summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2014-02-03kmp204x: initial support for PCIe FPGA configurationValentin Longchamp
The PEXHC PCIe configuration mechanism ensures that the FPGA get configured at power-up. Since all the PCIe devices should be configured when the kernel start, u-boot has to take care that the FPGA gets configured also in other reset scenarios, mostly because of possible configuration change. The used mechanism is taken from the km_kirkwood design and adapted to the kmp204x case (slightly different HW and PCIe configuration). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: update I2C field of RCWValentin Longchamp
On the previous HW revision (now unsupported), there was a need for external DMA signals and thus the I2C3/4 signals were used DMA1_DONE/ACK/REQ. These signals now are configured as GPIO[16:19]. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: implement workaround for A-006559Valentin Longchamp
According to the errata, some bits of an undocumented register in the DCSR must be set for every core in order to avoid a possible data or instruction corruption. This is required for the 2.0 revision of the P2041 that should be used as soon as available in our design. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: I2C deblocking supportRainer Boschung
This patch adds support for using some GPIOs that are connected to the I2C bus to force the bus lines state and perform some bus deblocking sequences. The KM common deblocking algorithm from board/keymile/common/common.c is used. The GPIO lines used for deblocking the I2C bus are some external GPIOs provided by the QRIO CPLD: - SCL = GPIOA_20 - SDA = GPIOA_21 The QRIO GPIOs act in an open-drain-like manner, for 0 the line is driven low and for 1 the GPIO is set as input and the line gets pulled-up. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: introduce QRIO GPIO functionsValentin Longchamp
The QRIO GPIO functions can be of general interest. They are thus added to a qrio.c and their prototype are available from kmp204x.h. The QRIO prst function are also included in this file, as well as the functions required for the I2C deblocking support (open-drain). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: support for QRIO1 bootcounterRainer Boschung
Make use of the QRIO1 32bit register at 0x20 as bootcounter register Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Minor change to commit message] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03powerpc/t104xrdb: Add basic ethernet supportPriyanka Jain
This covers only non-L2 switch ethernet interfaces i.e. RGMII and SGMII interface for both T1040RDB and T1042RDB_PI T1040RDB is configured as serdes protocol 0x66 which can support following interfaces 2 RGMIIS on DTSEC4, DTSEC5 1 SGMII on DTSEC3 T1042RDB_PI is configured as serdes protocol 0x06 which can support following interfaces 2 RGMIIS on DTSEC4, DTSEC5 Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> [York Sun: Minor change in commit message] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03boards/t1040qds: Adds ethernet support for T1040Prabhakar Kushwaha
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 Define MDIO related configs Added eth.c file Update t1040.c to support RGMII and SGMII Update t1040qds.c to support ethernet Define the PHY address Signed-off-by: Arpit Goel <B44344@freescale.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: remove dash from commit message] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03powerpc/mpc85xx:Fix README to show correct flash memory mapPrabhakar Kushwaha
Due to increased size of u-boot, FMAN ucode start address has been shifted by 256KB causing a overlap with rootfs start address. Update rootfs start address to reflect correct memory map. Also fix minor typo in README Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03config: trats: trats2: extend dfu_alt_info by env update settingsPrzemyslaw Marczak
This change allows updating environment stored on MMC by dfu or thor. New setting: - "params.bin mmc 0x38 0x8" File params.bin can be generated by: tools/mkenvimage. e.g. ./mkenvimage -s 4096 -o params.bin <env_text_file> Every new env variable in text file should start with a new line. Sample env text file: - board/samsung/common/dfu_sample_env.txt Requirements: - file name: "params.bin" - file size: 4096 Bytes - the same as CONFIG_ENV_SIZE. Other size will cause CRC miscalculation at boot. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> CC: Piotr Wilczek <p.wilczek@samsung.com> CC: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03universal: add LCD download menu supportPrzemyslaw Marczak
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03trats2: add LCD download menu supportPrzemyslaw Marczak
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03trats: add LCD download menu supportPrzemyslaw Marczak
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03samsung: misc: Add LCD download menu.Przemyslaw Marczak
This simple LCD menu allows run one of download mode on device without writing on console or for fast and easy upgrade. This feature check user keys combination at boot: - power key + volume up - download menu - power key + volume down - thor mode (without menu) New configs: - CONFIG_LCD_MENU - CONFIG_LCD_MENU_BOARD For proper effect this feature needs following definitions: Power key: - KEY_PWR_PMIC_NAME - (string) pmic which supports power key check Register address: - KEY_PWR_STATUS_REG - KEY_PWR_INTERRUPT_REG Register power key mask: - KEY_PWR_STATUS_MASK - KEY_PWR_INTERRUPT_MASK Gpio numbers: - KEY_PWR_INTERRUPT_MASK - KEY_VOL_DOWN_GPIO Functions needs to be called: - keys_init() - for set proper gpio direction - check_boot_mode() - menu - main function Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03samsung: boards: update display configs with 16bpp mode.Przemyslaw Marczak
16 bpp mode is required by LCD console mode. This change updates exynos board files. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03lib: tizen: change Tizen logo with the new one.Przemyslaw Marczak
Changes: - check image bpp instead of resolution when returns logo address - remove 32bpp logo - add 16bpp logo in two formats: bmp and gzipped bmp - init logo address with "0" for unsupported bpp mode - update boards configs with proper image size for gunzip - extend structure vidinfo by two fields: logo_x_offset and logo_y_offset. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Tested-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03samsung: common: Add file for common functions, draw_logo() cleanup.Przemyslaw Marczak
Changes: new file: - board/samsung/common/misc.c depends on: CONFIG_MISC_COMMON - move draw_logo() to misc.c configs: trats, trats2, universal: - enable CONFIG_MISC_COMMON, - enable CONFIG_MISC_INIT_R, - add misc_init_r() and call draw_logo() in it. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03trats2: Code cleanup.Przemyslaw Marczak
Remove wrong and unused env variables Trats2 is not as GT-I8800. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Cc: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03s5p: gpio: change gpio coding method for s5p gpio.Przemyslaw Marczak
Old s5p gpio coding method was not clean and was not working properly for all parts and banks. New method is clean and easy to extend. Gpio coding mask: 0x000000ff - pin number 0x00ffff00 - bank offset 0xff000000 - part number Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03smdk5250: Remove 'board_usb_vbus_init()' functionVivek Gautam
Previously as a part of moving the VBUS gpio support to device tree following patch removed this and added relevant support in driver: 4a271cb exynos: usb: Switch USB VBUS GPIOs to be device tree configured Recent changes for common board file migration for exynos platform added it again. So removing it now. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03exynos5250: usb: Fix VBus gpio numbers for ehci and xhci controllersVivek Gautam
The gpio_*() apis require the exact gpio line number to deduce the gpio bank and the gpio pin addresses. So fix the gpio number for VBUS used for EHCI ports as well as XHCI ports on exynos5250 boards. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-01-29board: nios2: Check if flash is configured before calling ↵Ezequiel Garcia
early_flash_cmd_reset() If CONFIG_CFI_FLASH_MTD is not defined, then we shouldn't perform the flash early reset. This commit fixes the following build error: nios2-generic.c: In function `__early_flash_cmd_reset': nios2-generic.c:23: error: `AMD_CMD_RESET' undeclared (first use in this function) nios2-generic.c:23: error: (Each undeclared identifier is reported only once nios2-generic.c:23: error: for each function it appears in.) nios2-generic.c:24: error: `FLASH_CMD_RESET' undeclared (first use in this function) which was introduced by: commit a113fb39df43546c704aa8eba55720da9a9dfedd Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Date: Fri Dec 20 18:34:53 2013 -0300 board: nios2: Add CONFIG_CFI_FLASH_MTD guard to flash.h header include Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Thomas Chou <thomas@wytron.com.tw> Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
2014-01-29Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-28Merge branch 'u-boot-arm/next' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-26nitrogen6x: README: Do not refer to MAINTAINERS fileFabio Estevam
MAINTAINERS file has been removed from the project. Replace its reference with 'boards.cfg' file instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-01-26nitrogen6x: README: Only calling 'make' is enoughFabio Estevam
No need to pass 'u-boot.imx' as parameter for 'make' because u-boot.imx is built by default. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-01-24board: delete meaningless serial.hMasahiro Yamada
Delete some serial.h files, whole code in which is surrounded by #if 0 ... #endif Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de>
2014-01-24board: tec-ng: Do not make directories in a board MakefileMasahiro Yamada
Commit e5c5301f refactored the build system not to make directories in board makefiles. But commit 8f380381 create directories again in board/avionic-design/tec-ng/Makefile. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Alban Bedel <alban.bedel@avionic-design.de>
2014-01-24board: delete unused header filesMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2014-01-24Remove obsolete _LINUX_CONFIG_H macroMasahiro Yamada
Commit 643aae1406c93ddc64fcf8c136b47cdffd9c8ccd deleted include/linux/config.h but missed to delete _LINUX_CONFIG_H macro. It is no longer used at all. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24lib: time: add weak timer_init() functionDarwin Rambo
If timer_init() is made a weak stub function, then it allows us to remove several empty timer_init functions for those boards that already have a timer initialized when u-boot starts. Architectures that use the timer framework may also remove the need for timer.c. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
2014-01-24ARM: AM43xx: Enable DDR dynamic IO power down for DDR3Lokesh Vutla
This patch enables dynamically powering down the IO receiver when not performing a read on DDR3 board. This optimizes both active and standby power consumption. This is derived from a patch that is done on AM335x[1] [1] http://arago-project.org/git/projects/?p=u-boot-am33x.git;a=commit;h=6a9ee4bc72ece53fabf01825605fba3d71d5feb2 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-01-24ARM: OMAP4/5: Remove dead code against CONFIG_SYS_ENABLE_PADS_ALLJassi Brar
The commit f3f98bb0 : "ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls" removed the config option aimed towards moving that stuff into kernel, which renders some code unreachable. Remove that code. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2014-01-22eSDHC: Calculate envaddr accroding to the address formatHaijun.Zhang
On BSC9131, BSC9132, P1010 : For High Capacity SD Cards (> 2 GBytes), the 32-bit source address specifies the memory address in block address format. Block length is fixed to 512 bytes as per the SD High Capacity specification. So we need to convert the block address format to byte address format to calculate the envaddr. If there is no enough space for environment variables or envaddr is larger than 4GiB, we relocate the envaddr to 0x400. The address relocated is in the front of the first partition that is assigned for sdboot only. Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21powerpc/mpc85xx:Increase binary size for P, B & T series boards.Prabhakar Kushwaha
u-boot binary size for Freescale mpc85xx platforms is 512KB. This has been reached to upper limit for some of the platforms causig linker error. So, Increase the u-boot binary size to 768KB. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2014-01-21t2080qds/ddr: update ddr parametersShengzhou Liu
- Optimize UDIMM parameters for whole range from 1500MT/s to 2140MT/s. - Remove unused patameters: 'cpo', 'wrdata delay', '2T', which are unrelated to DDR3/3L. Tested with UDIMM 9JSF25672AZ-2G1K1 and verified speed 1200/1866/2133MT/s. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPLPo Liu
Using the TPL/SPL method to booting from 8k page NAND flash. - Add 256kB size SRAM tlb for second step booting; - Add spl.c for TPL image boot; - Add spl_minimal.c for minimal SPL image; - Add C29XPCIE_NAND configure; - Modify C29XPCIE.h for nand config and enviroment; Signed-off-by: Po Liu <Po.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21powerpc/t2080qds: some update for t2080qdsShengzhou Liu
- add more serdes protocols support. - fix some serdes lanes route. - fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d. - correct boot location info for SD/SPI boot. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21powerpc/t1040qds: Update DDR initialization related settingsPriyanka Jain
Update following DDR related settings for T1040QDS -Correct number of chip selects to two as t1040qds supports two Chip selects. -Update board_specific_parameters udimm structure with settings derived via calibration. -Reduced I2C speed to 50KHz as DDR-SPD does not get reliably read at 400KHz. Verified the updated settings to be working fine with dual-ranked Micron, MT18KSF51272AZ-1G6 DIMM at data rate 833MT/s, 1333MT/s and 1600MT/s. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-20ARM: rpi_b: power on SDHCI and USB HW modulesStephen Warren
Send RPC commands to the VideoCore to turn on the SDHCI and USB modules. For SDHCI this isn't needed in practice, since the firmware already turned on the power in order to load U-Boot. However, it's best to be explicit. For USB, this is necessary, since the module isn't powered otherwise. This will allow the kernel USB driver to work. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-01-20board:universal: fix i2c adapterPiotr Wilczek
Universal uses only one adapter I2C_0. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
2014-01-16Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-01-16arm: lager: Disable TMU0 before OS bootNobuhiro Iwamatsu
On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel and other. This disables TMU0 at the request of from kernel user. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-01-16arm: koelsch: Disable TMU0 before OS bootNobuhiro Iwamatsu
On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel and other. This disables TMU0 at the request of from kernel user. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-01-15Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-01-15mx6: Add initial support for the Hummingboard soloFabio Estevam
SolidRun has designed the Hummingboard board based on mx6q/dl/solo. Add the initial support for the mx6 solo variant. More information about this hardware can be found at: http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware (Carrier-One was the previous name of Hummingboard). Based on the work from Jon Nettleton <jon.nettleton@gmail.com>. Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-01-15mx6: clock: Pass the frequency as argument of enable_fec_anatop_clock()Fabio Estevam
Provide an argument to enable_fec_anatop_clock() to specify the clock frequency that will be generated. No changes are made to mx6slevk, which uses the default 50MHz fec clock. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-14Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-01-14board: nios2: Add CONFIG_CFI_FLASH_MTD guard to flash.h header includeEzequiel Garcia
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
2014-01-14Merge 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
generated by cgit (git 2.34.1) at 2025-01-06 07:56:20 +0000