summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2014-02-17Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-02-17Merge branch 'master' of git://git.denx.de/u-boot-mmcTom Rini
2014-02-13arm/km: introduce kmsugp1 targetGerlando Falauto
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA. The only difference is that the PCIe reset is connected to Kirkwood pin MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7. Such pin should theoretically be handled by the PCIe subsystem automatically, but this turned out not to be the case. So simply configure this PIN as a GPIO and issue a pulse manually. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com> Cc: Valentin Longchamp <valenting.longchamp@keymile.com> Cc: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: define fdt_high env variable and allow backwards compatibilityGerlando Falauto
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high" This is necessary on Kirkwood so that the FDT does not get relocated above the memory limit that the kernel cannot access (that is the memory part reserved for the switch). This was tested on NUSA1, where it is necessary, and on ETER1, where it doesn't seem to hurt. We want the scripts to also work with older versions of u-boot, where: a) set_fdthigh is not defined (will be default env for newer u-boots) b) the fdt will not be available For this reason, we use "set_fdthigh" to tell whether we are running a newer (FDT-aware) u-boot or not. So if "set_fdthigh" runs successfully or arch != arm we try loading the fdt; otherwise we proceed normally. Notice how, contrary to release mode, set_fdthigh will _not_ be part of subbootcmds for develop and ramfs, but will be executed as part of "tftpfdt". Since this is only needed for kirkwood cards, and it prevents the kernel from booting on QorIQ (though it seemed to work on ETER1), we change its definition in the default env for powerpc so that the value is only set on ARM. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: enable FDT for km_kirwkoodGerlando Falauto
This consists of: a) Defining the addresses, enabling fdtsupport [arm] b) Defining "cramfsloadfdt" [arm,powerpc => common] c) Adding the FDT address to bootm [arm,powerpc => common] d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common] This should work with 3.10 kernels, whether loaded through TFTP (with rootfs either through NFS or TFTP-ramfs) or from the NAND. The machid was left unchanged, this should keep compatibility with both older and newer kernels. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: fix wrong error handlingHolger Brunck
miiphy_read and miiphy_write are returning 0 on success. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: make local function startup_allowed staticHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: drop unneeded defineHolger Brunck
CONFIG_BOOTCOUNT_LIMIT is used on all boards from this board series. So remove this unneeded define. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-02-11Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic
2014-02-11mx6qsabreauto: Update imximage.cfgFabio Estevam
Use the latest DDR and clock settings as the one from Freescale BSP. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-02-11hummingboard: Return from cpu_eth_init() directlyFabio Estevam
There is no need to print an error message when cpu_eth_init() fails because net/eth.c already prints it. In order to simplify the code, just return the value from cpu_eth_init(bis) directly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-02-07dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini
Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07omap5_uevm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini
Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07net/designware - switch driver to phylib usageAlexey Brodkin
With this change driver will benefit from existing phylib and thus custom phy functionality implemented in the driver will go away: * Instantiation of the driver is now much shorter - 2 parameters instead of 4. * Simplified phy management/functoinality in driver is replaced with rich functionality of phylib. * Support of custom phy initialization is now done with existing "board_phy_config". Note that after this change some previously used config options (driver-specific PHY configuration) will be obsolete and they are simply substituted with similar options of phylib. For example: * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled by default. * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise automatically the first discovered on MDIO bus phy will be used I believe there's no need now in "doc/README.designware_eth" because user only needs to instantiate the driver with "designware_initialize" whose prototype exists in "include/netdev.h". Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Stefan Roese <sr@denx.de> Cc: Mischa Jonker <mjonker@synopsys.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Amit Virdi <amit.virdi@st.com> Cc: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-07arc: add AXS101 board supportAlexey Brodkin
AXS101 is a new generation of devlopment boards from Synopsys that houses ASIC with ARC700 and lots of DesignWare peripherals: * DW APB UART * DW Mobile Storage (MMC/SD) * DW I2C * DW GMAC Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-02-07arc: add Arcangel4 board supportAlexey Brodkin
Arcangel4 is a FPGA-based development board that is used for prototyping and verificationof of both ARC hardware (CPUs) and software running upon CPU. This board avaialble in 2 flavours: * Little-endian (arcangel4) * Big-endian (arcangel4-be) Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-02-07board:samsung:trats2: add env variables describing platformPiotr Wilczek
This patch adds variables describing platform (soc, board, vendor) to default environment. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07board:samsung:trats: add env variables describing platformPiotr Wilczek
This patch adds variables describing platform (soc, board, vendor) to default environment. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07board:samsung:universal: add env variables describing platformPiotr Wilczek
This patch adds variables describing platform (soc, board, vendor) to default environment. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07board:samsung:goni: add env variables describing platformPiotr Wilczek
This patch adds variables describing platform (soc, board, vendor) to default environment. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-07board:samsung:common: set envs with board unified informationPiotr Wilczek
This patch sets envs that describe board information. The following envs are set: soc_id, soc_rev, board_rev. Based on this information, if CONFIG_OF_LIBFDT is enabled, the 'fdtfile' env is set as: fdtfile=${soc_family}${soc_id}-${board}.dtb The generated envs are intenionally not saved to persistent storage. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-06Merge branch 'fpga' of git://www.denx.de/git/u-boot-microblazeTom Rini
2014-02-06fpga: zynqpl: Add support for zc7015 deviceMichal Simek
Just extend tables with this new device. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-06usb: mv_udc: Rename to ci_udcMarek Vasut
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc instead. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Stefano Babic <sbabic@denx.de>
2014-02-06ARM: IXP: Remove dvl_host boardMarek Vasut
The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
2014-02-06ARM: IXP: Remove actux4 boardMarek Vasut
The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
2014-02-06ARM: IXP: Remove actux3 boardMarek Vasut
The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
2014-02-06ARM: IXP: Remove actux2 boardMarek Vasut
The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
2014-02-06ARM: IXP: Remove actux1 boardMarek Vasut
The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
2014-02-03ARM: tegra: add Venice2 (Tegra124) boardTom Warren
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC files. PMIC init will be moved to pmic_common_init later. This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display and WB/LP0 are not supported yet. Signed-off-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03ARM: tegra: add DT files for Tegra124 and Venice2Tom Warren
These are fairly complete, and near-clones of Tegra114 Venice, with an additional I2C port, and MMC address changes for Tegra124. Signed-off-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03ARM: tegra: only build __pinmux_nand() when it's neededTom Warren
__pinmux_nand() won't compile if PERIPH_ID_NDFLASH isn't defined. Prevent this from causing build problems on newer SoCs without NAND support (or without SW support for NAND yet), but preventing compilation unless the function will actually be used, i.e. when CONFIG_TEGRA_NAND is defined. Signed-off-by: Tom Warren <twarren@nvidia.com> [swarren, rewrote commit description, moved ifdef around whole function rather than just body] Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03kmp204x: initial support for PCIe FPGA configurationValentin Longchamp
The PEXHC PCIe configuration mechanism ensures that the FPGA get configured at power-up. Since all the PCIe devices should be configured when the kernel start, u-boot has to take care that the FPGA gets configured also in other reset scenarios, mostly because of possible configuration change. The used mechanism is taken from the km_kirkwood design and adapted to the kmp204x case (slightly different HW and PCIe configuration). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: update I2C field of RCWValentin Longchamp
On the previous HW revision (now unsupported), there was a need for external DMA signals and thus the I2C3/4 signals were used DMA1_DONE/ACK/REQ. These signals now are configured as GPIO[16:19]. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: implement workaround for A-006559Valentin Longchamp
According to the errata, some bits of an undocumented register in the DCSR must be set for every core in order to avoid a possible data or instruction corruption. This is required for the 2.0 revision of the P2041 that should be used as soon as available in our design. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: I2C deblocking supportRainer Boschung
This patch adds support for using some GPIOs that are connected to the I2C bus to force the bus lines state and perform some bus deblocking sequences. The KM common deblocking algorithm from board/keymile/common/common.c is used. The GPIO lines used for deblocking the I2C bus are some external GPIOs provided by the QRIO CPLD: - SCL = GPIOA_20 - SDA = GPIOA_21 The QRIO GPIOs act in an open-drain-like manner, for 0 the line is driven low and for 1 the GPIO is set as input and the line gets pulled-up. Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: introduce QRIO GPIO functionsValentin Longchamp
The QRIO GPIO functions can be of general interest. They are thus added to a qrio.c and their prototype are available from kmp204x.h. The QRIO prst function are also included in this file, as well as the functions required for the I2C deblocking support (open-drain). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03kmp204x: support for QRIO1 bootcounterRainer Boschung
Make use of the QRIO1 32bit register at 0x20 as bootcounter register Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> [York Sun: Minor change to commit message] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03powerpc/t104xrdb: Add basic ethernet supportPriyanka Jain
This covers only non-L2 switch ethernet interfaces i.e. RGMII and SGMII interface for both T1040RDB and T1042RDB_PI T1040RDB is configured as serdes protocol 0x66 which can support following interfaces 2 RGMIIS on DTSEC4, DTSEC5 1 SGMII on DTSEC3 T1042RDB_PI is configured as serdes protocol 0x06 which can support following interfaces 2 RGMIIS on DTSEC4, DTSEC5 Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> [York Sun: Minor change in commit message] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03boards/t1040qds: Adds ethernet support for T1040Prabhakar Kushwaha
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 Define MDIO related configs Added eth.c file Update t1040.c to support RGMII and SGMII Update t1040qds.c to support ethernet Define the PHY address Signed-off-by: Arpit Goel <B44344@freescale.com> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: remove dash from commit message] Signed-off-by: York Sun <yorksun@freescale.com>
2014-02-03powerpc/mpc85xx:Fix README to show correct flash memory mapPrabhakar Kushwaha
Due to increased size of u-boot, FMAN ucode start address has been shifted by 256KB causing a overlap with rootfs start address. Update rootfs start address to reflect correct memory map. Also fix minor typo in README Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-03config: trats: trats2: extend dfu_alt_info by env update settingsPrzemyslaw Marczak
This change allows updating environment stored on MMC by dfu or thor. New setting: - "params.bin mmc 0x38 0x8" File params.bin can be generated by: tools/mkenvimage. e.g. ./mkenvimage -s 4096 -o params.bin <env_text_file> Every new env variable in text file should start with a new line. Sample env text file: - board/samsung/common/dfu_sample_env.txt Requirements: - file name: "params.bin" - file size: 4096 Bytes - the same as CONFIG_ENV_SIZE. Other size will cause CRC miscalculation at boot. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> CC: Piotr Wilczek <p.wilczek@samsung.com> CC: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03universal: add LCD download menu supportPrzemyslaw Marczak
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03trats2: add LCD download menu supportPrzemyslaw Marczak
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03trats: add LCD download menu supportPrzemyslaw Marczak
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03samsung: misc: Add LCD download menu.Przemyslaw Marczak
This simple LCD menu allows run one of download mode on device without writing on console or for fast and easy upgrade. This feature check user keys combination at boot: - power key + volume up - download menu - power key + volume down - thor mode (without menu) New configs: - CONFIG_LCD_MENU - CONFIG_LCD_MENU_BOARD For proper effect this feature needs following definitions: Power key: - KEY_PWR_PMIC_NAME - (string) pmic which supports power key check Register address: - KEY_PWR_STATUS_REG - KEY_PWR_INTERRUPT_REG Register power key mask: - KEY_PWR_STATUS_MASK - KEY_PWR_INTERRUPT_MASK Gpio numbers: - KEY_PWR_INTERRUPT_MASK - KEY_VOL_DOWN_GPIO Functions needs to be called: - keys_init() - for set proper gpio direction - check_boot_mode() - menu - main function Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03samsung: boards: update display configs with 16bpp mode.Przemyslaw Marczak
16 bpp mode is required by LCD console mode. This change updates exynos board files. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03lib: tizen: change Tizen logo with the new one.Przemyslaw Marczak
Changes: - check image bpp instead of resolution when returns logo address - remove 32bpp logo - add 16bpp logo in two formats: bmp and gzipped bmp - init logo address with "0" for unsupported bpp mode - update boards configs with proper image size for gunzip - extend structure vidinfo by two fields: logo_x_offset and logo_y_offset. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Tested-by: Hyungwon Hwang <human.hwang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-02-03samsung: common: Add file for common functions, draw_logo() cleanup.Przemyslaw Marczak
Changes: new file: - board/samsung/common/misc.c depends on: CONFIG_MISC_COMMON - move draw_logo() to misc.c configs: trats, trats2, universal: - enable CONFIG_MISC_COMMON, - enable CONFIG_MISC_INIT_R, - add misc_init_r() and call draw_logo() in it. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>