor flashTudor Ambarus
The SST26VF064BEUI spi-nor flash is programmed at the factory with a globally unique address stored in the SFDP vendor parameter table and it is permanently writeprotected. Retrieve the EUI-48 address and set it as ethaddr env. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2019-12-15x86: Add chromebook_coralSimon Glass
Add support for coral which is a range of Apollo Lake-based Chromebook released in 2017. This also includes reef released in 2016, since it is based on the same SoC. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-15dm: gpio: Allow control of GPIO uclass in SPLSimon Glass
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass is included in SPL/TPL without any control for boards. Some boards may want to disable this to reduce code size where GPIOs are not needed in SPL or TPL. Add a new Kconfig option to permit this. Default it to 'y' so that existing boards work correctly. Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to preserve the current behaviour. Also update the 74x164 GPIO driver since it cannot build with SPL. This allows us to remove the hacks in config_uncmd_spl.h and Makefile.uncmd_spl (eventually those files should be removed). Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-12-11Merge tag 'rpi-next-2020.01.2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi - fix DRAM bank detection for unified binary - fix 32bit RPi4 config
2019-12-11Merge tag 'u-boot-atmel-fixes-2020.01-a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel - First set of u-boot-atmel fixes for 2020.01 cycle: This set includes a small fix for gpio bank names, one for removing unused headers (also touches some other boards), and a fix for the QSPI env read on one of the boards.
2019-12-11rpi: Enable DRAM bank initialization on arm64Matthias Brugger
Up to now we only update the DRAM banks when we are define CONFIG_BCM2711. But our one binary approach uses a config that supports BCM2837 and BCM2711. As a result we only see one gibibyte of RAM on Raspberry Pi 4, even if it has more RAM. Fix this by calling dram_init_banksize. Fixes: 5694090670 ("ARM: defconfig: add unified config for RPi3 and RPi4") Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-12-11rpi: fix dram bank initializationMatthias Brugger
To update the dram bank information from device-tree we use fdtdec_decode_ram_size() which expectes the the size-cells and address-cells to be defined in the memory node. For normal system RAM these values are defined in the root node. When the values differ from the default values defined in the spec, we can end up with wrong RAM bank information. Switch to the "standard" way to update the RAM bank information to avoid this. Fixes: 9de5b89e4c ("rpi4: enable dram bank initialization") Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-12-09Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Increase stack size to avoid a stack overflow during distro boot. - Add hifive-unleashed-a00.dts for SIFIVE FU540. - Add OF_SEPARATE support for SIFIVE FU540. - Add SPL support for Andes AX25 AE350. - Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
2019-12-10riscv: ax25-ae350: Use generic memory size setupRick Chen
To get memory size from device tree instead of get_ram_size(). This can avoid memory access fault in U-Boot proper after PMP configurations in OpenSBI. Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Cc: Alan Kao <alankao@andestech.com>
2019-12-10riscv: ax25-ae350: add SPL configurationRick Chen
This patch provides four configurations which can support U-Boot SPL to boot from RAM or FLASH and then boot FIT image including OpenSBI FW_DYNAMIC firmware and U-Boot proper images from RAM or MMC boot devices. With ae350_rv[32|64]_spl_defconfigs: U-Boot SPL will be loaded by gdb or FSBL and runs in RAM in machine mode and then load FIT image from RAM device on AE350. With ae350_rv[32|64]_spl_xip_defconfigs: U-Boot SPL can be burned into SPI flash and run in flash in machine mode and then load FIT image from SPI flash or MMC device on AE350. Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Cc: Alan Kao <alankao@andestech.com>
2019-12-09Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-netTom Rini
generated by cgit (git 2.34.1) at 2025-01-10 21:44:13 +0000