summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-08-12board/BuR/brsmarc1: initial commitHannes Schmelzer
This commit adds support for the B&R brsmarc1 SoM. The SoM is based on TI's AM335x SoC. Mainly vxWorks 6.9.4.x is running on the board, doing some PLC stuff on various carrier boards. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-12ARM: omap3: overo: Fix MMC init for SPLAnselm Busse
The SPL for the Overo board does not initialise the MMC. Hence, it cannot load the main boot loader from the SD card susequently. This patch moves the initialisation code for the MMC so it gets included in the SPL. [trini: Add missing header] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-11board: siemens: extend factoryset reading for giedi and deneb boardsAnatolij Gustschin
giedi and deneb are i.MX8X based and have additional data with WLAN MAC in factoryset container. Enable building for these boards and adapt factoryset functions to set WLAN MAC and dtb name in environment. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-08-11board: siemens: adapt factoryset reading for DM_I2C enabled boardsAnatolij Gustschin
For new boards we always enable DM_I2C. Extend factoryset functions to support EEPROM reading on these boards. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-08-10Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- R8A77980 V3H support
2019-08-09Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Enable SD slot on Intel Edison - Populate CSRT ACPI table for shared DMA controller on Intel Tangier - Convert Intel ICH-SPI driver to use new spi-mem ops - Enable config_distro_bootcmd for QEMU x86 - Support U-Boot as a payload for Intel Slim Bootloader - Avoid writing temporary asl files into the source tree which fixes the parallel build issue occasionally seen
2019-08-09ARM: renesas: Add R8A77980 V3H Condor board codeMarek Vasut
Add board code for the R8A77980 V3H Condor board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-08-09apalis-tk1: support v1.2 hardware revisionMarcel Ziswiler
Support the V1.2 hardware revision with the following pin muxing changes: Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4 are now used as DDC pins. Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are now used as USB power enable signals. Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power enable signals are now used as GPIO3 and GPIO4. Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is loaded on V1.2 and later modules and resp. USB power enable signals activated. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09apalis-tk1: remove non-essential power rails on bootDominik Sliwa
When mainline kernels reboot TK1 they use SW_RESET, that reset mode does not reset PMIC. Some rails need to be off for RAM Re-repair to work correctly. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09apalis-tk1: set apalis gpio 8 aka fan_enIgor Opaniuk
Make sure the Apalis GPIO 8 aka FAN_EN is on when using Apalis TK1 modules. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09apalis-tk1: do not explicitly release reset_moci#Marcel Ziswiler
By keeping RESET_MOCI_CTRL low we avoid explicitly releasing RESET_MOCI#. Please note that module hardware versions up to V1.1A will already release RESET_MOCI# in hardware coming out of reset. Please further note that with this change the USB hub on the Apalis Evaluation board is kept in reset in U-Boot and therefore none of its ports are operational in U-Boot. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-08-09board: intel: Add new slimbootloader boardPark, Aiden
Add slimbootloader board to run U-boot as a Slim Bootloader payload - Add new board/intel/slimbootloader directory with minimum codes - Add slimbootloader configuration files - Add doc/board/intel/slimbootloader.rst Signed-off-by: Aiden Park <aiden.park@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: add slimbootloader board MAINTAINERS file] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-09x86: edison: Enable SD slotAndy Shevchenko
Enable SD slot on Intel Edison platform. By default firmware doesn't put device on active state. Thus, we have to do this explicitly. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-08-09Merge tag 'u-boot-rockchip-20190809' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Add rk3399 boards Khadas Edge/-V/-Captain - Add fully souce code support for rk3328 including TPL/DRAM init - Enable boot from eMMC for rk3399 rock960/ficus boards - turn on the IO supply for dw_mmc
2019-08-05arm64: dts: rockchip: Add support for Khadas Edge-CaptainNick Xie
Add devicetree support for Khadas Edge-Captain. Khadas Captain is the carrier board for Khadas Edge. Specification - Rockchip RK3399 - Dual-Channel 2GB/4GB LPDDR4 - SD card slot - Onboard 16GB/32GB/128GB eMMC - RTL8211FD 1Gbps - AP6356S/AP6398S WiFI/BT - HDMI Out, DP, MIPI DSI/CSI, eDP - USB 3.0, 2.0 - USB Type C power and data - GPIO expansion ports - Full 4 Lane M.2 Socket - 16MB SPI Flash - IR - Programmable MCU Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2: "arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards" (sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e) Signed-off-by: Nick Xie <nick@khadas.com> Tested-by: Chris Webb <chris@arachsys.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05arm64: dts: rockchip: Add support for Khadas Edge-VNick Xie
Add devicetree support for Khadas Edge-V. Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board. Specification - Rockchip RK3399 - Dual-Channel 2GB/4GB LPDDR4 - SD card slot - Onboard 16GB/32GB/128GB eMMC - RTL8211FD 1Gbps - AP6356S/AP6398S WiFI/BT - HDMI Out, DP, MIPI DSI/CSI, eDP - USB 3.0, 2.0 - USB Type C power and data - GPIO expansion ports - Full 4 Lane M.2 Socket - 16MB SPI Flash - IR - Programmable MCU Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2: "arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards" (sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e) Signed-off-by: Nick Xie <nick@khadas.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-05arm64: dts: rockchip: Add support for Khadas EdgeNick Xie
Add devicetree support for Khadas Edge. Khadas Edge is an expandable Rockchip RK3399 board with goldfinger. Specification - Rockchip RK3399 - Dual-Channel 2GB/4GB LPDDR4 - Onboard 16GB/32GB/128GB eMMC - RTL8211FD 1Gbps - AP6356S/AP6398S WiFI/BT - HDMI Out, DP - USB 3.0, 2.0 - USB Type C power and data - 16MB SPI Flash - Programmable MCU Commit details of rk3399-khadas-edge-*.dts sync from Linux 5.3-rc2: "arm64: dts: rockchip: Add support for Khadas Edge/Edge-V/Captain boards" (sha1: c2aacceedc86af87428d998e23a1aca24fd8aa2e) Signed-off-by: Nick Xie <nick@khadas.com> Tested-by: Chris Webb <chris@arachsys.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-31Merge tag 'u-boot-amlogic-20190731' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - sync Amlogic G12A DT with linux 5.3-rc1 - add support for 4GiB DRAM memory - add support for Amlogic G12B based Odroid-N2 - small duplicate logic fix for gxbb clock driver
2019-07-31Revert "ARM: davinci: da850: Manual pinmux only when PINCTRL not available"Adam Ford
This reverts commit 877ab2423bc257045a06bc23d4b9440b82bda6fb. The above patch was designed to shrink code by only pin-muxing items needed for SPL in SPL and relying on driver model or SPL to mux other items. Unfortunately, da850evm_direct_nor doesn't use SPL so items that were only muxed during SPL are not muxed causing the board to no longer boot. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-31ARM: da850-evm: Remove references to CONFIG_DA850_AM18X_EVMAdam Ford
With the removal of da850_am18xxevm, there is at least one whitelisted CONFIG option that can be deleted. This patch removes CONFIG_DA850_AM18X_EVM since it's not required any more Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-31board: amlogic: add support for Odroid-N2Neil Armstrong
ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd with the following specifications: - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC - 4GB DDR4 SDRAM - Gigabit Ethernet - HDMI 2.1 4K/60Hz display - 40-pin GPIO header - 4 x USB 3.0 Host, 1 x USB OTG - eMMC, microSD - Infrared receiver The board directory is W400, the name of the Amlogic Reference Design of Amlogic G12B with Gigabit boards, which will be used for similar boards. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Mark Kettenis <kettenis@openbsd.org>
2019-07-30Merge tag 'xilinx-for-v2019.10' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2019.10 fpga: - Xilinx virtex2 cleanup - Altera cyclon2 cleanup zynq: - Minor Kconfig cleanup - Add psu_init configuration for Z-turn board zynqmp: - Add support for pmufw config passing to PMU - script for psu_init conversion - zcu1275 renaming xilinx: - Add support for UltraZed-EV SoM
2019-07-30Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2019-07-30arm64: zynqmp: Do not include pm_cfg_obj.o when SPL is disabledMichal Simek
xilinx_zynqmp_mini configuration is throwing build error: readlink: missing operand Try 'readlink --help' for more information. because CONFIG_ZYNQMP_SPL_PM_CFG_OBJ_FILE is not defined at all and Makefile pass ifneq condition. Add SPL_BUILD dependency which is also reflected in Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30arm64: zynqmp: add MAINTAINERS entry for Avnet UltraZed-EVLuca Ceresoli
The board was added without adding a MAINTAINERS entry. Fixes: $ ./tools/genboardscfg.py -f WARNING: no status info for 'avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0' WARNING: no maintainers for 'avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0' $ Reported-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30arm64: zynqmp: add support for Avnet UltraZed-EV Starter KitLuca Ceresoli
Avnet UltraZed-EV Starter Kit is composed by the UltraZed-EV SoM and the only publicly-available compatible carrier card. The SoM is based on the EV version of the Xilinx ZynqMP SoC+FPGA. The psu_init_gpl.c file has been generated from the board definition files at [0] using Vivado 2018.3 and then minimized by tools/zynqmp_psu_init_minimize.sh. Manually removed serdes init code since it is not mentioned in device tree and fixed a checkpatch error. [0] https://github.com/Avnet/bdf/tree/3686c9ff7d2f0467fb4fcf39f861b8d6ff183b12/ultrazed_7ev_cc/1.1 Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30ARM: zynq: Add configuration for Z-turn boardAnton Gerasimov
Basic (PS-only) configuration based on Vivado board files by Sergiusz Bazanski <sergius@q3k.org> Signed-off-by: Anton Gerasimov <tossel@gmail.com>
2019-07-30arm64: zynqmp: xil_io.h: declare functions as staticLuca Ceresoli
Fixes sparse warnings when building zynqmp defconfigs: ./board/xilinx/zynqmp/xil_io.h:12:6: warning: symbol 'Xil_Out32' was not declared. Should it be static? ./board/xilinx/zynqmp/xil_io.h:17:5: warning: symbol 'Xil_In32' was not declared. Should it be static? ./board/xilinx/zynqmp/xil_io.h:22:6: warning: symbol 'usleep' was not declared. Should it be static? Also add __maybe_unused to usleep() since it is not used by minimized psu_init_gpl.c files, so it would warn as "defined but not used". Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-30arm64: zynqmp: spl: install a PMU firmware config object at runtimeLuca Ceresoli
Optionally allow U-Boot to load a configuration object into the Power Management Unit (PMU) firmware on Xilinx ZynqMP. The configuration object is required by the PMU FW to enable most SoC peripherals. So far the only way to boot using U-Boot SPL was to hard-code the configuration object in the PMU firmware. Allow a different boot process, where the PMU FW is equal for any ZynqMP chip and its configuration is passed at runtime by U-Boot SPL. All the code for Inter-processor communication with the PMU is isolated in a new file (pmu_ipc.c). The code is inspired by the same feature as implemented in the Xilinx First Stage Bootloader (FSBL) and Arm Trusted Firmware: * https://github.com/Xilinx/embeddedsw/blob/fb647e6b4c00f5154eba52a88b948195b6f1dc2b/lib/sw_apps/zynqmp_fsbl/src/xfsbl_misc_drivers.c#L295 * https://github.com/ARM-software/arm-trusted-firmware/blob/c48d02bade88b07fa7f43aa44e5217f68e5d047f/plat/xilinx/zynqmp/pm_service/pm_api_sys.c#L357 SPL logs on the console before loading the configuration object: U-Boot SPL 2019.07-rc1-00511-gaec224515c87 (May 15 2019 - 08:43:41 +0200) Loading PMUFW cfg obj (2008 bytes) EL Level: EL3 ... Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-29Merge branch '2019-07-29-ti-imports'Tom Rini
- More DaVinci DM migration, drop am18xx EVM platform - Keystone bug fix
2019-07-29davinci: omapl138-lcdk: enable driver-model in SPLBartosz Golaszewski
Enable CONFIG_SPL_DM and enable the driver model for serial by defining an appropriate device in the board file for da850-lcdk. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-07-29davinci: omapl138-lcdk: remove unneeded includesBartosz Golaszewski
There's no SPI on da850-lcdk. Remove unnecessary includes. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-07-29ARM: da850_am18xxevm: Remove config and referencesAdam Ford
This board has been abandonded for a while. I do not have this hardware and nobody has appeared to notice and/or care that it's orphaned. Since much of this code is inserted into the da850evm code base, removing it from support will make da850evm support easier going forward. This patch removes the da850_am18xxevm_defconfig, README references to this board and the reference to this board from the MAINTAINERS list. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-29Merge branch '2019-07-29-master-imports'Tom Rini
- Assorted bug fixes
2019-07-29board: mediatek: Add pumpkin board supportFabien Parent
The pumpkin board is made by Gossamer Engineering and is using a MediaTek SoC. The board currently comes in two available version: MT8516 SoC and MT8167 SoC. The board provides the following IOs: eMMC, NAND, SD card, USB type-A, Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in), serial over USB, and an expansion header. Additionally there is a HDMI port, DSI port, and camera port only on the MT8167 version of the board. The board can be powered by battery and/or via a USB Type-C port and is using a PMIC MT6392. The eMMC and NAND are sharing pins and cannot be used together. This commit is adding the basic boot support for the Pumpkin MT8516 board on the eMMC. Signed-off-by: Fabien Parent <fparent@baylibre.com>
2019-07-29Merge tag 'video-for-2019.10' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-video - dcu and imx7 DM_VIDEO conversion - lb070wv8 compatible in simple_panel driver - bmp_logo improvements for DM_VIDEO - EDID updates to filter supported modes - meson_dw_hdmi: support EDID mode filtering - dw_hdmi: support ddc-i2c-bus phandle for external I2C masters - fix rpi crash when firmware doesn't report connected display
2019-07-29Merge tag 'u-boot-rockchip-20190729' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Clean up and migrate to use common rockchip spl board file - Clean up and migrate to use common rockchip board file - Increase rk3288 CONFIG_SYS_BOOTM_LEN to 16MB
2019-07-29rockchip: rv1108: Migrate to use common board fileKever Yang
Use common board file for board_init() and board_late_init(), for Rockchip SoCs have very similar process. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: elgin-rv1108: use board_early_init_f for per-boar initKever Yang
Use board_early_init_f() for per-board init operation and use board_init() from common board file. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3399: Migrate to use common board fileKever Yang
Use common board file for board_init() and board_late_init(), for Rockchip SoCs have very similar process. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3399: init vbus regulator in board_early_init_f()Kever Yang
Handle per-board init in board_early_init_f() and use the common board_init() for per-platform board init later. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3368: Migrate to use common board fileKever Yang
Use common board file for board_init() and board_late_init(), for Rockchip SoCs have very similar process. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3328: Migrate to use common board fileKever Yang
Use common board file for board_init() and board_late_init(), for Rockchip SoCs have very similar process. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
2019-07-29rockchip: rk3288: Move rk3288_detect_reset_reason to soc fileKever Yang
The rk3288_detect_reset_reason() is per-SoC operation, move it to rk3288.c, and extend the rk_board_late_init() with rk3288_board_late_init() to make all the board works fine as before. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3288: Move veyron_init() back to veyron.cKever Yang
The veyron_init() should go to its board file veyron.c, and the board_early_init_f() could be the right place. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3288: move board_early_init_f() back to veyronKever Yang
The board_early_init_f() is only used by veyron board now, move it into the board file veyron.c Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: sdram_common: add common dram_init_banksizeKever Yang
dram_init_banksize() can be common used by all SoCs, move it into sdram_common.c Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: clean up board_usb_init() for all SoCsKever Yang
Use "snps,dwc2" for compatible name and and common variable names so that we can share the common code for all SoCs. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3399: move chromebook bob specific flow to its board fileKever Yang
Add a board_early_init_f() in board_init_f() and move the board specific init code into its own board file. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-29rockchip: rk3288-phycore: move phycore_init() to its own board fileKever Yang
phycore_init() is use for phycore board only, it should be move back to phycore-rk3288.c Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
generated by cgit (git 2.34.1) at 2024-12-29 02:28:05 +0000