summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-04-13apalis_imx6: drop CONFIG_OF_SYSTEM_SETUPMarcel Ziswiler
This doesn't do anything anymore, probably never did. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13apalis_imx6: migrate usb to using driver modelMarcel Ziswiler
Migrate USB to using driver model. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13apalis_imx6: migrate mmc and sata to using driver modelMarcel Ziswiler
Migrate MMC and SATA to using driver model. While at it also enable SCSI driver model. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13apalis_imx6: migrate i2c to using driver modelMarcel Ziswiler
Migrate I2C to using driver model. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13apalis_imx6: clean-up and migrate gpios to using driver modelMarcel Ziswiler
Migrate GPIOs to using driver model, properly request backlight, Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also enable SION bit in pin muxing for Apalis, backlight, eMMC reset, Ethernet PHY reset and USB power enable GPIOs. While at it also update copyright year, clean-up/re-order includes, add some comments clarifying ifdef scope and do some White-space clean-up. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13apalis_imx6: migrate to using device treeMarcel Ziswiler
Migrate to using device tree required for further driver model integration. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13apalis_imx6: get rid of obsolete nospl configurationsMarcel Ziswiler
Now with SPL long since being in place even for recovery using SDP finally get rid of those nospl configurations. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13mx53ppd: bring dock out of reset at bootIan Ray
Configure GPIO BUFFERED_HOST_CONTROLLED_RESET_TO_DOCKING_CONNECTOR_N to bring the dock out of reset at boot. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13board: ge: store version information in fdtIan Ray
Add board-specific FDT function to store U-Boot version in device tree. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13board: ge: ppd: Enable CONFIG_DM_MMCIan Ray
Use MMC device model, and remove USDHC pin configuration code since the pinctrl driver is used. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13board: ge: bx50v3: Enable CONFIG_DM_SPI, CONFIG_DM_SPI_FLASHIan Ray
Use SPI flash device model, and remove SPI pin configuration code since the pinctrl driver is used. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13board: ge: bx50v3: Enable CONFIG_DM_GPIOIan Ray
Enable CONFIG_DM_GPIO as a pre-requisite for enabling CONFIG_DM_SPI. Add explicit gpio_requests. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13board: ge: bx50v3: Enable CONFIG_DM_MMCIan Ray
Use MMC device model, and remove USDHC pin configuration code since the pinctrl driver is used. Signed-off-by: Ian Ray <ian.ray@ge.com>
2019-04-13pcm052: bk4: Add board_phy_config() for BK4 to setup ksz8081 phyLukasz Majewski
BK4 requires setup of 50MHz reference clock for its KSZ8081 PHY devices. Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-13pcm052: mac: Provide board specific imx_get_mac_from_fuse() functionLukasz Majewski
This commit introduces the board specific function to read fused mac address. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Add code to setup LED default statesLukasz Majewski
As one has moved to DM based LEDs, this code is required to setup the default state. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: bk4: sdcard: Add support for SD card booting/recoveryLukasz Majewski
This code allows reusing the default u-boot as in the late board init, the default envs are restored and proper recovery scripts executed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Remove in-board setup code (it is now replaced by DM setup)Lukasz Majewski
This commit cleans up the pcm052.c file to remove dead code after moving to DTS and DM. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: cosmetic: Add copyright notice to pcm052.cLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: vybrid: Update the board name for BK4 deviceLukasz Majewski
This commit provides distinction between PCM052 and BK4. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Remove "m4go" command as it is superseded by "bootaux"Lukasz Majewski
The "m4go" provides exactly the same functionality as the IMX generic "bootaux" command. Remove it to not duplicate the code. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-13pcm052: board: Do not enable I2C2 code in the board fileLukasz Majewski
As the I2C2 clock is now enabled in the generic clock code, we can remove this code from a board file. Signed-off-by: Lukasz Majewski <lukma@denx.de> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-12Merge tag 'u-boot-stm32-20190412' of https://github.com/patrickdelaunay/u-bootTom Rini
stm32 patches for v2019.07-rc1 - Add trusted boot with TF-A for stm32mp1 - stm32mp1 dts files sync'ed with Linux version - add STM32MP1 Discovery boards (DK1 and DK2) - add STMFX gpio expander driver - misc improvement for stm3mp1 supports - rename stpmu1 to stpmic1 (official name) - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu) - add STM32 FMC2 NAND flash controller driver
2019-04-12Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-04-12Merge git://git.denx.de/u-boot-marvellTom Rini
- Misc dts files sync'ed with Linux version (Chris) - Orion watchdog fix (Chris) - kwbimage changed to also support Marvell bin_hdr binary (Chris) - Add DM support to enable CONFIG_BLK for sata_mv (Stefan) - Enable BLK on multiple platforms (Stefan) - Misc minor fixes to AXP theadorable board (Stefan) - Correct logic for DM_SCSI + unconverted drivers check (stefan) - Misc changes to kirkwood to enable DM_USB here (Chris) - Change ahci_mvebu to enable usage on A38x (Baruch) - Update the kirkwood entry in git-mailrc (Baruch) - Misc minor improvements (turris, documentation) (Baruch) - Enhance sata_mv to support Kirkwood as well (Michael) - Add wdt command (Michael) - Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG board support (Chris)
2019-04-12board: stm32mp1: Force pinctrl driver probe in board_init()Patrice Chotard
In order to insure that hog GPIOs are configured early during the boot process, force all pinctrl driver probing in board_init(). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12Board: stm32mp1: Add supply current boot informationPatrice Chotard
For DK1/DK2 boards, check if power supply provides enough current to allow the board to boot correctly. ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2 signals. The table below shows the behavior for different range of CC1 or CC2: range | power supply | red led | console message (Volts) | (Amps) | blinks | --------------|--------------|---------|----------------------------------- [2.10 - 1.23[ | 3 | NO | NO [1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected [0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected If detected current is < 3A, red led is kept ON after blinking. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12board: stm32mp1: Update README filePatrice Chotard
Update README with DK1 and DK2 boards related informations Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12stpmic1: update register namesPatrick Delaunay
Alignment with STPMIC1 datasheet s/MAIN_CONTROL_REG/MAIN_CR/g s/MASK_RESET_BUCK/BUCKS_MRST_CR/g s/MASK_RESET_LDOS/LDOS_MRST_CR/g s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g s/VREF_CTRL_REG/REFDDR_MAIN_CR/g s/LDOX_CTRL_REG/LDOX_MAIN_CR/g s/USB_CTRL_REG/BST_SW_CR/g s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g and update all the associated defines. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12power: rename stpmu1 to official name stpmic1Patrick Delaunay
Alignment with kernel driver name & binding introduced by https://patchwork.kernel.org/cover/10761943/ to use the final marketing name = STPMIC1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12power: stpmu1: rename files to stpmic1Patrick Delaunay
Prepare file modification for kernel alignment and rename driver to stpmic1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12stm32mp1: add syscfg initializationPatrick Delaunay
Initialize the system configuration for basic boot - update interconnect setting - disable pull-down for boot pin - enable High Speed Low Voltage Pad mode for SPI, SDMMC, ETH, QSPI - activate I/O compensation Done by SSBL = TF-A for trusted boot Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: support forced boot modePatrick Delaunay
The boot mode can be forced by key press or by TAMP register, requested in kernel by syscon-reboot-mode tamp: tamp@5c00a000 { compatible = "simple-bus", "syscon", "simple-mfd"; reg = <0x5c00a000 0x400>; reboot-mode { compatible = "syscon-reboot-mode"; offset = <0x150>; /* reg20 */ mask = <0xff>; mode-normal = <0>; mode-fastboot = <0x1>; mode-recovery = <0x2>; mode-stm32cubeprogrammer = <0x3>; mode-ums_mmc0 = <0x10>; mode-ums_mmc1 = <0x11>; mode-ums_mmc2 = <0x12>; }; }; Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update bootcmdPatrick Delaunay
Clearly separate bootcmd for stm32mp1 board (bootcmd_stm32mp) and preboot management. That solve issue for fastboot continue command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add runtime information in environmentPatrick Delaunay
Set board name with the first dts compatible found in DT code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG The result with DEVICE_TREE=stm32mp157c-ev1 is: STM32MP> env print board=stm32mp1 board_name=stm32mp157c-ev1 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: display board informationPatrick Delaunay
Implement checkboard() function to display - the boot chain used: basic or trusted - the board compatible in device tree - the board identifier and revision, saved in OTP59 for ST boards Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add trusted boot with TF-APatrick Delaunay
Add support of trusted boot, using TF-A as first stage bootloader, The boot sequence is BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32 The TF-A monitor provides secure monitor with support of SMC - proprietary to manage secure devices (BSEC for example) - PSCI for power The same device tree is used for STMicroelectronics boards with basic boot and with trusted boot. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12ARM: am3517_evm: Add spl_start_uboot for Falcon ModeAdam Ford
When booting the am3517-evm, the following message appears: SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! This patch implements spl_start_uboot to clear this message and allow device to know if it should boot U-Boot or kernel. Fixes: 1c6b6f383a41 ("ARM: am3517_evm: Enable Falcon Mode") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12board: ti: am335x: Remove non DM_ETH codeFaiz Abbas
With DM_ETH enabled in am335x devices, remove all the unused non-DM code. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12board: ti: am335x: Add platdata for cpsw in SPLFaiz Abbas
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL is enabled. Use static platdata instead to save space. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12board: ti: am65x: Enable fixing up msmc sram nodeLokesh Vutla
Create a ft_board_setup() api that gets called as part of DT fixup before jumping to kernel. In this ft_board_setup() call fdt_fixup_msmc_ram that update msmc sram node. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-12arm: dra7: Allow NAND to be enabled on DRA71x EVM.Franklin S Cooper Jr
If SW 8 pins 0 and 1 indicate that NAND should be enabled then the pins pinmux must be reconfigured for NAND mode. Therefore, enable NAND by reconfiguring the pinmux. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12board: ti: dra71: Add pinmux settings for NAND on DRA71x EVMFranklin S Cooper Jr
By default VOUT3 occupies the pins required for NAND. Therefore, create a seperate entry that can be use to reconfigure these pins to work for NAND. On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is enabled or not. For NAND to be selected pin 0 should be on and pin 1 should be off. Any other combination will assume NAND shouldn't be enabled. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12ARM: davinci: da850evm: Enable SPL_OF_CONTROL without PLATDATAAdam Ford
With the memory mapping giving us some more avialable RAM, this updates the da850-evm-u-boot.dtsi to include the serial port, SPI and Flash nodes along with some dependent nodes in the SPL dtb. This also removes the platform data initialization code for the serial port and SPI Flash. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12davinci: da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is fullAdam Ford
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit larger. This patch relocates BSS to SDRAM instead of SRAM which is similar to how ARMv7 boards (like OMAP2+) do it. This means two new variables are required: CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte before the location where U-Boot will load. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12am335x, guardian: Add support for the bosch guardian boardSjoerd Simons
Add support for the Bosch Guardian board. CPU : AM335X-GP rev 2.1 Model: Bosch AM335x Guardian I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Felix Brack <fb@ltec.ch>
2019-04-12ARM: k2g: add a workaround to reset the phyMurali Karicheri
This patch adds a workaround to reset the phy one time during boot using GPIO0 pin 10 to make sure, the Phy latches the configuration from the input pins correctly. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-12ARM: k2g-gp-evm: update to rgmii pinmux configurationMurali Karicheri
This patch updates pinmux configuration for K2G GP EVM based on data generated by the pinmux tool at https://dev.ti.com/pinmux/app.html#/default Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-12ARM: k2g-ice: Add pinmux support for rgmii interfaceMurali Karicheri
This add pinmux configuration for rgmii interface so that network driver can be supported on K2G ICE boards. The pinmux configurations for this are generated using the pinmux tool at https://dev.ti.com/pinmux/app.html#/default As this required some BUFFER_CLASS definitions, same is re-used from the linux defnitions in include/dt-bindings/pinctrl/keystone.h Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-12arm: mvebu: Add DB-XC3-24G4XG boardChris Packham
The DB-XC3-24G4XG is a switch development board from Marvell. It can either use and external CPU card such as the db-88f6820-amc or the internal CPU that is integrated into the switch. Add support for running U-Boot on the internal CPU and enable the USB, SPI and NAND peripherals. For now this needs the bin_hdr from the Marvell U-Boot for this board. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit (git 2.34.1) at 2025-02-12 07:02:27 +0000