summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-05-21mpc83xx: Get rid of CONFIG_SYS_DDR_SDRAM_BASEMario Six
CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as CONFIG_SYS_SDRAM_BASE on all existing boards. Just use CONFIG_SYS_SDRAM_BASE instead. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21mpc83xx: Get rid of CONFIG_SYS_DDR_BASEMario Six
CONFIG_SYS_DDR_BASE is specific to mpc83xx an is always set to the same value as CONFIG_SYS_SDRAM_BASE. Just use CONFIG_SYS_SDRAM_BASE instead. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21mpc83xx: Migrate CONFIG_SYS_{BR, OR}*_PRELIM to KconfigMario Six
Migrate the BR/OR settings to Kconfig. These must be known at compile time, so cannot be configured via DT. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21tqm834x: Expand CONFIG_SYS_OR_TIMING_FLASH macroMario Six
We want to normalize all BR/OR config lines as much as possible. The TQM834x board uses CONFIG_SYS_OR_TIMING_FLASH in a OR definition, which we want to remove. But CONFIG_SYS_OR_TIMING_FLASH is also used outside of the config file. Replace these usages with the definition of the variable, so we can remove the variable in the next patch. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21mpc83xx: Kconfig: Migrate HRCW to KconfigMario Six
The HRCW (hardware reset configuration word) is a constant that must be hard-coded into the boot loader image. So, it must be available at compile time, and cannot be migrated to the DT mechanism, but has to be kept in Kconfig. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21mpc83xx: Get rid of CONFIG_83XX_CLKINMario Six
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the system clock. To migrate the architecture, we can replace CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ. To do this * replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ * set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all MPC83xx config files Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21mpc83xx: Migrate legacy PCI options to KconfigMario Six
The MPC83xx include files contain some settings of the PCI subsystem. Migrate these to Kconfig until a proper DM PCI driver exists. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21strider: Migrate to CONFIG_TARGET_STRIDERMario Six
Use the proper CONFIG_TARGET_STRIDER Kconfig option to replace the CONFIG_STRIDER ad-hoc config option. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21hrcon: Migrate to CONFIG_TARGET_HRCONMario Six
Use the proper CONFIG_TARGET_HRCON Kconfig option to replace the CONFIG_HRCON ad-hoc config option. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21MPC8349ITX: Migrate to CONFIG_TARGET_MPC8349ITXMario Six
Use the proper CONFIG_TARGET_MPC8349ITX Kconfig option to replace the CONFIG_MPC8349ITX ad-hoc config option. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21MPC832XEMDS: Migrate to CONFIG_TARGET_MPC832XEMDSMario Six
Use the proper CONFIG_TARGET_MPC832XEMDS Kconfig option to replace the CONFIG_MPC832XEMDS ad-hoc config option. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21mpc83xx: Make distinct MPC8349EMDS_SDRAM boardMario Six
The MPC8349EMDS config file contains config options to enable SDRAM support. To keep this ability after the Kconfig migration, create a new MPC8349EMDS_SDRAM board that enables the SDRAM support and remove the SDRAM support from the original board. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20mpc83xx: Make distinct caddy2 configMario Six
vme8349.h contains two separate boards: The vme8349 itself, and the caddy2 board. The caddy2 board is chosen by setting certain config variables. Create a proper config file for the caddy2 board to make Kconfig migration easier. Furthermore, simplify the vme8349 and caddy2 configs by keeping only the options necessary for each board. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20mpc83xx: Make distinct MPC8313ERDB targetsMario Six
MPC8313ERDB has the option of either enabling NOR or NAND boot in its config file (by commenting out certain #ifdefs). To keep this ability after migrating options to Kconfig, we introduce two MPC8313ERDB configs: one for NOR, and one for NAND. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20keymile: Make distinct kmeter1, and kmcoge5ne configsMario Six
The kmeter1, and kmcoge5ne boards also build from the same config file with #ifdef logic. Create a separate include config for each board with the #ifdef logic resolved as needed. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20keymile: Make distinct kmsupx5, tuge1, kmopti2, and kmtepr2 configsMario Six
The kmsupx5, tuge1, kmopti2, and kmtepr2 boards all build from the same include config file with lots of #ifdef logic. To ease Kconfig migration, create new config include files for these boards, and resolve the #ifdef logic as needed. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20keymile: Make distinct kmtegr1, kmvect1, suvd3 configsMario Six
The kmtegr1, kmvect1, and suvd3 boards all use the same config include file with lots of #ifdefs in it. The Kconfig migation will become easier if we get rid of these #ifdefs first. Hence, create distinct config include files for these boards, and unwind the #ifdef logic in these config files to only include the options necessary for each board. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20mpc83xx: Introduce ARCH_MPC836*Mario Six
Replace CONFIG_MPC836* with proper CONFIG_ARCH_MPC836* Kconfig options. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20mpc83xx: Introduce ARCH_MPC830*Mario Six
Replace CONFIG_MPC830* with proper CONFIG_ARCH_MPC830* Kconfig options. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-20Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
- Fix for mxc_i2c driver in DM mode, thanks to Trent!
2019-05-20arm: imx: cx9020: remove unnecessary includesSteffen Dirkwinkel
There are several includes in mx53cx9020.c which are not required anymore. Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2019-05-20dm: arm: imx: cx9020: remove unused mmc functionsSteffen Dirkwinkel
These mmc functions were not used anymore since DM_MMC was introduced. Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2019-05-20dm: arm: imx: cx9020: migrate to dm_videoSteffen Dirkwinkel
Enable DM_VIDEO in config and don't overwrite console so it can be set from environment Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2019-05-20dm: arm: imx: cx9020: enable DM_GPIOSteffen Dirkwinkel
Switch to DM_GPIO and add gpio_request where necessary. This is needed for DM_VIDEO and fixes an issue with sd card detection which was introduced by the combination of these commits: commit 7a0425dd969c ("mmc: fsl_esdhc: make get_cd work well in dm_mmc_ops") commit 7e04b4c751a1 ("dm: arm: imx: migrate cx9020 to CONFIG_DM_MMC") Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
2019-05-18CONFIG_SPL_SYS_[DI]CACHE_OFF: addTrevor Woerner
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances where these configuration items are conditional on SPL. This commit adds SPL variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates the configurations as required. Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Trevor Woerner <trevor@toganlabs.com> [trini: Make the default depend on the setting for full U-Boot, update more zynq hardware] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-17wandboard: Don't use I2C speed Kconfig settings with DM_I2CTrent Piepho
When using DM_I2C the speed value supplied to setup_i2c() is not used, so this code required CONFIG_SYS_MXC_I2C[12]_SPEED to be defined to compile, but did not actually use them. Change this so we no longer need to define an unused macro to compile in DM_I2C mode. Also make it more clear that they do not control the bus speed. Otherwise it is quite easy to mistakenly believe they are used to set the bus speed. Cc: Heiko Schocher <hs@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Signed-off-by: Trent Piepho <tpiepho@impinj.com>
2019-05-15board: atmel: sama5d2_icp: enable green led on SPL completionEugen Hristev
Enable the green led on SPL completion. Red led has no pulldown and it will be lighted by default when the board starts up. If the PMIC is not configured to enable LDO2, the leds will not light. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-05-15board: atmel: sama5d2_icp: standby disable on CAN transceivers in SPLEugen Hristev
The 2 CAN transceivers have a STBDY pin which must be low in order to operate. This pin is tied to PB25. Set it to 0 in bootstrap. At a later time, this needs to be controlled by Linux power management system, or requested by some driver as a gpio and tied to 0 during CAN link up. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-05-15board: atmel: sama5d2_icp: add periph reset in SPL hw initEugen Hristev
Some periphs on the board need to be reset by holding their reset GPIO down for a specific time period. On a warm reset, the periphs are not being reset by any reset pin and may be in a wrong state. Reset them in the SPL to make sure we are booting into the correct state machine of the specific board periphs (KSZ eth switch, USB hub, HSIC eth, Ethercat) Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-05-14arm: socfpga: Re-add support for Aries MCV SoM and MCVEV[KP] boardWolfgang Grandegger
Re-add support for Aries Embedded MCV SoM, which is CycloneV based and the associated MCVEVK and MCVEVP baseboard. The board can boot from eMMC. Ethernet and USB is supported. The Aries Embedded boards have been removed with commit 03b54997d568 ("board/aries: Remove"). I will now take care of them. The device-tree files are from mainline Linux commit e93c9c99a629 ("Linux v5.1)". Signed-off-by: Wolfgang Grandegger <wg@aries-embedded.de> CC: Marek Vasut <marex@denx.de> CC: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-05-13Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- A10 FPGA programming support, Gen5 livetree conversion
2019-05-10ARM: socfpga: Add default FPGA bitstream fitImage for Arria10 SoCDKTien Fong Chee
Add default fitImage file bundling FPGA bitstreams for Arria10. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
2019-05-10sh: shmin: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-05-10sh: ms7720se: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-05-10sh: mpr2: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Mark Jonas <mark.jonas@de.bosch.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-05-10sh: rsk7269: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-05-10sh: rsk7264: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-05-10sh: rsk7203: Remove the boardMarek Vasut
Last change to this board was done in 2016, has no prospects of ever being converted to DM, drop it. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Chris Brandt <chris.brandt@renesas.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
2019-05-09Merge tag 'rockchip-for-v2019.07-rc1' of git://git.denx.de/u-boot-rockchipTom Rini
Improvements and new features: - split more rockchip pinctrl_core feature into per SoC - enable TPL for evb-rk3399 board - enable TPL/SPL for evb-px5 board - enable TPL and OP-TEE support for evb-rk3229 - update fix in arm common assembly start code for rockchip header file - update default SPL_FIT_GENERATOR for rockchip - rk3399 boards update to use '-u-boot.dtsi' - add new rk3399 boards: Nanopi M4, Nanopc T4 - enable sound for chromebook_minnie
2019-05-09Merge git://git.denx.de/u-boot-marvellTom Rini
- DM updates for multiple MVEBU boards (Stefan) - Add CRS305-1G-4S board (Luka) - Enable MMC in SPL on clearfog (Baruch)
2019-05-09Merge git://git.denx.de/u-boot-riscvTom Rini
- Correct SYS_TEXT_BASE for qemu. - Support booti. - Increase SYSBOOTM_LEN for Fedora/RISCV kernel. - Support SMP booting from flash.
2019-05-09rockchip: rk3399: Add Nanopc T4 board supportJagan Teki
Add initial support for Nanopc T4 board. Specification - Rockchip RK3399 - Dual-Channel 4GB LPDDR3-1866 - SD card slot - 16GB eMMC - RTL8211E 1Gbps - AP6356S WiFI/BT - HDMI In/Out, DP, MIPI DSI/CSI, eDP - USB 3.0, 2.0 - USB Type C power and data - GPIO expansion ports - DC 12V/2A Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2: "arm64: dts: rockchip: Add NanoPC-T4 IR receiver" (sha1: 95658e21b1707ad7844f873db2fdaa295109a5a3) Tested-by: Daniel Gröber <dxld@darkboxed.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-05-09rockchip: rk3399: Add Nanopi M4 board supportJagan Teki
Add initial support for Nanopi M4 board. Specification - Rockchip RK3399 - Dual-Channel 4GB LPDDR3-1866 - SD card slot - eMMC socket - RTL8211E 1Gbps - AP6356S WiFI/BT - HDMI In/Out, DP, MIPI DSI/CSI - USB 3.0 x4 - USB Type C power and data - GPIO1, GPIO2 expansion ports - DC5V/3A Commit details of rk3399-nanopi-m4.dts sync from Linux 5.1-rc2: "arm64: dts: rockchip: Refine nanopi4 differences" (sha1: c62ffaf5026d0b7633e62b2cea8450b5543c349a) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-09riscv: configs: AE350 will use CONFIG_OF_SEPARATE when boots from flashRick Chen
When AE350 boots from flash, use CONFIG_OF_SEPARATE instead of CONFIG_OF_BOARD. Also remove unused code about prior_stage_fdt_address. And modify CONFIG_SYS_FDT_BASE as flash address. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-05-09riscv: configs: Support AE350 SMP booting from flash flowRick Chen
Add two defconfigs to support AE350 SMP booting from flash. Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-05-09riscv: qemu: Use correct SYS_TEXT_BASE for S-mode on 32bit systemAnup Patel
For 32bit system, the OpenSBI (or BBL) will jump to 0x80400000 address in S-mode whereas for 64bit system it will jump to 0x80200000 address in S-mode. Currently, the S-mode U-Boot sets SYS_TEXT_BASE to 0x80200000 for both 32bit and 64bit system. This breaks S-mode U-Boot for 32bit system. This patch sets different SYS_TEXT_BASE for 32bit and 64bit system so that S-mode U-Boot works fine for both. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Tested-by: Karsten Merker <merker@debian.org>
2019-05-09arm: mvebu: Add CRS305-1G-4S boardLuka Kovacic
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and like some of the other similar boards requires bin_hdr. bin_hdr (DDR3 init stage) is currently retrieved from the stock bootloader and compiled into the kwb image. Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip support and writing env to SPI flash. Signed-off-by: Luka Kovacic <me@lukakovacic.xyz> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-05-08Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
- Various PHY fixes / enhancements. - TI K2G fixes
2019-05-08ARM: k2g-ice: Add pinmux support for rgmii interfaceMurali Karicheri
This add pinmux configuration for rgmii interface so that network driver can be supported on K2G ICE boards. The pinmux configurations for this are generated using the pinmux tool at https://dev.ti.com/pinmux/app.html#/default As this required some BUFFER_CLASS definitions, same is re-used from the linux defnitions in include/dt-bindings/pinctrl/keystone.h Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-05-08ARM: k2g-gp-evm: update to rgmii pinmux configurationMurali Karicheri
This patch updates pinmux configuration for K2G GP EVM based on data generated by the pinmux tool at https://dev.ti.com/pinmux/app.html#/default Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
generated by cgit (git 2.34.1) at 2025-01-07 17:20:46 +0000